Question about 2004 Toyota Camry

1 Answer

How do you replace 2004 Camry Fog Lamps?

Manual says that you have to take car to dealer to change fog lamps. Is there a way to do it yourself?

Posted by on

  • sc430sa Mar 02, 2009

    I happen to have a 2005 camry se, does that same rule still apply to changing out the fog light bulb?

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 86 Answers

Yes, position self in front of the fog lamps, push the fog lamps light assembly and slide it to the direction of the center of your car, wait for a part of the assembly to pop-out and pull the whole assembly out. No screws involve

Posted on Nov 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How turn on my fog lights on 99 montana or its turn on by itself


Fog Lamps The fog lamps switch is located in the instrument panel switchbank. Push the fog lamp symbol on the switch to turn on the lamps. The indicator light will glow. Push the ribbed part of the switch to turn them off. The indicator light will go off. Your parking lamps or headlamps must be on for your fog lamps to go on.
http://www.pontiac.com/content/dam/pontiac/northamerica/usa/nscwebsite/en/Home/Owners/Owner_Resources/Manuals/en/us/1999/montana/1999-pontiac-montana-owners-manual.pdf.pdf

Page 2-63 of owners manual

Dec 26, 2015 | Cars & Trucks

3 Answers

How do I turn on fog lights on a Cadillac escalade esv 09


If it is a turn knob for lights just pull out on knob

Apr 27, 2015 | 2009 Cadillac Escalade ESV

1 Answer

How to replace bulb on fog lamps suzuki xl7 2003


this info is in the operators guide, lost that? in the glove box.
my 07 manual shows no fog , lamp instructions
it says contact dealer and as you know they are DOA. Chapter 11.
any mech can do this..
some fogs are optional added lamps to some years, and makes and in some countries (not stated)
but in general its 3 ways.
Look at the lamp , see it?
does the front have screws on the lens. , remove it.
if not its a rear access lamp
gain access to the rear and remove the socket, and replace the lamp,
if all this is too hard, and still a wana DIY,
you could go to alldata.com and read how. under lighting,.
or post a photo of said fog lamp.. my 04 has no such lamp. BTW.
if the lamp need body panel removal. then in the FSM (or above link) you'd read the section under body. for how todo that.

Oct 17, 2013 | 2002 Suzuki XL-7

1 Answer

I have a 2001 jeep grand Cherokee Laredo that did not come with fog lights but has the plugs for the bulbs. I purchased the fog lights plugged them in but they didn't turn on. I was wondering if there...


If this vehicle came prewired, and all you had to do was plug in the fog lamps, then 50A fuse 7 in the power distribution center would be hot at all times, applying power to 15A fuse 24 and the fog lamp relay. Setting the left multifunction switch to FOG causes the body control module to close the fog lamp relay and turn on the fog lamps. It is possible your Jeep came prewired but without the fuses and relay so a dealer could install them to make your fog lamps work. You can check whether the fuses are in the box and OK and whether the fog lamp is installed or just an empty socket. Once everything has been checked and any missing parts installed, your fog lights should work.

Sep 18, 2012 | Cars & Trucks

1 Answer

Anybody know why my fog lights on a mkV R32 won't


Well, First, you get the "dttech DIY auto repair person of the week award" for at least LOOKING in the Owner's Manual first! That is better than MOST Fixya users would do. Probably 90% of the Owner's Manuals in peoples glove boxes are still in the wrappers they came in from the factory!

The reason the Owner's Manual is no help in finding the fog lamp fuse is because the fog lamps do not have their own fuse. The power for the fog lamps is actually supplied by the Vehicle Electrical System Control Module (VESCM), which is located under the left side of the dash.

The fog lamp indicators in the instrument cluster are actually a completely different circuit than the fog lamps themselves. The Instrument Cluster Control Module (ICCM) turns these lamps on when the VESCM sends a message over the data communication line to tell the ICCM that it has turned the fog lamps on. So my guess is that there is no indicator on the dash because the VESCM is not commanding the fog lamps to turn on.

The possible reasons for this could be that the VESCM is not recognizing that you are WANTING the fog lamps on (due to a switch malfunction or a wiring problem between the switch and the VESCM) or the VESCM is malfunctioning, or the VESCM has detected a short circuit in the fog lamp circuits and is refusing to turn them on in an effort to protect the vehicle from burning to the ground.

So, in short, the BEST way to figure out why your fog lamps are not working is to scan your onboard computer network for possible fault codes and check the live input data from the light switch to see if the VESCM is recieving the message that you are trying to turn the fog lamps on, as well as see if the VESCM is commanding the fog lamps on (probably not, or the dash indicators would be on).

Welcome to the world of modern auto repair where the vehicle manufacturers go to GREAT LENGTHS to keep you from figuring out these thing for yourself an FORCE you back into their dealerships for repairs......A whole other subject that really eats my craw!

Please also check out this link: Right To Repair

Jun 02, 2012 | 2008 Volkswagen R32

1 Answer

My cigarrette lighter shorted out now my fog lights will not work.


Hello! Accidental short on the cigar lighter or a failure? If it was a failure has the cigar lighter socket been replaced and is OK? If the failure or accidental short on the cigar lighter happened when the fog lamps were on current back fed through the Fog Lamp Relay and may have damaged its contacts...Question then becomes; Is the fog lamp fuse (FOG LPS 15 A) OK...it is in the under hood fuse block..Have you checked the fog lps fuse? if it is good and fog lamps do not come on replace the Fog Lamp Relay (under hood fuse/relay block)
Guru...saailer

Dec 13, 2011 | 2002 GMC Yukon Denali

1 Answer

Looking for fuse for fog lights on a 2008 dodge charger. we installed a fog light kit. the car is pre-wired for them. we replaced the head light switch with the one from the kit. fog lights arent...


Check your instructions with the fog lamps, I believe you will need to take your car to a dealer to have them activate the fog lamp driver in the Totally Integrated Power Module.

Jan 23, 2011 | 2008 Dodge Charger

2 Answers

My fog lights are not working, the relay is fine but not sure where the fuse is? Don't want to buy a service manual for this one simple thing. It does not tell you in the manual.


I have a 2004 f150 xlt triton. I couldn't figure out the how to turn on the fog lamps and the manual was not helpful.

Solution: turn the light switch all the way to the right and pull the switch (out) towards you. Push switch in and it turns off. The manual says to turn switch all the way to right but doesn't say to pull switch out.

Aug 25, 2010 | 2004 Ford F150

1 Answer

How do I replace the fog light assembly on a 2000 Olds Alero?


you replace the fog lamps by going under front bumper fascia.remove the pushpins and take down the splash shield to access the back of the fog lamps.then you remove two bolts retaining the fog lamp to the back of front bumper.besure to wear clean gloves.because fog lamps is halogen bulbs.if you touch with bare hands the oils from hands will make the bulbs over heat and blow out.

Dec 03, 2009 | 1999 Oldsmobile Alero

1 Answer

Lights


FROM: Lusty Kid:

Your fog lights should not work with high beam... they should work with the low beams. they are connected wrong, which probably drew too much current through the light switch burning out the contact points for the parking lights in the switch

Start by Fixing the fog light connections to work with low beams. Appears to me this was not factory installed. Aftermarket kit maybe! Then see if your parking lights work. If parking lights don't work still and everything else works, replace the light switch $50 at the dealer. The switch works the fog lamps when you pull out the knob to turn on the fog lamps when the lights are turned on. When the fogs are on you will see a little amber light to let you know your fogs are on. When you switch to high beam the fog lamps go off. Again if its not working that way, then is wired wrong. Needless to say, there should be connectors in the harness of the lights for the fog lamps. Use those if possible with the kit that you can get at the dealer, or you can splice the connector with those blue splicing clips sold at the auto part store. Make sure ground is ground when splicing and water proof the connection sith silicone and tape.

Dec 13, 2008 | 2004 Ford F150

Not finding what you are looking for?
2004 Toyota Camry Logo

635 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...