Question about 1996 Buick Century

1 Answer

Changing thermostat hard to get to any tips or tricks for changing

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Make sure car is cool its right by exhust,you may want to buy a stubby 13mm wrench,make sure when you pull housing off use a screwdriver to hold thermostate in place its the only way to get housing out with out removing exhust.good luck

Posted on Jan 15, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is it an easy job to change the thermostat on a Mitsubishi Express Van 2004. I was told it was at the end of the top radiator hose. My sons car has broken down are there any tricks I should know.


Loosen the upper radiator hose. This is the hose that connects to top of the radiator to the engine. Loosen the hose on the end that connects to the engine by using a flat-tip screwdriver to loosen the circular clamp.

  • Remove the hose. Pull the upper radiator hose off the end that connects to the engine. Have a drain pan underneath the hose to catch any coolant that remains in the hose.

  • Loosen the thermostat housing. Use your ratchet and socket set to loosen the bolts that hold your Mitsubishi's thermostat housing in place. The number of bolts and their locations vary based on your Mitsubishi model

  • Dec 02, 2016 | Mitsubishi Cars & Trucks

    1 Answer

    I bought a 95 Camaro z28 with a lt1 v8 and I just changed alot of sensors and the water pump, pcv, thermostat, gauge sensor ,all the cooling hoses ,spark plugs and wires ,new opti-connector,fans are...


    Did you burp the air out of the cooling system? That needs to be done if you haven't - air will trap the thermostat and keep it from opening. Check my tips and tricks for how to do this.

    Jul 15, 2011 | 1995 Chevrolet Camaro

    1 Answer

    Cooling system overheating


    Click my screenname, go to my tips and tricks, and you'll find the procedure there - it'll walk you right through it.

    Jan 24, 2010 | 1999 Chevrolet Cavalier

    1 Answer

    My car becomes hot after awhile driving


    Before you do that, after you changed the thermostat, did you bleed tge air out of the system? If not, you'll still overheat. Click my screenname, go to my Tips and Tricks, and follow the procedure there for burping the cooling system and see if that fixes your overheating problem.

    Jan 22, 2010 | 1993 Toyota Previa

    1 Answer

    Fluctuation engine temperature interior heat stops when engine temp goes up. engine makes clatter noise at times


    Getting P0135 and P0301 also in this Montana. I'm guessing its the upstream O2. (bank 1, sensor 1)

    Changed the thermostat, and the oil and antifreeze is clean and clear.

    Any tips or tricks on how to tilt engine to change O2?

    Dec 28, 2009 | 2001 Pontiac Montana

    1 Answer

    Overheating


    Did you burp the cooling system after you changed the thermostat and topped off the coolant? If not, click my screenname, go to Tips and Tricks, and follow the procedure there that I've written up. If this wasn't done, it'd be a very easy reason why you still overheat.

    Dec 14, 2009 | 1997 Chrysler Sebring

    1 Answer

    How to replace a thermostat on a 1993 dodge cARAVAN


    Follow the lower radiator hose back from the radiator to the engine. Where it attaches is the thermostat housing. Open that up, remove the old thermostat, put the new one in (there's a small bleed valve on the face of the thermostat -that needs to be at the 12 o'clock position), reassemble, and then burp the cooling system (click my screenname, go to Tips and Tricks, and follow the burping instructions there).

    Dec 11, 2009 | 1993 Dodge Caravan

    1 Answer

    Overheating


    Click on my screenname, go to the Tips and Tricks, and read my Tip about burping the cooling system - sounds like it's perfect to solve your problem.

    Dec 10, 2009 | 1992 Toyota Paseo

    Not finding what you are looking for?
    1996 Buick Century Logo

    Related Topics:

    110 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Buick Experts

    yadayada
    yadayada

    Level 3 Expert

    70346 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22041 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6869 Answers

    Are you a Buick Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...