Question about 1993 Ford Ranger SuperCab

1 Answer

Where is the power steering sensor located on a 1993 ford ranger 4.0 super cab? (or is it called the power steering pressure switch?)

Posted by on

  • Anonymous Nov 25, 2008

    yes, i am having the same problem locating this sensor (switch).  after reading your description of its location, i am still unsure as to where to locate it. is there a diagram or photo i can refer to?


    thx,
    jack

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 94 Answers

The power steering pressure switch as its called threads in to the power steering pressure hose most of the time it is close to the power steering pump, I have also seen them at the lower point of the pressure hose close to the rack and pinion.

Posted on Nov 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1994 Ford Ranger Super Cab MAF problems


Looks like you need to replace the coolant temperature sensor for the computer. This will make the engine run rich all the time. You can simply check it with a scan tool with live data capability. With the engine warm read the engine coolant temperature. My guess is it will read very cold even with the engine warm. If so replace it and the truck will be running like new

Jul 19, 2014 | 1994 Ford Ranger Supercab

1 Answer

Where is the temperture sensor and sender is located on 2003 ford ranger/2.3


had a ranger never had that problem just call Auto Zone they'll look it up for you I have a book just too lazy to find it. Plus mine was 4.0

Jul 28, 2012 | 2003 Ford Ranger Regular Cab

1 Answer

1993 ford ranger blinkers not working


first check fuse if fuse okay the turn signal lights dont work and flasher dont work problem could be faulty turn signal switch or faulty hazard flasher.which locate on fuse panel under instrument panel to the left of the steering column.

Nov 28, 2011 | 1993 Ford Ranger SuperCab

2 Answers

I have power steering fluid leaking from the sensor's plug-in to the power steering pump. Where the 2 wires connect into the housing. Is it the pressure sensor? If so, how do I fix it?


TO REPLACE THE POWER STEERING PRESSURE SWITCH.REMOVE SIPHON OUT POWER STEERING FLUID BELOW THE PRESSURE SWITCH.UNSCREW THE OLD PRESSURE SWITCH AND SCREW IN THE NEW POWER STEERING PRESSURE SWITCH.MAKE PRESSURE SWITCH HAS THREAD SEALER ON IT.IF NEW PRESSURE SWITCH THREADS ALREADY HAVE SEALER ON THE THREAD DONT NEED TO USE TEFLON TAPE TO SEAL THE THREADS.BLEED POWER STEERING SYSTEM.

May 09, 2011 | 2001 Ford Escape

1 Answer

Were is the flasher on a ford ranger


2001 Ford Truck Ranger 2WD 4.0L EFI SOHC 6cyl:
The Flasher is located in front seating area, behind steering column cover, on left hand side of steering column.

Hope helps with this. Good luck.

Dec 29, 2009 | 2001 Ford Ranger Regular Cab

1 Answer

2000 ford ranger super cab won't start clicking


Could be corrosion on the cables, I would clean both cables and try again. if no corrosion I would then look at the battery for correct voltage and fluid. batttery could be bad.

Oct 26, 2009 | 2000 Ford Ranger SuperCab

1 Answer

My 1993 Ford Ranger Super Cab 3.0 L will suddenly start bucking and running very rough and will only reach a maximum speed of 25. You can shut off and leave set 3 to 4 minutes and runs normal. If you...


Have the idle air control valve looked at. There have been many issues with them. They get dirty and wont allow the pintle at the end of it to seat properly.

Aug 10, 2009 | 1993 Ford Ranger SuperCab

2 Answers

Cranks but won't start,new fuel pump,no power going to pump


look at inerata reset switch check for power at the switch

Jun 23, 2009 | 1993 Ford Ranger SuperCab

2 Answers

Where & how many oxygen sensors do I need for my 1997 Ford Ranger XLT Super Cab


Look before and after the catalytic converters. They will have wiring connected to them.

Apr 20, 2009 | 1997 Ford Ranger SuperCab

Not finding what you are looking for?
1993 Ford Ranger SuperCab Logo

Related Topics:

516 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...