Question about 2006 Chevrolet Cobalt

1 Answer

How to remove inner window crank on 2006 chev cobalt 2 dr

I am removing my door panel on my 06 cobalt to replace the oem speakers. i am having trouble getting the window crank off. can you help me?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 61 Answers

The handle part of the crank is held on by a small ring, you will need a small flat head screw driver- i used a butter knife, as it works better- push the door panel back just enough you can see behind the round part of the handle, you should be able to see the foot of the clip, push it off, make sure you don't do this in the grass, the ring will roll when it falls off. **please note this is a flat ring and only about the diameter of your little finger**

Posted on Nov 25, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to remove door panel with a manual window


screws in the armrest, clip on window crank, screw behind door handle and possible a screw behind a plug that is located to the inner or outer pane, then with a flat tip screwdriver gently pry around the outside of the panel then lift panel up and out. Good Luck Tim

May 22, 2011 | 2001 Dodge Dakota

1 Answer

How do u remove the drivers side door panel to fix the window


YOU NEED CLIP REMOVAL TOOL TO REMOVE WINDOW CRANK HANDLE.YOU NEED DOOR PANEL FLAT TOOL REMOVE DOOR PANEL HATE TO SAY DOOR PANEL HAS AT LEAST 8 CLIPS LOCATIONS 4 CLIPS AT THE BOTTOM PANEL 2 CLIPS ON BOTH SIDES DOOR PANEL. YOU HAVE TO REMOVE 2 SCREWS HOLDING DOOR PULL CUP.YOU HAVE RELEASE CLIP BEHIND DOOR HANDLE USING TRIM TOOL.IF YOU HAVE TROUBLE GETTING DOOR PANEL OFF.HAYNES REPAIR MANUAL CAN HELP.

Oct 07, 2010 | 2004 Chevrolet Cobalt

1 Answer

Inside door handle R&R 06 fusion


Not too bad a job to do, taking your time it should take 30-45 minutes. You will need a straight screwdriver, phillips screwdriver, a small set of sockets, a clip removal tool also comes in handy.

If you have manual windows, you will need to remove the clip holding the window crank in place. Usually the clip removal tool makes easy work of it by just pushing the clip out from under the window crank handle. If you have electric windows so much the better.

Roll down the window before beginning. Now depending on how Detroit was hiding things, you should look in the area of the door pull for screws that fasten the interior door covering to the door. These might be exposed but sometimes are hidden under plastic caps or trim parts. Very carefully remove this pieces as with age they do become brittle.

Once you are rather sure you have the fastening screws out of the way, using the straight screwdriver to ease the door panel away from the door along the bottom edge. By looking inside you should see one of two methods of fasteners. The older style are simply straight push in plastic clips, you release these by simply putting enough pressure of the panel to pull the clips out. The newer method has a clip that slides down about a 1/2 inch into a matching hole. These panels are removed by lifting up on the door panel and then out.

With the panel off, you can now remove and replace the inner door handle, not much to them usually a couple of clips holding the connecting rod(s) and 3-4 bolts.

Installation is just a reversal of the removal procedure.

May 03, 2010 | 2006 Ford Fusion

1 Answer

Passenger door removal for radio speaker access.


YOU NEED A DOOR PANEL FLAT TOOL AND WINDOW CRANK CLIP TOOL IF YOU DONT HAVE POWER WINDOWS. A HAYNES REPAIR MANUAL TO SHOW YOU HOW TO REMOVE DOOR PANEL.

Apr 04, 2010 | 2007 Chevrolet Cobalt Coupe

1 Answer

How to remove the inside door panel from a dodge 2005 2500 pick up


FRONT DOOR TRIM PANEL - REMOVAL
Release door latch and open door.
Roll window down.
Remove window crank Window Crank - Typical , if equipped.
Remove screws attaching trim panel to door Door Trim Panel and Trim Panel Screw
CAUTION: Do not forcibly pull trim panel from door, damage to trim panel may occur.

Simultaneously lift upward and outward to release retainer steps from inner door panel Trim Panel Retainer
Disengage inside handle linkage rod from inside handle.
Disconnect speaker harness wire connector Speaker And Power Mirror Connector
Disengage power mirror wire connector, if equipped (driver's side only) Speaker And Power Mirror Connector
Disengage clips attaching power window/lock switch panel to door trim panel. Disengage wire connector from switch panel, if equipped Power Door Lock/Window Connector
Separate door trim panel from vehicle.
INSTALLATION
Position trim panel at door.
Engage wire connector for window/lock switch panel, if equipped. Engage clips attaching power window/lock switch panel to door trim panel.
Engage power mirror wire connector, if equipped.
Connect speaker harness wire connector.
Engage inside handle linkage rod to inside handle.
Align trim panel retainer steps with inner door panel and slide trim panel into place.
Install screws attaching trim panel to door.
Install window crank, if equipped.

Hope helped with this; remember rated this help. Good luck.

Nov 12, 2009 | 2005 Dodge Ram 2500 Truck

2 Answers

It there a access door to the fuel pump under the back seat of a 06 cobalt?


You'll need to drop your tank in order to get the fuel pump

Sep 28, 2009 | 2006 Chevrolet Cobalt

1 Answer

How do I replace a '94 chev Astro outside drivers door handle


You first have to remove the inner door panel by taking the screws out of the inner handle and arm rest. the outer edges of the inner door panel either has screws or it has clips that can be pulled out. after you remove the panel you need to roll up the window and you will be looking at the back of the handle. simply un hook the clips that hold the lockrod and the inner opener rod and unbolt the outside door handle. reverse the prosses and walla.

Sep 19, 2009 | 1990 Chevrolet Suburban

1 Answer

Want to install after market speakers in 06 Chevy Cobalt...


they make a tool V-shaped that should be used for prying around the door panel..door airbags should not be triggered unless wiring for them is shorted, replacing speakers should not mess up any other wiring , fuses should be fine as are..

Jun 02, 2009 | 2006 Chevrolet Cobalt

2 Answers

How to get the window crank off on 2dr 06 cobalt


there is a clip behind the handle. you should see something like a big plastic washer between handle and panel, the clip is between this washer and handle use a pick to get clip off

Nov 25, 2008 | 2006 Chevrolet Cobalt

1 Answer

Inner door panel


There is a U clamp between the panel and handle.

Jul 07, 2008 | 2006 Chevrolet Cobalt

Not finding what you are looking for?
2006 Chevrolet Cobalt Logo

875 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6879 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...