Question about 2003 Dodge Stratus

1 Answer

Cam sensor Is it easy to replace the cam sensor?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 90 Answers

Yes, it's on the rear of the cylinder head. 4 bolts and a electrical connector.

Posted on Jan 27, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

04 terracan wont start changed cam sensor as would start with easy start spray now wont start

If the engine started with easy start spray, it was getting spark. Why did you change the cam sensor? You need to find out why the engine is not getting fuel (fuel pump, filter, injectors, etc). If it doesn't start at all now, even with easy start spray, you may want to put your original cam sensor back in. Do you have a check engine light? Any codes? Don't just change parts hoping for results - troubleshoot the issues!

Jan 28, 2017 | Cars & Trucks

3 Answers

Code p1391, ckp or cmp sensor intermittent

Its the crank and or the cam sensor , But the the CAM sensor should fix this.. But check and be sure wiring to sensor is ok. God-Bless!

Apr 02, 2016 | 2000 Dodge Intrepid

1 Answer


on a 4 cyl is very easy, Nissan recommends replacement of both the crank and cam sensor together, but the crank sensor is in the back of the engine, near the transmission bell housing under the engine mount bracket. the cam sensor is in the back of the cylinder head and both have 1 bolt each, 10mm.

Nov 06, 2014 | 2004 Nissan Sentra

1 Answer

Cam shaft position sensors

In my 3.5L HO cps is located front top left, just under edge of upper intake manifold, maybe an inch and a half aft of timing cover. I replaced mine, easy enough.

Jan 02, 2014 | 2004 Dodge Intrepid

1 Answer

Vauxhall vectra 2006 cam sensor

I have had this before it is best to change the cam and crank sensors as a pair. as a week sensor will affect the other sensor.and give a false code. as these work together. it is best to change both at the same time. i changed the crank on mine after the cam and it sorted it out. crank sensor is located near to the thermostat and under the exhaust manifold. make sure you tuck the wire away from the exhaust manifold . other end of the wire is fitted to the under neath of the injector cover and is cliped in place very easy to replace

Jul 27, 2013 | Vauxhall Cars & Trucks

3 Answers

My 2004 Taurus has chirping sound in motor.Not belts.Other end of motor.Could it be cam position sensor?

YES. Very common problem. The cam sensor driver unit goes bad. (Usually called a "Cam Syncronizer") Squeeks like crazy, causes hard starts, poor fuel mileage, usually destroys the cam sensor itself, and will cause catalytic converter damage if not fixed promptly. (You will find broken, rusted pieces inside the assembly if you take the sensor off of the top)
Complete kits (Made by Dorman) are available at most parts retailers. It will look similar to this:

dttech_10.jpg It should be noted that although this part is relatively easy to replace, it can also be very easy to install it incorrectly. Proper alignment (Syncronization) should be checked using a scan tool after installation.

Apr 24, 2011 | 1999 Ford Taurus

1 Answer

Where is renault megane 1600 cam shaft sensor (the small one)

cam sensor is black sensor next to coil no1 need to remove coil for access to sensor. no1 is gearbox side.

Mar 02, 2010 | 2004 Renault 181

1 Answer

Cam position sensor broke

ok easy fix. this is common on ALL ford w this style cam sensor,3.0 eats them for lunch. the sensor base has bushings like a real distributor, they get wore and fail. you can get new from ford, or reman at auto parts about 100 bucks. they come w the sensor installed but as with either, you need the allginment tool, looks like a little hockey puck, that only come from ford to set up or check engine light wont shut off. it will run without this but poorly. if you need more advice just post a comment to this and ill do my best to advise you

Sep 03, 2009 | 1998 Ford Explorer

1 Answer

I have a 2001 dodge 24 valve diesel and need to replace the cam shaft sensor, i bought the sensor but cant find where it is on the motor. where is the cam shaft sensor located on the motor?

it is located below the fuel injection pump in timing gear housing..not easy to get at..1 bolt and electrical connector..goes in from behind into housing..injector pump is unit with all the fuel lines coming out of it..have replaced these sensors before

Apr 30, 2009 | 2001 Dodge Ram 3500 Truck

2 Answers

Crank sensor

The crank sensor is behind the harmonic balancer. Not too hard to replace, the harmonic balancer is supposed to come right off but I needed a big 2-jaw puller to get it off.... accessed through the wheel well.

Jul 11, 2008 | 1992 Oldsmobile 88

Not finding what you are looking for?
2003 Dodge Stratus Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides