Question about Jeep Commander

1 Answer

Need to chnage a brake lamp in my Jeep Commander 2006. How do I get to them?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 324 Answers

You have to pull the uinside panel off behind the lights, and there is some quick screw nuts on them, it will then pop right out.

Posted on Nov 26, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake lights pop off and on all other lights work 2006 jeep comander 5.7 V.8 hemi please advice could it be a switch


rear blake lamps
or cluster warning lamps maked brake and or ABS.
PLEASE ELABORATE
POP ON /OFF????
Tell what works and not work, lights
be clear
all 3 rear brake lamps dead?
2 are 1 is not.or?
does car drive ok?
does shift'er lever move from park to drive.????

Feb 20, 2017 | 2006 Jeep Commander

1 Answer

Brake lights pop on and off . all other lights work 2006 jeep comander limited edition 5.7 hemi please advise


double posted
;please add to one post.
and answer the question there.
all brake lamps pop on, with foot on brake all 3 on rear of car.
does car drive ok.
held lamps bright,
heater bower work on high,sounding OK?

Feb 20, 2017 | 2006 Jeep Commander

1 Answer

Turn signal stays on a2006 jeep commander


Your turn signals are controlled by a electronic control module .The integrated power module . The switch is off an the turn lamp stays on ? No Low Beam Head Lamp Chrysler Pacifica Check out this guy's video , I know it's no same vehicle as yours ,but it's a Chrysler an jeep is the same manufacture. Chrysler Pacifica TIPM Electrical Problems .

Nov 30, 2015 | 2006 Jeep Commander

1 Answer

JEEP COMMANDER REAR BRAKES DRUMS OR DISC?


It has both. the emergency break is a drum brake, under the inner portion of the rotor

May 12, 2014 | 2006 Jeep Commander

1 Answer

Brake lights stay on running or not, lights on or off for 2006 Jeep Commander. How do I get them off? What is causing this problem?


The problem is likley caused by a defective brake light switch, it is located under the dash above the brake pedal arm, you must remove any under dash covers to see it.

Feb 13, 2012 | 2006 Jeep Commander

1 Answer

My 06 jeep commander makes a noise like brakes dragging when backing up first thing in the morning.


thasts because they are possibly dragging and to find it you would need to jack vehicle up and turn each wheel in turn ,it could be anything from a piston in a brake caliper to the handbrake shoes which are inside the rear brake disk

Aug 10, 2010 | 2006 Jeep Commander

1 Answer

What number of fluid brakes uses Jeep Commander: Dot 3 or Dot 4 ?? Thank for your assistance, Carlos


the higher the number the better the brake fluid is ,you can use either,dot 4 is the newest out there,it resist moisture more than dot 3

Jan 24, 2010 | 2006 Jeep Commander

1 Answer

Jeep Commander Rear Brake Pad Installation


Per Chilton Auto repair manual:

Removal & Installation
  1. Raise and safely support the vehicle.
  2. Remove the rear wheel.
  3. Siphon a small amount of brake fluid from the master cylinder reservoir.
  4. Insert a small prybar through the caliper opening and pry the caliper cover (using the outboard brake pad) to bottom the piston in the caliper bore.
  5. Remove the caliper slide bolts.
  6. Remove the caliper from the anchor.

    WARNING Support the brake caliper with mechanics wire. Do not let the caliper hang by the brake hose.
  7. Remove the brake pads from the caliper.
To install:
  1. Install the brake pads onto the caliper.
  2. Lubricate the slide pin bolts with grease provided with the brake pads, or suitable silicon grease equivalent.
  3. Install the caliper on the anchor and tighten the slide pin bolts to 18 ft. lbs. (25 Nm).
  4. Install the rear wheel.
  5. Lower the vehicle.
  6. Pump the brake pedal several times until a firm pedal is obtained in order to properly seat the pads.
  7. Refill the brake fluid reservoir to the proper level.

May 17, 2009 | 2006 Jeep Commander

1 Answer

Brake problems


the front rotors are warped,they need to be replaced

May 15, 2009 | 2006 Jeep Commander

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

74544 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7268 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...