Question about 1999 Lexus RX 300

3 Answers

How to replace side light bulb lexus rx300 - 1999 Lexus RX 300

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Remove 3 - 4 screws on fender cover close to side marker light. Pull fender cover out a bit for you to use your other hand to reach side marker light. By twisting on one direction and here you go the light out. Replace new bulb and replace everything in reverse order.

Posted on Aug 18, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Lexus Master
  • 1,564 Answers

There should be 2-3 bolts behind a pop-out inner panel. Remove the nuts from these bolts and aplly a forceful push on the lens housing, NOT near the bulb sockets for this area is to weak. The whole assembly should pop off. If not take a butter knife(non serrated) and work it in behind the outer seal all the way around. Good luck! Dana

Posted on Aug 18, 2009

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 30 Answers

Get to these through the bottom remove the 10mm bolts securing the forward portion of the inner fender liner.

Posted on Jun 16, 2009

5 Suggested Answers

keithheavili
  • 410 Answers

SOURCE: ? to Replace Timing belt on 2000 Lexus Rx300 with 57,000 miles.

If it is running perfectly I wouldn't think that you would need to replace the timing belt. You shouldn't need to replace that until 100,000-120,000 miles. I would definitely hold off until now unless you have start having some timing problems. Let me know if you have any other questions. Thanks for rating my response and for using FixYa!

Posted on Jul 08, 2009

  • 17 Answers

SOURCE: Replace front side running light in a 2000 Lexus RX300

Unscrew 3 - 4 screws on the front tire fendor cover close to your side marker light. Pull the fender cover out, use your other hand to reach the side marker light. Using twist and pull the light set out. Replace a new light bulb. Replace everything in a reverse order.

Posted on Aug 18, 2009

  • 17 Answers

SOURCE: replace side marker light on lexus rx300

Remove 3 - 4 screws on fender cover close to side marker light. Pull fender cover out a bit for you to use your other hand to reach side marker light. By twisting on one direction and here you go the light out. Replace new bulb and replace everything on reverse order.

Posted on Aug 18, 2009

  • 17 Answers

SOURCE: Replacing outer tail light on Lexus RX300 ?

Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-fareast-font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Lift the hatch. The tall center light is located behind the upper hatch inside panel. There are two panels need to remove. One panel is on the right, the other on the left. To remove the panels you have to use flat screw driver to pry out the panel in several locations. (These panels are secured by several small metal clips.) Be careful to collect all these clips and replace them on the back of the panel. You will need these clips to replace the panel later on. After remove the panels, you will be able to locate the screws on the tall center stop light assembly. Remove those screws and cover. After replacing light bulb. Assemble everything in reverse order. Remember, the metal clips have to set on the back of the two panels not the car body.

Posted on Aug 18, 2009

Murphybanton
  • 2004 Answers

SOURCE: Lexus RX300 engine light n VSC light comes on

VSC means Vehicle Stability Control.

It comes on when the sensor send a signal that the vehicle is not stable on the ground.....check the wheel balancing and alignment and the air pressure of your tires too.

Good luck.

Rate this solution.

Posted on Aug 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver side suspension drops when turned off works ok with engine running new sensor fitted still has problem


RX300 Mega Thread. Start here if you have a problem - Club Lexus ...

www.clublexus.com/.../679100-rx300-mega-thread-start-here-if-you-ha...
Feb 17, 2013 - One question per post please. ... manual-search, just enter RX300 or whatever Lexus vehicle and year ... Side affects of CEL: Based on the error code, your RX may end up in a .... You may hear a drop in rpm of the donor car. Window Switch Problems Pass side
Jul 17, 2015
RX300 knock sensor replacement DIY
Jul 6, 2015
RX300 (year 2004) air suspension fault

Jul 17, 2015 | 2003 Lexus RX 300

1 Answer

How to get to the light bulb on rear hatch of 2001 rx300


LOOK IN GLOVE COMPARTMENT IN THE OWNERS MANUAL.LOOK IN THE BACK INDEX FOR BULB REPLACEMENT.IT WILL SHOW AND TELL YOU HOW TO REPLACE REAR BULB.

Jun 19, 2011 | Lexus RX 300 Cars & Trucks

1 Answer

The passenger side blinker on my 2002 lexus rx300 does not work. The bulbs are fine but the blinker is out. How can I fix this


buy a test light ($5)
turn passenger side blinker on
place clip of test light on a good earth
use test light to check for power to the bulb
if no power is found you will have to check for power at the blinker assembly inside the car
if you find power at the bulb but the bulb doesn't flash you may have a bad earth

Jun 28, 2010 | 2002 Lexus RX 300

1 Answer

Brake lights still aren't working on my 2000 Lexus RX300. Changed fuse, bulbs, and switch. What's next?


Make sure you have 12V when the switch is engaged first to ensure the electrical path is working, then the rest could be diagnosed systematically. Did the fuse burn so you could replace or you just replace for the sake of it? Did you measure the bulb continuity before tossing it away? Sometimes the oxidation on the bulb holder causes bad contact so light can't be on. Cheers

Jun 25, 2010 | 2000 Lexus RX 300

1 Answer

I have a light that is attached to the body (not the hatchback) on the right rear of my lexus rx300 How do I access this to change the light bulb


if you mean the one that is on the rear bumper side just reach up inside and twist and the socket will come out

Dec 31, 2009 | 2000 Lexus RX 300

1 Answer

Replace side marker light on lexus rx300


Remove 3 - 4 screws on fender cover close to side marker light. Pull fender cover out a bit for you to use your other hand to reach side marker light. By twisting on one direction and here you go the light out. Replace new bulb and replace everything on reverse order.

Jul 25, 2009 | 2000 Lexus RX 300

1 Answer

Replacing outer tail light on Lexus RX300 ?


Normal 0 false false false MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman"; mso-fareast-font-family:"Times New Roman"; mso-ansi-language:#0400; mso-fareast-language:#0400; mso-bidi-language:#0400;} Lift the hatch. The tall center light is located behind the upper hatch inside panel. There are two panels need to remove. One panel is on the right, the other on the left. To remove the panels you have to use flat screw driver to pry out the panel in several locations. (These panels are secured by several small metal clips.) Be careful to collect all these clips and replace them on the back of the panel. You will need these clips to replace the panel later on. After remove the panels, you will be able to locate the screws on the tall center stop light assembly. Remove those screws and cover. After replacing light bulb. Assemble everything in reverse order. Remember, the metal clips have to set on the back of the two panels not the car body.

Jul 04, 2009 | 2002 Lexus RX 300

1 Answer

Replace front side running light in a 2000 Lexus RX300


Unscrew 3 - 4 screws on the front tire fendor cover close to your side marker light. Pull the fender cover out, use your other hand to reach the side marker light. Using twist and pull the light set out. Replace a new light bulb. Replace everything in a reverse order.

Mar 18, 2009 | 2000 Lexus RX 300

2 Answers

How do I change the brake lights on my 1999 Lexus?


If it's the same as the 1995 lexus, you go through the trunk.

Unscrew the bolts that are holding the brake lights in place through the holes in the apolstry in the trunk. The light should come loose and from there find which wire goes to the bulb that's out. Unscrew the piece, pull the bulb out, and replace.

Jul 31, 2008 | 1998 Lexus Sc 300

Not finding what you are looking for?
1999 Lexus RX 300 Logo

2,914 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...