Question about 1997 Oldsmobile Aurora

1 Answer

How do I change the bulb in my driving lights

Could you please tell me how to change the bulbs in my driving lights. There doesn't seem to be an way to get in from the back.
Thanks

Posted by on

  • nwestbrooks Dec 19, 2008

    the dash board doesnt come on my 97 oldsmobile aurora

  • Anonymous Feb 17, 2009

    How do I change the bulb in my driving lights on 1996 olds aurora

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

Do you mean your headlight bulbs? if so you have to take out the air filter assembly on drivers side and you can just barley get enough hand clearance to reach in there...other side is same...its not easy to do

Posted on Dec 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Passenger side driving lights not working on 2001 saab 9-3


Are you sure the bulbs are ok.Visually it's hard to tell. all the time if they are bad. Be sure and check them with a meter and if they check out ok then you need to check for voltage with the key in the on position and lights on.going to the rear light assembly itself. Usually if its just one side not working it's a bad bulb. But that's usually not always. Good luck.

Mar 05, 2014 | Cars & Trucks

1 Answer

Reverse Light doesn't work, fuse good and bulb to.


I haven't worked on an escape, but i can tell you that switch is on the transmission.

Jun 02, 2013 | 2010 Ford Escape XLT

1 Answer

Mazda cx7. both high beams work and one low beam works. how can i tell if its a headlight or some other problem


Thanks for choosing FixYa and welcome. These new lights have two types lin one bulb, one for the low beam and one for the high beam. Find the bulb that isn't lighting for the low beam and replace it with a new bulb. If it doesn't work, you need to check the wiring to that specific light. Since it is only one, the new bulb should work.

Oct 01, 2011 | 2000 Mazda MPV

1 Answer

The yellow light telling you the last gallon of fuel doesn`t light up I already change the little bulb, but still doesn´t work. What can i do?


never seen one go out,must be driving on empty alot,check fuses,if you have power to the light then your instrument cluster could be bad.









TIM..........

Oct 22, 2010 | 1995 Honda Accord

1 Answer

My dashboard main light went out. I don


check the fuses if not the fuse its the bulb

May 17, 2010 | 2006 Jeep Liberty

1 Answer

Please tell me how to replace a burned out head light, high beam.


To replace the headlamp, turn signal, or parking lamp bulb:This information should be in your owner's manual.
Turn the wheel to access the wheel well.
  1. Remove the fasteners located on the wheel liner. To access the headlamp and the turn signal/parking lamp bulbs.
  2. Reach in behind the wheel well liner and locate the bulb to be changed.
  3. Turn the bulb socket counterclockwise and pull it straight out of the lamp assembly.
  4. Pull the old bulb straight out of the bulb socket.
  5. Push the new bulb straight into the bulb socket until it clicks.
  6. Push the bulb socket straight into the lamp assembly and turn it clockwise to lock it into place.
  7. Reinstall the wheel well liner using fasteners.

Nov 11, 2009 | 2006 Chevrolet HHR

1 Answer

Fog/driving light bulb replace


There is a panel under the corners of the bumper that is held by two screws. You can access the Light bulb by removing the panel, careful that when installing the new bulb's. Try to keep from touching the glass and it's a go thing to change both side. Good luck

Mar 14, 2009 | 2003 Pontiac Montana

1 Answer

How to change tag lights


I had to remove the entire light bar assy by taking every bolt loose to gain access to replace the tag bulbs on my 2000 Buick Lesabre. It is necessary to replace only one bulb so I replaced all bulbs with the new longer lasting bulbs...the bulbs are not expensive just impossible to gain access to them one at a time. It seems like GM made it so you would have to take it into the GM Dealer. A deep well socket makes the task muck easier! Hope this helps!

Jan 07, 2009 | 2000 Buick LeSabre

Not finding what you are looking for?
1997 Oldsmobile Aurora Logo

Related Topics:

112 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...