Question about 1989 GMC K1500

2 Answers

Turn signals don't work

The tail lights and hazard flashers work. There is power to the fuse in the fuse panel. I have replaced the turn signal switch in the steering column. Older vehicles had 2 circuits. 1 for hazards, 1 for turn signals. I am not sure whether this has 2 circuits or not but I can only find 1 flasher relay and it is wotking with the hazard flashers. Is there a relay on the fuse box that is for the turn signals but does not look like the hazard relay. NAPA says the turn signal relay and the hazard relay are the same type but don't say whether there is one or 2 in the circuit..

Posted by on

  • FRYNTYR Apr 12, 2009

    I have the same problem and have not found another relay yet. Hazard flashers work but nothing on the turn signals, nothing even comes on.

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

I have a similar problem but my left signal works, when i turn the right on it just does an annoying buzz sound. if you can think of any explination for such shinanogins help would be greatly appreciated

Posted on Apr 26, 2013

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 99 Answers

You should have a flasher for the turn signals as well as one for the hazard flashers turn signal flasher can be in fuse box on drivers side or mounted to steering column

Posted on Nov 30, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 buick century turn signal not flashing but bulb comes on


Do the hazard light's work ? Did you try replacing the turn/ hazard flasher ?
Remove the LH instrument panel (IP) insulator. Refer to Instrument Panel Insulator Replacement in Instrument Panel, Gauges and Console.
Remove the steering column filler panel. Refer to Steering Column Opening Filler Replacement in Instrument Panel, Gauges and Console.
Grasp the hazard and turn signal flasher and slide the flasher to the right to release the flasher tabs from the slots on the BCM bracket.
Disconnect the electrical connector from the hazard and turn signal flasher.

Hazard Lamp/Turn Signal Lamp Flasher
Below left side of the IP, mounted on the multipurpose bracket, near the BCM

Oct 14, 2017 | Buick Cars & Trucks

1 Answer

How do i find the talight relay sensor for a 1997 chevy cavalier


No such thing , tail lights get power from headlamp switch . When you turn on park or head lamps . tail lights light up . License plate lights come on as well as side marker lamps . Unless you thing of the turn signals an hazard lights . There is a flasher relay for that .
Turn/Hazard Flasher
At the left lower instrument panel, near the steering column

Aug 16, 2015 | Cars & Trucks

1 Answer

Where is on 1987 pontiac 6000 are the bulbs for turn signals How do I get to them? & or the flasher ? Is it in the fuse box?


The turn signals at the rear share the same bulb, same filament on the bulb even, as the brake lights. So if you have brake lights, the rear turn signal bulbs are good. If I recall, you access the rear bulbs from inside the trunk, and pretty easy to change bulbs. Look for a panel or trim piece in the trunk that covers the light bulb assemblies. You turn the bulb sockets a quarter turn counter-clockwise and pull them out, then you can replace the bulbs. They are two filament bulbs-one filament for the park lights (tail lights) and one filament that serves for brakes and turn signals together.
The flasher unit is a small round cylinder, I don't believe it was in the fuse box, but located up under the dash, close to the steering column. The hazard flasher unit was also up under there and looks the same. Look for them on a bracket near or by the steering column, possibly one on each side of the steering column To find the turn flasher, turn your hazard switch on. The little round unit that is clicking-you may hear it or feel it click with your finger on it-is the hazard flasher. The turn flasher will be the one that is not clicking. A little round cylinder is how you identify it.

Jun 03, 2014 | Cars & Trucks

1 Answer

Where is the flasher relay on a 2002 monte carlo


It's part of the hazard switch. have to take trim panel off to replace it .Apply the parking brake.
If the vehicle is equipped with a column shift, position the transaxle shift control indicator to 1.
Adjust the steering wheel for access.
Using a small, flat-bladed tool, gently remove the bezel from the ignition lock cylinder.
For the Impala, remove the right and the left access covers from the instrument panel (IP) fuse block.
For the Monte Carlo, remove the left access cover from the IP fuse block.
Remove the steering column filler. Refer to Steering Column Opening Filler Replacement .
For the Monte Carlo, open the instrument panel compartment door.
Remove the trim plate screws from the IP cluster.
Start at the left side of the IP cluster trim plate. Grasp the trim plate and carefully pull rearward. Disengage the IP cluster trim plate in order to easily access the hazard warning switch
Disconnect the electrical connectors from the hazard warning switch.
Remove the hazard warning switch from the IP cluster trim plate.


13710300-sqgggmolzf4u4c55ip0gdkvq-5-0.jpg It's probably the switch on the steering column ! An not the flasher but you never know without testing .
Turn Signal Lamps and/or Indicators Inoperative
Step
Action
Yes
No
Schematic Reference: Exterior Lights Schematics
1
Did you perform the Lighting System Diagnostic System Check?
Go to Step 2
Go to Diagnostic System Check - Lighting Systems
2
Turn the ignition to the ON position.
Place the turn signal switch to a turn left or a turn right position.
Do the turn signal tamps flash ON and OFF?
Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
Go to Step 3
3
Disconnect the hazard switch.
Connect a test lamp between the TURN SIGNAL Fuse battery positive voltage circuit and ground.
Does the test lamp illuminate?
Go to Step 4
Go to Step 7
4
Reconnect the hazard switch.
At C201, connect a test lamp between the turn signal flasher supply circuit and ground.
Does the test lamp flash ON and OFF?
Go to Step 5
Go to Step 6
5
At C201, connect a test lamp between the turn signal flasher supply circuit of the hazard switch and inoperative turn signal lamps supply voltage circuit.
Does the test lamp flash ON and OFF?
Go to Step 9
Go to Step 8
6
Test for a high resistance or an open in the turn signal flasher supply circuit. Refer to Wiring Repairs and to Connector Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 11
Go to Step 10
7
Repair a high resistance or an open in the TURN SIGNAL Fuse battery positive voltage circuit. Refer to Wiring Repairs and to Connector Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 11
--
8
Repair a high resistance or an open in the turn signal lamps supply voltage circuit. Refer to Wiring Repairs and to Connector Repairs in Wiring Systems.
Did you complete the repair?
Go to Step 11
--
9
Replace the turn signal switch. Refer to Multifunction Turn Signal Lever Replacement - On Vehicle in Steering Wheel and Column.
Did you complete the replacement?
Go to Step 11
--
10
Replace the hazard switch. Refer to Hazard Warning Switch Replacement in Steering Wheel and Column.
Did you complete the replacement?
Go to Step 11
--
11
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Jul 21, 2012 | 2002 Chevrolet Monte Carlo

1 Answer

My turn signals stopped working and my hazard light don't work either. I had problems for a while now they just stopped working? help


its your flasher. for either switch you must disassemble the steering column. The signal flasher switch is the first switch you will encounter. The hazard switch is a little farther down the column.Iif your looking to replace the flasher unit . There are 2,one for the signals & one for the hazards. Look under the dash,near the fuse block,they are normally small round cylindrical units that plug in with either 2 or 3 spade terminals. The signal flasher is usually plugged into the fuse block, the hazard flasher is usually near by with just wires plugged into it.be aware that if your going into the steering column you will need special tools

May 21, 2011 | 2000 Chevrolet Malibu

2 Answers

89 jeep cherokee blinkers and hazards not working


For 1989 Jeep Cherokee the Flasher is located:
* Front seating area, driver side, under dash, above kick panel, mounted in bottom of convenience panel for Hazard flasher
* Front seating area, driver side, under dash, above kick panel, mounted in top of convenience panel for Turn signal

Hope helps.

Apr 27, 2011 | 1989 Jeep Cherokee

1 Answer

I have Ford Explorer model 1998 but its indicator lights are not working meanwhile the hazzard lights are working


Your turn signal flasher is separate from the hazard flasher. Replace the turn flasher.

Both the turn signal flasher and the hazard warning flasher are mounted on the fuse panel on the truck. To gain access to the fuse panel, remove the cover from the lower edge of the instrument panel below the steering column. First remove the two fasteners from the lower edge of the cover. Then pull the cover downward until the spring clips disengage from the instrument panel.
The turn signal flasher unit is mounted on the front of the fuse panel, and the hazard warning flasher is mounted on the rear of the fuse panel.

Oct 02, 2010 | 1998 Ford Explorer

2 Answers

No signal lights at all and no emergency flashers


you need to check the "combination turn signal/hazard flasher/daytime running lights module"
it is located in the junction block,the junction block is adjacent to and left of the steering column,you need to remove the lower dash panel below the steering column,then remove the steel knee brace.

Dec 31, 2009 | 1996 Plymouth Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,561 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...