Question about 1991 Toyota Supra

2 Answers

I have replaced the Clutch Slave for a 1990 Supra Turbo, and after the next day all the Fluid leaks out from the resevior.I don know wher the fluid goes. what should I do next? Thank You, Frank

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Clutch master and slave cylinders should always be replaced together as should wheel cylinders and calipers(replaced in pairs). The clutch hydraulics are used 3 to 5 times more than the brakes (depends on how many speed trans you have) and wear evenly.

Posted on Aug 25, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 51 Answers

Hey Frank.When one cylinder goes the other usually follows because higher pressure needed to operate a new cylinder, sometimes the fluid leaks down the firewall or down your clutch pedal onto the floor, if its your master cylinder that is.You can get a new one or get your old one rehoned and a stainless steel tube inserted and it will last forever as theyre made of aluminium and wear. Either way you'l need to buy a new kit for the inside of it.Be mindful what you order as some models of cars the abs and non abs cylinders are a very slight different diameter. I hope this helps.

Posted on Jan 12, 2009

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

mas66
  • 104 Answers

SOURCE: Clutch fluid resevoir

Clutch fluid and brake fluid are the same thing. It's usually only sold with the label "Brake Fluid", but it is used in the clutch system as well. In fact, a lot of vehicles only have the one reservoir for both brake and clutch systems. You should use DOT 4 or higher grade. Cheers.

Posted on Oct 25, 2008

  • 8 Answers

SOURCE: toyota supra turbo 1990, manual (7mgte engine) Clutch problem

You ever think about replacing your rubber clutch line with a hard line or just replacing the rubber line

Posted on Aug 18, 2009

  • 57 Answers

SOURCE: Replaced whole clutch and slave

Sounds like you need to bleed the system again, or you have an air leak. try bleeding again and just check your fittings for tightness.

Posted on Jan 20, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 Honda EX clutch. It does not ingage. It pops to the top or sticks to the floor


Not sure of the model EX, but it probably has a clutch hydraulic slave and master cylinder that has leaked out the hydraulic fluid. Fill the clutch master cylinder (near the brake master cylinder) with brake fluid and pump the clutch pedal several times. The clutch work again until the fluid leaks out, so the permanent fix is to replace the master and or slave cylinders and bleed the system. Other models have a clutch cable that would need replacing in this case

Oct 24, 2017 | Honda Cars & Trucks

1 Answer

Symptoms low clutch fluid


The clutch fluid is also your brake fluid. If it is low then you have a leak somewhere, could be your slave cylinder, or even brake pads are low

Feb 09, 2014 | 2001 Volkswagen Jetta TDI

1 Answer

How to blead clutch in 2004 holden clubsport


im assuming its a vy clubsport?
Make sure you remove all the old fluid from clutch resevior and clean it out properly.
You will need to raise the vehicle on a hoist or atleast 4 cat stands .
you will need 3 people in total to get the job done correctly.
fill the clutch resevior with new fluid.
get someone to stay under the car to open slave cylinder to release air.
someone to seat to drivers seat to pump clutch pedal.
and someone at resevior all the time to top up fluid.
when bleeding system just pump the pledal slowly when the person bleeding slave cylinder says hold.hold the pedal down with light pressure when the slave is open you will get air and then little fluid .
repeat process until just good flow of fluid comes out ,once this happens you should have a good pedal..
hope this helps you

May 29, 2012 | Holden Commodore Cars & Trucks

1 Answer

No fluid comes out the clutch slave cylinder bleeder


make sure that the resevior is full then have someone push down on the clutch pedal a few times and hold it down on the last stroke while you open the slave cylinder valve. then repeat as necessary until fluid comes out. Dont't let the resevior run out of fluid.

May 26, 2012 | 1994 Toyota Pickup

2 Answers

What could cause a clutch pedal in a 1996 honda accord to lost pressure


no fluid in the clutch reservoir due to a failed clutch slave cylinder
time to replace both the clutch slave and master cylinder

Dec 02, 2017 | 1996 Honda Accord

1 Answer

1997 sonoma - clutch bleeding


I just did mine 2 days ago. There is a allen wrench spot on the back of the slave unit in the front of ******. You need one person with a good leg to get in truck and start pumping clutch one person under truck with allen wrench to loosen and tighten screw. Guy inside needs to pump maybe like thirty times up and down before it pays to open bleeder on slave unit.The guy inside needs to hold down clutch while the guy opens watches then closes bleeder. then guy from inside needs to go under hood to make sure the resevour still has enough fluid.It takes brake fluid in resevour. You don't want the resevour to run low on fluid or you will have to start all over. I had a small leak in the line leading to slave cylinder were I lost fluid and that's how I got air in system make sure you don't have any leaks. Good luck I know it works I have more clutch know then a year ago when I had the slave unit changed.

Apr 11, 2012 | 1997 GMC Sonoma

3 Answers

Clutch pedal sinks to floor and won't take gears. when it does take gear it will shift fine after a few minutes but now won't take gears at all


possible bad slave cylinder on transmission, you do have a hydraulic clutch, have you checked the fluid in it? it might be your problem. hope i helped!!

Aug 16, 2010 | 1998 Honda Prelude

1 Answer

1987 supra turbo master cylinder troubleshooting


Jack up the car with adequet support have someone work the clutch in and out,obseve the slave cylinder when the clutch pedal is realeased--is it free or hanging up -still tight then problem with the master or slave.If not then the clutch plate may be stickly on the splines when cold,

Nov 09, 2009 | 1990 Toyota Supra

Not finding what you are looking for?
1991 Toyota Supra Logo

413 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

81424 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...