Question about Daewoo Leganza

1 Answer

Hi ive got a daewoo espero the cam belt has come off ive got a new one to put on but need the too time marking s to put the cam belt in right please can you help the model i have a put down isnt my car its the espero

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Daewoo Master
  • 60,691 Answers

Required tools: 13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm allen head sockets 19mm socket prybar needle nose pliers If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pullys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS. Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pully ( the 4 allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pully) on the camshaft pullys -- ( intake cam line up the line on the pully with the line on the inner cover)( exhaust cam line up the arrow on the pully with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would reccomend you replace the water pump, both plastic idler pullys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhause Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pully, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal. To clarify, on the DOHC engine, the intake cam gear has a line on it, and the exhaust cam gear has an arrow on it. These should be lined up with the corresponsing line and arrow on the VALVE COVER, pointing straight up. I just went through this process over the weekend, and spent quite a bit of time looking for these marking as I had removed the valve cover. Once I found them, it was plain and simple. In addition, be sure to not over tighten the belt when reinstalling. The tensioner has markings on it for "old" and "new". DO NOT adjust past "new", as the car will sound like a jet engine, and the belt will not last for very long. One more item that you may as well replace while you are in there is the cam position sensor if you have not already, as there have been issues with them, and the timing housing has to be opened to get to it

Posted on Nov 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cam shaft timming marks 1999 Daewoo 1.6 liter


there is a special tool to hold gears in correct place on some of these models, but you can hold one cam at a time with a spanner then feed belt on exhaust cam then inlet cam gear
get someone to hold gears in place while you feed belt on.
the inlet cam is more prone to turn off mark more than exhaust.
if you have tensioner that needs retaining pin in when installing
you fit belt while aligning timming marks
fit tensioner as last spot to feed belt on with retaining pin in adjuster
get correct tension on belt by turning water pump so that you can flex (turn) belt 90 degrees only just while using finger and thumb
tighten water pump check flex
check all timing marks are correct
remove retaining pin from auto tensioner
turn motor over a couple of turns by hand observing tensioner arrow should hover around V mark and that all timing marks align up again(after one complete turn)

Aug 02, 2009 | 1999 Daewoo Lanos

1 Answer

Can you show me the alignment of the Timing Belt timing Mark of Daewoo1996 Espero Due to not exact the Idling the Engine That i overhauling,there no Timing mark in the plate or back of the sprocket,Can you...


on twin cam engines cam marks face each other at 3 o clock and 9 o clock and crank gear mark goes at 6 o clock in line with mark in edge of sump/block

Jul 07, 2009 | Daewoo Lanos Cars & Trucks

1 Answer

Daewoo nubira injectors arent firing ...the timing belt broke which bent the valves ive had the head fixed and put back to gether and it still wont start....afte some tests we found the injectors are...


if timming marks were set correctly and it is single cam engine were lifters bleed out before assembly? it may not have any compression
may have to remove top rocker cover only and use lever to push down on rockers to there is clearance between cam

Jun 10, 2009 | 1999 Daewoo Nubira

2 Answers

Looking for cambelt timing marks/ positions please, Twin cam engine Thanks Kevin


these bend valves if belt breaks while running
Align the timing marks on the camshaft gears to the notches on the camshaft cover, using the intake gear mark for the intake gear and the exhaust gear mark for the exhaust gear.
Align the mark on the crankshaft gear with the
notch at the bottom of the rear timing belt cover.

May 12, 2009 | 1999 Daewoo Nubira

2 Answers

I need a diagram for the timming belt for a daewoo nubira 2000


what model ?? 8 valve?? 16 valve?? petrol ?? diesel?? .Remove np one spàrk plug and put a long thin screwdriver into hole and turn engine till the piston is at the top and then look for timing marks ,if you still cant see them paint the cam gear .with a couple of spots of white paint ,the lower crank mark it when the keyway points at the top of bottom of the engine.If i remember rightly these opel engines have the timing mark as a white line on the belt .But mark it anyway and always rotate the engine 360% by hand to make sure the valves clear and you have it right

Mar 20, 2009 | 2000 Daewoo Nubira

1 Answer

2001 Daewoo Laganza Timing Marks


Hi...
On your request,
For the Crankshaft timing MARK.
You need to remove the cover, the Timing mark is inside.
Your Information is right.
The cam's at 12 O clock. Remember the left side Intake and the right side Exhaust.
Because each of the Cam sproket have the sign , Intake and exhaust

Ok. I hope this help on your question.
I have Pictures of all the marks. But to send you pictures I need any E-MAIL adress.
Because this site don't let me send more than 150kb. and the pictures are around 250kb.

Thank you for use fixya...


Oct 26, 2008 | 2001 Daewoo Leganza

1 Answer

Daewoo espero


Call the dealer and tell him your engine size, V6, 4cyl etc. ask if the engine is free wheeling when the cam belt breaks, most are these days except Mitsubishi's 4 cylinders.

Jul 30, 2008 | 2002 Daewoo Lanos

2 Answers

Timeing belt


IF YOUR TIMING BELT BROKE OFF BEFORE YOU CHANGED THE TIMING BELT DO YOU HAVE TO TAKE THE COVER OFF OF THE HEAD VALVE LOOK AT THE CAMS AND YOU WILL SEE THAT THE VALVES ARE BENT IF THE CAM IS NOT TOUCHING THE VALVES ARE BENT BEFORE YOU ALINE THE CAM GEARS YOU HAVE TO PUT THE CRANK SHAFT GEAR IT HAS A MARK AT THE BOTTOM OF THE OIL PEN MAKE SURE THAT WHEN YOU GET IT ALL SET UP RETURN THE GEAR TO THE MARK ON PULLY ALSO THE TIMING MARKS ON THE CAMS HAS TO MARKS ON THE COVER THE LEFT CAM GOES AT 12:00 THE RIGHT CAM MAKE SURE THE EXHAUST LINE LINES UP AT 12:00 OTHERWISE IT WONT START BECAUSE YOU DONT HAVE NO COMPRESSION I HOPE THIS IS HELPFUL FOR ANYBODY THAT NEEDS TO REPAIR THE ENGINE



ALCANTARAMONICO@YAHOO.COM

May 16, 2008 | 2000 Daewoo Leganza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

494 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daewoo Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

yadayada
yadayada

Level 3 Expert

60667 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Are you a Daewoo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...