Question about 1989 Oldsmobile Cutlass Supreme

1 Answer

Need to change ignition but have no key 1995 olds cutlas serria

How do i change ignition without a key and how do i access the steering colum to change it

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 99 Answers

Diconnect battery and wait 30 minutes, then remove steering whell and then remove clip holding lock plate, remove plate and unscrew, usually three screws and remove the turn signal sir coil assembly, then you will see a bolt that is holding the lock cylinder in, it will have 2 wires attached to it and they must be disconnected at the base of the steering column and routed up through the column, then replace parts in reverse order, do not spin the sir coil or you will have to replaqce it

Posted on Nov 30, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need to know where to plug the wires for the ignition key cylinder


look under the drivers foot well it is just a plug on fitting on the electrical part of the ignition switch .you cant plug a wire in .if you want to fit something you do that at a spare fuse section ,of the fuse box.

Dec 20, 2013 | 1995 Chevrolet Caprice Classic

1 Answer

I have a 1999 Jeep Grand Cherokee. The vehicle


sounds like the key is either worn down to where the ridges in the key wont push the tumblers inside the key lock cylinder into their proper place to move the cylinder into the starting position. Or your steering colum is locked and the wheel is moving freely as if it were not. So your solution would be to either have an expert look at it (estimated cost: 200$ low/400$high) or you can attempt to fix it yourself.
should you choose the "I'll fix it myself" method....try getting a new key made at a hardware store since keys wearout over time (ie:10years of turning that old key), this may solve the problem right away if the ridges are just worn on the key. Or the hard way, you need to get a phillips screwdriver and some jewelers tools and an 8mm or 10mm wrench/rachet+socket to disconnect the battery, then underneath the steering colum just under the ignition is a hole in the colum shroud/cover, from there you can disconnect the ignition key lock cylinder (the thing you put your key into). once you've removed the cylinder from the steering colum you should test your key again to see if you can turn the cylinder outside of the colum if you cannot then buy a new ignition key lock cylinder for about 15$-30$...problems solved.

Nov 18, 2009 | 1999 Jeep Grand Cherokee

2 Answers

I need to change the key switch on the steering colum and can,t get the old one out


You must remove the steering wheel and remove the signal switch to get access to the ignition lock retainer. This retainer can be a small bolt or a reccessed pin that has to be pushed to remove the lock. The key may have to be in place to help removal. If this is the case then the key should be in the" on" position.
PS The push pin may also be located at the base of the lock cylinder on the outside of the housing. Look around under the housing before getting into the steering wheel.

May 26, 2009 | 1989 Ford Bronco

1 Answer

Want to remove the ignition lock cylinder since a broken key is stuck inside.


get a phillipshead un do about 4 screws from underneath plastic cover which hides steering colume. remove cover you will see white plug on the left hand side of ignition barrel disconect.then right hand side there will be acable disconect.now get a small chissel and anti clockwise tap bolts which have no heads on them that are on top of steering colume when they are alittle bit lose use plyers its easier pull bolts out clamp will then come of and then you can pull whole ignition of. now there is 2 brass pins which hold barrel in ignition up near the key end remove and barrel will come out but it might be easier to take whole ignition to locksmith and get them to do it and get new key for around 30 bucks i did a mates about couple months ago seeya orangepeel.

May 18, 2009 | 1995 Mazda 626

1 Answer

Removing steering colum


if you are refering to the ignition switch, put the key in the ignition and turn it to "on".  Do not start the car.  there should be a hole on the bottom of the column below the ignition switch.  Stick a long skinny object, such as an unbent paper clip into that hole.  There is a littlle "button" that you have to depress and pull the switch out.

Feb 27, 2009 | 1995 Ford Taurus

1 Answer

Car key


You should be able to give you vin number to the dealer. they can cut you a new key. As for removing the lock... you need to turn the ignition to the on position then push an 1/8" rod into the small hole in the bottom of the steering colum right under the lock assembly. After placing it in the ingition lock will easly pull out. Insert the new one in reverse order.

Nov 07, 2008 | 1995 Ford Aerostar

2 Answers

Put the starter in and hooked up the battery and no power to the starter it dont even turn over and the battery is fully charged


sounds like sthe ignition switch. when you turn the key to run do yhe dash lights come on? there is a rod that connects to the key switch and runs down the top of the steering colume. at the top of your colume just before the brake pedal. you should see it. that is actually the switch . to access easier take lower panel off and remove the two bolts that secure the colume. the colume will come down some to give better access. you will need it. there is a couple of small screws that hold it. also check the plug for overheating,this is common. good luck

Aug 02, 2008 | 1995 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

211 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...