Question about 2005 Mercedes-Benz Mercedes Benz E320 Cdi

Open Question

Torque strut bushing 2003 e320

I have a sluggish slow down and take off

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is the torque on stut bolt


strut bolt? the two bolts attaching the knuckle to the strut.
If no one knows, I would advise about 100ft-lbs.

Apr 30, 2015 | 2004 Ford Escape

2 Answers

How to comprese strut on a2000 Buick lesaber


you can take the strut cartridge from the top,without disassembling spring and knuckle,there are there are 3 15 mm bolt on strut 9need to be torqued to 24 LB FEET) then you need special tool to take the strut mount and cover out ,(it is 24 mm bolt that you have to put #50 torx bit in the center to keep strut rod from tuning NEED 59 LB FEET of torque)

,then you take the bumper,mount and the boot out to put the special tool to keep the strut cartridge in place or it will shift side way ,and you have to tow the car to shop to get it done!!!,after that you use special tool to loosen the cartridge cover (NEED 82 LB FEET WHEN PUT BACK)take the strut out,suck the oil with the hand pump out,and put 50CC back,as it needed to help cool down the strut,( when you put new strut in the oil level should cover half of the strut no more) ,and reverse the process after that,

this is the tool you need,
Alltrade 648609 Kit 19 General Motors Body Strut Remover Tool Set

Oct 24, 2014 | 2000 Buick LeSabre

1 Answer

Notice slight shimmy between 30 and 45... Severl tires slightly low. Put air in tires and now shimmy is worse. Again at speeds of 30 to 45 while acceleration or slowing down.


Hi,
Could be tires need balanced. If they were run low on air, they could be worn and need replaced.

Also, front end suspension may need replaced: Struts/shocks, tie rods, ball joints, bushings. A shop can ID these parts to fix.

GL,
Td

Oct 10, 2012 | 2003 Chrysler 300M

1 Answer

Noise in back shock absorbers after replce them, I want to know if there are some bushings located?


DID YOU TORQUE STRUT CARRIER BOLTS TO 60 FT LBS AND TORQUE UPPER MOUNTING NUTS TO 22 FT LBS. IF YOU DIDNT TIGHTEN ALL BOLTS AND NUTS YOU WILL HEAR REAR STRUT NOISE.

Sep 02, 2010 | 2003 Hyundai Tiburon

1 Answer

Broken top bushing on front suspension strut. The wheel drops down when the car is put on a lift for servicei Is this bushing replaceable without replacing the whole strut assembly?


I belive you talking about strut tower bushing.
Yes you can replace it without repl. strut , but you have to take strut apart. Very common on Toyota's.
You need a strut compressor for this job.

May 22, 2010 | 1988 Toyota Camry

1 Answer

TL Magna replace strut top bushes how to drop


try not to kill yourself.
You need a spring compressor for this job.
Three nuts on top , two at nuckle , disconnect any brake hoses or wires attached to strut if present ,
If brake hose goes through the bracket on the strut , and there is no options but disconnect brake line , I usually cut bracket carefully the way I can split bracket and take hose out without disconnecting the brake line.But make sure that it cut really nice so you can put it back together with locking spring.
After that , take strut assy. out and COMPRESS THE SPRING (spring compressor) ,after-take center nut on top of the strut out and you done. Memorize the way (mark it) spring was sitting , and sequence
for the parts and put it back together .
Installation - opposit of removal.

May 05, 2010 | 2003 Mitsubishi Lancer

1 Answer

Front end shakes and wobbles


Struts and upper strut bushings.

Apr 02, 2010 | 1996 Jeep Grand Cherokee

2 Answers

2002 clunking problm


Check the macpherson struts to ensure they are not loose.  One way to check is visually in the engine compartment.  Check the top of the struts to ensure the nuts are not loose.  Another is to raise the side of the van where you hear the clunk.  Raise it so the wheel is off the ground.  Grasp and shake the strut to see if it is loose.  The struts should not be loose, but you never know.  As the strut is certainly ivnolved in bumps and rotates when the wheel turns, I would check there since you have already explored the bushings and links.

Jan 10, 2009 | 2003 Dodge Caravan

2 Answers

Intermittent clunking in front end


pt cruiser are famous for lower control arm bushings they go bad take a tire iron and pry on the lower A-arm by thbushing and see if you have play

Aug 15, 2008 | 2003 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

yadayada
yadayada

Level 3 Expert

60541 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

164 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...