Question about 2001 Ford F250 Super Duty Super Cab

1 Answer

Starter Bolt What is starter bolt size for 99 F250 Ford Diesel truck

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 71 Answers

Obviously you do not have the one missing; therefore I would do one of two things... Take out one of the others, if there three, then no problem the other will hold till you get the other two back in. If the one you lost is broken off in the bell housing, then you must take off the starter and drill out the broken bolt and you can get a replacement from the Ford dealer, Pep Boys or a junk yard.


Good luck

Posted on Jan 02, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove install starter


2 tips. Use a rope around the starter and suspend it to aid in lining it up for install. Tape the inner most bolt to the socket to prevent the bolt from falling or use magnetic socket inserts.

May 12, 2013 | 2003 Ford F250 Super Duty Crew Cab

2 Answers

My 1988 ford f250 460cid auto with headers wont start when hot


the headers are heating up the starter best bet is to install a heat deflector between the starter and the headers, common problem

Oct 22, 2010 | 1989 Ford F 250

1 Answer

1988 Chevy Tahoe Starter going out. Need to replace


Generally starters have 2 or 3 bolts and a thick wire coming from the battery and other miscellaneous connections.

You did not specify a vehicle that was on my list, i.e. 1988 Chevy Tahoe.

However, it may be similar to a Suburban R10:
REMOVAL & INSTALLATION The following is a general procedure for all trucks covered in this manual, and may vary slightly depending on model and series.
  1. Disconnect the negative battery cable at the battery.
  2. Raise and support the vehicle.
  3. Disconnect and tag all wires at the solenoid terminal. NOTE: Reinstall all nuts as soon as they are removed, since the thread sizes are different.
  4. Remove the front bracket from the starter and the mounting bolts. On engines with a solenoid heat shield, remove the front bracket upper bolt and detach the bracket from the starter. Fig. 1: Starter mounting location — 4.8L engines 84903021.gif
    Fig. 2: Starter mounting location — 4.3L and 5.0L engines 84903022.gif
    Fig. 3: Starter mounts — 5.7L and 7.4L engines 84903023.gif

  5. Remove the front bracket bolt or nut. Lower the starter, front end first, then remove the unit from the truck. To install:
  6. Position the starter and tighten all bolts as follows: R/V Series:
    • Thru-bolts: 40 ft. lbs. (54 Nm)
    • Bracket bolt: 30 ft. lbs. (41 Nm)
    • Nut (gas): 11 ft. lbs. (15 Nm)
    • Nut (diesel): 90 inch lbs. (10 Nm)
    C/K Series:
    • Thru-bolts: 35 ft. lbs. (45 Nm)
    • Bracket bolt (diesel): 24 ft. lbs. (33 Nm)
    • Nut (diesel): 75 inch lbs. (8.5 Nm)
  7. Reconnect all wires. Fig. 4: Disconnect the negative battery cable 87982p25.jpg
    Fig. 5: Remove the starter retaining bolts 87982p30.jpg
    Fig. 6: Remove the starter from the vehicle 87982p31.jpg
prev.gif next.gif

Jul 19, 2010 | 1984 Chevrolet Chevy

2 Answers

How do you replace the starter on a 1989 SW1500?


The following is a general procedure for all trucks covered in this manual, and may vary slightly depending on model and series.
  1. Disconnect the negative battery cable at the battery.
  2. Raise and support the vehicle.
  3. Disconnect and tag all wires at the solenoid terminal.
Reinstall all nuts as soon as they are removed, since the thread sizes are different.
  1. Remove the front bracket from the starter and the mounting bolts. On engines with a solenoid heat shield, remove the front bracket upper bolt and detach the bracket from the starter.

f6823f2.gif
Starter mounts-5.7L and 7.4L engines

  1. Remove the front bracket bolt or nut. Lower the starter, front end first, then remove the unit from the truck.
To install:
  1. Position the starter and tighten all bolts as follows:
R/V Series:
  • Thru-bolts: 40 ft. lbs. (54 Nm)
  • Bracket bolt: 30 ft. lbs. (41 Nm)
  • Nut (gas): 11 ft. lbs. (15 Nm)
  • Nut (diesel): 90 inch lbs. (10 Nm)
C/K Series:
  • Thru-bolts: 35 ft. lbs. (45 Nm)
  • Bracket bolt (diesel): 24 ft. lbs. (33 Nm)
  • Nut (diesel): 75 inch lbs. (8.5 Nm)
  1. Reconnect all wires.450af3b.gif

Disconnect the negative battery cable


56132e9.gif
Remove the starter retaining bolts


d54e957.gif
Remove the starter from the vehicle

Apr 26, 2010 | 1989 Chevrolet Suburban

1 Answer

How many bolts on a 1992 ford diesel 7.3 starter and how do you remove them


there are 3 bolts holding your starter on. i suggest a socket, long extension and a ratchet for the top hard to reach bolt. wrench works fine on the other 2 bolts

Feb 07, 2010 | 1992 Ford F350

3 Answers

NEED TO REPLACE THE GROUND WIRE TO THE STARTER ON A 99 FORD F250 LIGHT DUTY WITH 5.4 V8 AND NEED A WIRE DIAGRAM


why do you need a diagram?, if you have a new one, just route and install it just like the old one.

Oct 14, 2009 | 1996 Ford F250 Crew Cab

2 Answers

How to get top bolt off of 1988 F250, 7.1 L diesel starter


You need a long extension and swivels for a rachet to get to the one bolt thats on top next to the block. Check for a way to get to it from the front.

Jun 25, 2009 | 1988 Ford F 250

1 Answer

Starter


There is a bolt on the back side of the starter and two in the front. make sure you get the one in the back.I hope this helps.

Jan 19, 2009 | 2003 Ford F250 Super Duty Crew Cab

Not finding what you are looking for?
2001 Ford F250 Super Duty Super Cab Logo

238 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

68970 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Ron Lankford

Level 3 Expert

5383 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...