Question about 2000 Ford Crown Victoria

2 Answers

2000 Ford Crown Victoria

I recently ran out of gas in my 2000 Ford Crown Crown Victoria.After putting gas, it starts but doesnt stay running??? Did I burn out a fuel injector, or maybe the fuel pump??

Posted by on

  • 5 more comments 
  • Anonymous Mar 14, 2014

    ran out of gas. fuel getting to fuel injectors but not enough to stay at idol and bogs when push gas pedal

  • Anonymous Mar 17, 2014

    wont start has power and no clicking sound

  • Anonymous Mar 18, 2014

    i have a problem with the 1992 ford crown victoria idleing when cold

  • Anonymous Mar 22, 2014

    car is saking before running

  • Anonymous Mar 22, 2014

    car saking

  • Anonymous Mar 26, 2014

    timing chain marks

  • Anonymous Mar 26, 2014

    Where is it located



2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Won`t run unless you hold the accelerator down

Posted on Dec 13, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert that hasĀ over 500 points.


    An expert who has answered 200 questions.

  • Expert
  • 261 Answers

When you hold the accelerator does the vehicle stay running? if so the problem is in ithe IAC idle air control motor, take a small screw driver and using the handle tap the iac motor and usualy the motor will kick in and the vehicle will run fine then if the problem is rectified replace the IAC

Posted on Nov 24, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2000 ford crown victoria not getting gas pressure

If you are not getting any gas pressure, then you need to replace the fuel pump.

Mar 04, 2014 | 1988 Ford Crown Victoria

2 Answers

Car ran fine to the gas station, stopped to put in the gas. Restarted the car and she wouldn't accelerate above idle without dying completely. fuel pump is new, exhaust removed to test catalytic conve

Have you checked fuel pressure with a gauge ? Is it possible you got a tank of bad gas ? Have you tried running the car with the gas cap off to check for venting problems ?

Feb 17, 2014 | 1999 Ford Crown Victoria

1 Answer

It have a 1994 crown victoria it ran out of gas I put 5 gallons of gas in it, when I turned the motor over it started right up, it ran for about a minute and a half then quit. I changed the filter, checked...

Air in the fuel line. Take one small wire off the starter relay and turn and hold the key in the start position for a while. Listen for the fuel pump. It will run fast for a second then slow down. When it does, put the wire back on the starter relay and crank the engine.

Aug 29, 2017 | 1994 Ford Crown Victoria

3 Answers

2000 Crown Vic cranks but won't start.

Check the fuel pump reset switch again, if it is popped back out then replace that little switch in the trunk, any ford one will do. it works off a magnet and a bearing to close the circuit for the fuel pump. easy fix.

Oct 05, 2009 | 2000 Ford Crown Victoria

1 Answer

1985 crown victoria stalls out

Why not hook a fuel pressure gauge up to it & see what the pressure is ?? Am I missing something here?

Aug 31, 2009 | 1985 Ford Crown Victoria

1 Answer

Stalls when i push the gas

Your MAF SENSOR needs to be serviced or replaced. Make sure your air cleaner is clean and the ducting is secured

Jul 04, 2009 | 1983 Ford Crown Victoria

1 Answer

Wont stay running after starting

That sounds like your Idle Air Control valve has gone out.

You can get one at any parts store, and swap it out in a few minutes.

If that doesn't fix the problem, look at your Mass Air Flow meter, that could be out too.

Dec 07, 2008 | 1999 Ford Crown Victoria

1 Answer

1980 ford ltd crown victoria

your car broken, i sergest taken it to a garrage

Sep 19, 2008 | 1991 Ford LTD Crown Victoria

Not finding what you are looking for?
2000 Ford Crown Victoria Logo

Related Topics:

603 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77939 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5651 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides