Question about 2000 Ford Ranger SuperCab

1 Answer

What is the sensor on the back of the head 2000 ranger

I have a sensor on the back of the head but i don,t find a wire to plug into it --- do you what this sensor is? -- should there be a wire pluged into it? - if so would it be in the main wire harness?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert who has answered 1,000 questions.

  • Master
  • 1,198 Answers

The oil pressure sensor is on the driver side, rear.

Posted on Nov 24, 2008

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Knocking engine

Spark plug wires crosses or timing is too early or octane too low for the higher compression..

Mar 30, 2014 | 2000 Ford Ranger SuperCab

1 Answer

I have a 2000 Ranger with 4 litre v-6. Lately when I start it, it doesn't start the first time I crank it. It starts alright the next time. What would cause this situation?

Try a general tune up; new spark plugs ( properly gapped), new spark plug wires, new air filter, new oil and filter. The first thing I would do is run 2-3 bottles of injector cleaner though several takes of fuel and see if that clears the problem up. If the injector cleaner helps than it means you have alot of carbon buildup on your valves, piston heads, and spark plugs; if this is the case I would keep putting 1 bottle of injector cleaner in at every fillup for several months just to get rid of as much of the carbon as I could.

Apr 07, 2010 | 2000 Ford Ranger SuperCab

1 Answer

2000 Ford Ranger- engine stalling when slowing down to idol

replace th air idle bypass valve this is located on the throtle body and has 2 screws with 1 plug with 2 wires to it

Dec 29, 2009 | 2000 Ford Ranger SuperCab

1 Answer

2000 dodge neon no back up lights wiring and bulbs and fuses good

Range sensor? that would be a speedometer odometer sensor ! range traveled! you request if for reverse light switch yes? wiring and bulbs not the issue! the switch is located behind and down drivers side head light 1999 model is under battery box must remove to gain entry to switch round plug with flat top 2 wires entering hope this helps.

Dec 19, 2008 | 2000 Dodge Neon

2 Answers

Speed sensor diagram for 2000 ford ranger

This video shows the speed sensor and its location for a 2000 ford ranger xlt. It also describes the problems a bad sensor can give.

Nov 06, 2008 | 2000 Ford Ranger SuperCab

1 Answer

Head light switch

If you pull the trim off around the cluster the light switch will be easy to access, pull the lower trim off below the cluster trim there are screws there, once they are out the rest is easy.

Oct 27, 2008 | 2000 Ford Ranger SuperCab

1 Answer

Replacing spark plugs

grip the wires at the bottom near the spark plugs and turn left and right while gently pulling outward

Aug 15, 2008 | 2000 Ford Ranger SuperCab

Not finding what you are looking for?
2000 Ford Ranger SuperCab Logo

Related Topics:

49 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

69244 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22026 Answers

Ron Lankford

Level 3 Expert

5383 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides