Question about 1999 Acura TL

1 Answer

Brake Pad Replacement

I have not work on brakes for some time and paid for repairs. I have two Acura's and wanted to know if there are special tools required and if there is any documentation and where that would assist in the replacement.

The one site indicated
removal of the brake caliber was either two bolts and or allen bolts. And to tie up system to prevent any brake line damage.
Remove the entire pad assembly and install new parts
Use seat clamp to return piston
Re-install.

Please provide any direction that maybe helpful Regards

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 87 Answers

Hi,welcome to fix ya. heres the procedure there are no special tols needed just a 12mm socket and a pair of pliers will do click here If there is anything else I can help you with let me know .

Posted on Apr 05, 2009

6 Suggested Answers

468 Chevelle
  • 81 Answers

SOURCE: How Do I Remove & Replace Worn Inner Tie Rod Ends

Cut band clamp. use tie wrap. Special tool to remove inner tie rod. Autozone or others have them to rent. Must align after replacement

Posted on Mar 27, 2009

  • 6982 Answers

SOURCE: can not push the caliber piston back to install

hydro...you ever get brain lock...or is it hydrolock?
Mad guy...Disconnect the caliper from the brakeline. If caliper retracts you have an internally failed line (rubber hose). if it does not retract, caliper piston may be frozen, or the piston cocked in the bore while you were pushing it back in. If that's the case you can rebuild it, but the price on most reman calipers is low so you may consider replacing it.If the ont on the opposite side si balky, replace both.

Posted on Apr 02, 2009

  • 23 Answers

SOURCE: how do I get the rear brake piston to retract on a 2004 jetta?

take the caliper off the car put it in a vice and push very hard as you turn the piston it will go in eventualy

Posted on Apr 20, 2009

  • 574 Answers

SOURCE: 02 x type rear piston/caliber

make sure ur top is off the brake fluid reservoir and take a c-clamp and tighten it up this will force the piston in.

Posted on Sep 08, 2009

johnjohn2
  • 5763 Answers

SOURCE: How do I change the rear brakes on a 2005 Audi A6?

You must be very careful or this brake job will get very costly, depending on the brake system on this car, one you may have the caliper type that you need to use a tool that turns the caliper piston while it slowly compresses it, then you may have the style caliper with electronic praking brake actuator then you will need a scan tool to do the job, hopefully you did not damage the piston,hope this helps,if theres a small module box on the caliper then you will need scan tool. if it just the caliper with a emergency brake cable going to it then you need the tool that turns the piston by the notches on the face of piston.

Posted on Aug 14, 2010

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can i compress the caliper piston back of audi a6 2000 2.8l awd what kind of tools i need . Vise grip is not working.


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also.
But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!

For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!!

Check brake fluid level and top up if neccessary!!!

Oct 26, 2011 | 2000 Audi A6

1 Answer

I want to change my front brake pads How do I remove the old ones


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!!
For front brake pads. You should buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Apr 12, 2011 | Volkswagen Polo Cars & Trucks

2 Answers

2004 Jetta 1.8T - doing brakes and hear there is a concern about a sensor and wire for the ABS. Is there any concerns or is it just a pigtail connection to disconnect and then work on the...


The ABS wire is well away from your brake caliper. If your vehicle has brake pad warning wires, these may need to be replaced with the pads. They sometimes come with the pad set. Hope this helps...

Mar 04, 2011 | 2004 Volkswagen Jetta

1 Answer

I am changing my fron brakes on an Audi A3 1.8 1998 model and want to know the allen key size for the caliper?


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. First you must verify yours front brake disc diameter: 280 mm or 288 mm. (On my car y have 288 mm). After that you can buy the brake pads (with wear sensor). For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Feb 21, 2011 | Audi A3 Cars & Trucks

1 Answer

Anything special about changing front pads on audi a3? I've done honda, acura and toyota's.


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow: 1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose! 2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper. 3. Now you must thoroughly clean the brake calipers (free of grease). 4. Remove outer brake pad from brake carrier. 5. Pull inner brake pad out of brake caliper piston. 6. Check up the brake fluid level on the reservor, and emptying if neccessary! 7. Push piston back into brake caliper housing. 8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exist, must point in direction of brake disc rotation when vehicle is moving forward). 9. Install outer brake pad into brake carrier. 10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm. 11. Install both caps. 12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Aug 25, 2010 | 2007 Audi A3

1 Answer

Changed the front brakes and now I cant get the brake lines to hold pressure. Bleeder valves and caliper hoses are all tight. But now I have no brakes other than the e-brake. Help!


ACURA ANTI BRAKE SYSTEM.YOU NEED A ACURA SPECIAL TESTER O7HAJ - SGOO100Z.NEED SPECIAL WRENCH O7HAA-SGOO100 NEED TO RELIEVE PRESSURE IN THE ACCUMULATOR. THIS JOB FOR DEALERSHIP.YOU CANT MANUAL BLEED THIS BRAKE SYSTEM YOU NEED SPECIAL TOOLS TO BLEED.IF TRY TO BLEED WITHOUT RIGHT TOOLS YOU WILL DO MORE DAMAGE.

Jun 18, 2010 | 1992 Acura Vigor

1 Answer

WHAT TOOLS ARE NEEDE TO REPLACE AUDI A3 SPORTSBACK FRONT BRAKE PADS


For front brake pads replacement you need only usually wrench set, inclusive 7 mm allen key also. But for rear brake pads replacement you need obligatory a special caliper piston pressing tool, in order to press back rear caliper piston with parking brake automatic adjustment!!! For front brake pads. You must buy the brake pads with wear sensor. For change front brake pads you must raise vehicle, remove wheels, extract the retaining spring of the caliper, and remove the caliper as follow:
1. Do not disconnect the brake hose from the caliper, and do not allow the caliper to hang by the brake hose!
2. Remove top and bottom caps (on back side of the caliper) for access to guide pins, then unbolt and remove them from the brake carrier. Remove the caliper.
3. Now you must thoroughly clean the brake calipers (free of grease).
4. Remove outer brake pad from brake carrier.
5. Pull inner brake pad out of brake caliper piston.
6. Check up the brake fluid level on the reservor, and emptying if neccessary!
7. Push piston back into brake caliper housing.
8. Install inner brake pad (with expanding spring) in brake caliper piston. (Arrow marked on pad - if exists, must point in direction of brake disc rotation when vehicle is moving forward).
9. Install outer brake pad into brake carrier.
10. Bolt brake caliper housing to brake carrier using two guide pins. Tightening torque is 25 Nm.
11. Install both caps.
12. Insert retaining spring into brake caliper housing. Important: Depress the brake pedal firmly several times while the car is stationary so that the brake pads adjust to their normal operating positions!!! Check brake fluid level and top up if neccessary!!!

Feb 14, 2010 | 2006 Audi A3

1 Answer

Front brake pad replacement, any special tools?2001 ford taurus


no special tools just something to push the piston back like a pair of plumer grips or a srurdy screwdriver

Oct 28, 2009 | 2001 Ford Taurus

4 Answers

1996 olds aurora back brake pad replacement, how to compress the pads to get the caliper back over the pads?


Special tool is a 1" cube with tabs on each side that fits into indentations on the brake piston and can be purchased for $10-12 @ most discount parts stores. Use 3/8" ratchet with short extension and 'special tool to carefully turn piston onto internal hand brake screw. Take care to not tear dust boot. When piston is fully collapsed, make sure to align piston indentations perpendicular to brake pad as there are bumps on pad that fit into them. Also while screwing in piston either remove about 2/3 of brake fluid in master cylinder and refil afterwords or open the bleeder valve on brake piston assembly. Bleed if necessary.

Jul 18, 2009 | 1996 Oldsmobile Cutlass Supreme Coupe

1 Answer

2004 x3 rear brake pad replacement diy


You Can probably accomplish this yourself if you have a brake pad warning light or ABS/ASC light on you may need a BMW tech to reset the system to complete the job.

Jul 02, 2009 | 2004 BMW 3 Series

Not finding what you are looking for?
1999 Acura TL Logo

Related Topics:

251 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...