Question about 1991 Nissan Maxima

1 Answer

Water leaking out the bottom of my 91 maxima

Between the engine, transmisson , and bell housing

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 110 Answers

Core plug gone remove gearbox to replace

Posted on Nov 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Water leaking beside thermostat houseing


Replace the corroded housing and you will have to replace the rusted welsh plug in the rear of the engine . If it is from inside the bell housing it means gear box out and fly wheel / flex plate off

Jan 25, 2014 | 2002 Dodge Stratus

1 Answer

I have a 1987 2wd ford f150 and there seems to be rusty water from my rad leaking out of my transmission area???


Hi, there are freeze plugs on the back of the engine block. If one of them has rusted thru, it will leak coolant into the transmission bell housing and out the bottom. You will have to separate the transmission from the engine at least a few inches or more to repair the freeze plug. If you need instructions for doing this, please reply with your engine size and type of transmission.

Mar 15, 2011 | 1987 Ford F 150

1 Answer

1993 previa, engine water leaking from transmission bell housing at bottom. is there a freeze plug that is behind the bell housing??


yes there is a engine core plug and its behind and inside of the bell housing,, sorry its a gear box out job to fix it,,,or you could try
"block weld!" that may stop the leak for a short time,,,

Oct 18, 2010 | 1994 Toyota Previa

1 Answer

Where is my starter located on a toyota celica 1995


bottom of the engine at trans bell housing, you need to go under the car to get at it.

Oct 05, 2009 | 1993 Nissan Maxima

2 Answers

Ford 300 six water driping from bell housing


The freeze plug on the back of the engine block is leaking,the transmission and flywheel will need to be removed to get to it.

Jun 20, 2009 | 1981 Ford F 100

1 Answer

91 nissan maxima


See if you have a leak in any of your coolant tubes. If no leaks, you may have a bad thermostat that is stuck closed and needs to be replaced asap.

Jun 20, 2009 | 1991 Nissan Maxima

1 Answer

Location of speed sensor a for 99 dodge intrepid


The "Vehicle Speed Sensor" signal is generated by the transmisson output speed sensor. That is the one located at the rear of the case. It is externally mounted. That supplies "vehicle speed" info to the other On-Board Computers. The input turbine speed sensor is located just behind the bell housing area of the case. I believe the trans controller is the only module that needs that info. The Crank Position Sensor give engine RPM info and it is located on the bell housing near the engine block. I hope this helps.

Mar 29, 2009 | 1999 Dodge Intrepid

2 Answers

Water coming from bell housing.


If you are ABSOLUTLY POSITIVE this is where the Coolant is coming from the ONLY Sorce is Freeze plugs ,There are Usualy 2 Behind the Flywheel. Sorry For the BAD NEWS but this IS the only thing that can Leak Out of the Bell Housing, Transmissiou Must Come Out and Flywheel also, Once The Flywheel is OUT you will see the FREEZE PLUGS. Good Luck !! Please RATE ME !!!!!!!!!!!!

Mar 22, 2009 | 2007 Dodge Ram 2500 Mega Cab Laramie

Not finding what you are looking for?
1991 Nissan Maxima Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...