Question about 1991 Toyota Previa

1 Answer

Starter replacement - 1991 Toyota previa

Need location and removal and installation steps, picture of location would be very helpful. I understand it is under the driver seat with 3 bolts and wiring connections that are tough to reach.

Anything you can provide is appreciated, can't see paying for a manual I won't use

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 98 Answers

Here are detailed, step-by-step instructions for the removal and re-installation of your starter motor. Hope this helps! Have a great day!

Starter Toyota Previa 1991-1997 Repair InformationREMOVAL & INSTALLATION
See Figures 5 through 12

  1. Disconnect the negative battery cable from the battery.
  2. Raise and safely support the vehicle.
  3. If equipped with 4WD, remove the front driveshaft.
  4. Remove the nut and disconnect the starter wire.
Starter replacement - 1991 Toyota previa - 0900c15280089fbb.jpgFig. 5: Disengage the starter wiring
  1. Disconnect the starter connector.
0900c15280089fbc.jpgFig. 6: Remove the cap hiding the Starter replacement - 1991 Toyota previa - 0900c15280089fbd.jpgsrc="http://i.fixya.net/uploads/images/0900c15280089fbd.jpg" alt="0900c15280089fbd.jpg" class="h_mi" />Fig. 7: It will be necessary to use an extension to remove the nut
  1. Remove the bolt holding the starter stay to the upper stiffener plate.
  2. If equipped with 2WD, remove the starter by removing the nut and three bolts.
  3. If equipped with 4WD, remove the starter by removing tStarter replacement - 1991 Toyota previa - 0900c15280089fbe.jpgand the center bracket.
09Starter replacement - 1991 Toyota previa - 0900c15280089fbf.jpgclass=Fig. 8: Four bolts hold the starter in place 0900c15280089fbf.jpgFig. 9: The nut is located on the top of the starter 0900c15280089fc0.jpgFig. 10: Extract the starter from the engineTo install:
  1. If equipped with 4WD, install the starter, the center support bracket, nut, and theStarter replacement - 1991 Toyota previa - 0900c15280089fc1.jpg the bolts as follows:
    • Bolt A to 41 ft. lbs. (56 Nm)
    • Bolt B to 30 ft. lbs. (41 Nm)
0900c15280089fc1.jpgFig. 11: Bolt locations on the 2WD models
  1. If equipStarter replacement - 1991 Toyota previa - 0900c15280089fc2.jpgl the starter, nut and three bolts. Tighten the bolts as follows:
    • Bolt A to 41 ft. lbs. (56 Nm)
    • Bolt B to 30 ft. lbs. (41 Nm)
0900c15280089fc2.jpgFig. 12: Bolt locations on the 4WD models
  1. Install the bolt to hold the starter stay to the upper stiffener plate. Tighten the bolt to 43 inch lbs. (5 Nm).
  2. Install the starter connector.
  3. Connect the starter wire with the nut. Tighten the nut to 78 inch lbs. (9 Nm).
  4. If equipped with 4WD, install the front driveshaft.
  5. Connect the negative battery cable.
SOLENOID REPLACEMENT
The starter solenoid (magnetic switch) is an integral part of the starter assembly.
  1. Remove the starter from the van. Remove the heat insulator from the starter assembly, if equipped.
  2. Disconnect the wire lead from the magnetic switch terminal.
  3. Remove the two long, through bolts holding the field frame to the magnetic switch. Pull out the field frame with the armature from the magnetic switch.
  4. Toseparate the starter housing from the magnetic switch assembly, remove the two screws and the starter housing with the pinion gear (1.6 kW), idler and clutch assembly.
To install:
  1. If necessary, install the gears and clutch assembly to the starter housing. Apply grease to the gear and clutch assemblies and place the clutch assembly, idler gear, bearing and pinion gear (1.6 kW) in the starter housing.
  2. Insert the spring into the clutch shaft hole and place the starter housing onto the magnetic switch. Install the two screws.
  3. Install the field frame with the armature onto the magnetic switch assembly and install the two through bolts. Tighten the bolts on the 1.4 kW to 52 inch lbs. (6 Nm) and on the 1.6 kW to 82 inch lbs. (9 Nm).
There is a protrusion or tab on each part; make sure you line them up correctly during assembly.
  1. Connect the wire to the terminal on the magnetic switch and tighten the nut to 52 inch lbs. (6 Nm). Install the heat insulator, if equipped.
  2. Reinstall the starter on the vehicle. Check starter system for proper operation.

Posted on Nov 23, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1993 Previa was stalling on highway. Now it won"t start. No pressure at the fuel rail. Spark is good. Where do I start checking voltage for fuel pump? Is it likely fuel pump has intermittent fault?


Unless it is the fuse or relay to the fuel pump, you need a new one. They either work or they don't, have enough pressure or they don't. The old days of tapping the fuel pump with the haft of a hammer are gone. They also hide them in the fuel tank.

Search Results

fuel pump - 1993 Toyota Previa - RepairPal

https://repairpal.com > Questions > Toyota > Previa > 1993 Toyota Previa Sep 4, 2010 - where is fuel pump located? ' Find answers to your 1993 Toyota Previa question from certified mechanics and auto experts. how much does it cost to replace the transmission - 1991 Toyota ...
7 Jun 2014
Rough idle, bad hesitation on acceleration, perfect idle with TPS ...
24 Jan 2011
replacing fuel pump - 1991 Toyota Previa
8 Jul 2010
replace fuel pump - 1993 Toyota T100
20 Jun 2010
More results from repairpal.com

1991 Previa Fuel Leak.3gp - YouTube

? 2:45
https://www.youtube.com/watch?v=z9XTZozlclM
Mar 8, 2010 - Uploaded by tkeyla67
How to Replace a Fuel Pump : Removing Fuel Tank to Change Fuel Pump - Duration: 2:03. expertvillage ...

Toyota fuel pump install - YouTube

? 3:34
https://www.youtube.com/watch?v=5Hx1cLWncSI
Jun 19, 2015 - Uploaded by Supertuner
The all-trac gets a 255 fuel pump. ... This video does not have enough information to help someone in ...

Toyota Previa Questions - where is the relay fuel pump - CarGurus

https://www.cargurus.com > Questions > Toyota > Previa where is the relay fuel pump. Report; Follow. Asked by Zaida Dec 14, 2015 at 03:33 PM about the 1993 Toyota Previa. Question type: Maintenance & Repair ...

Apr 23, 2018 | Cars & Trucks

1 Answer

Where is the engine oil stick?


The Toyota Previa is a popular car that holds its value well. It is a rare "mid-engine" car which presents some unique problems when doing basic maintenance like checking the oil. Go here for step buy step instructions:


http://www.ehow.com/how_4540025_check-oil-toyota-previa.html#ixzz1H5JrQBL3

Mar 19, 2011 | 1991 Toyota Previa

1 Answer

TOYOTA PREVIA 1991 2400 CC THE SIGN OF OPEN DOOR


The door afar sensors are located in the door latches. Try spraying all the door latches with wd40 penetrating oil and see if that helps.

Jan 09, 2011 | 1991 Toyota Previa

1 Answer

1991 toyota previa will not start when it gets wet turns over okay.Where is the air cleaner that goes over carb?


may moisture getting in dist. cap, take off & dry out . i dont understand what you are saying about air cleaner>>>

Dec 12, 2010 | 1991 Toyota Previa

1 Answer

My starter is going and some times it starts today it won't. I read if I hit it it may start but I can't locate. The starter to hit it. Where is the starter located?


I had a similar problem, hitting it may work some times but I think the contacts in the solenoid are worn out, replace the contacts, I managed to buy them at the local Auto shop, but not easy to find, or replace the starter.
Removing and replacing the starter is not so easy.
Hope this helps.
Graham

Nov 01, 2010 | 1991 Toyota Previa

1 Answer

How to replace dash light bulb of 1991 Toyota Previa van


pop fuse cover, remove vent housing, remove speedo upper cover, remove 4 bolts holding speedo remove speedo, change bulb

Mar 31, 2010 | 1991 Toyota Previa

2 Answers

How do I remove and replace a starter from a 1993 Toyota Previa? I am told it's rather difficult and may include removing something from the automatic transmission.


Removal & Installation
  1. Disconnect the negative battery cable from the battery.
  2. Raise and safely support the vehicle.
  3. If equipped with 4WD, remove the front drive shaft.
  4. Remove the nut and disconnect the starter wire.
  5. Disconnect the starter connector.
  6. Remove the bolt holding the starter stay to the upper stiffener plate.
  7. If equipped with 2WD, remove the starter by removing the nut and three bolts.
  8. If equipped with 4WD, remove the starter by removing the nut, four bolts, and the center bracket.
To install:
  1. If equipped with 4WD, install the starter, the center support bracket, nut, and the four bolts.
  2. If equipped with 2WD, install the starter, nut and three bolts.
  3. Install the bolt to hold the starter stay to the upper stiffener plate. Tighten the bolt to 43 inch lbs. (5 Nm).
  4. Install the starter connector.
  5. Connect the starter wire with the nut. Tighten the nut to 78 inch lbs. (9 Nm).
  6. If equipped with 4WD, install the front drive shaft.
  7. Connect the negative battery cable.
Good luck and this should take about 2 1/5 hours from start to finish and if you like, use lock tight medium strength to make sure the bolts don't go lose on you.

Nov 04, 2009 | 1991 Toyota Previa

1 Answer

1991 Toyota Previa won't start


low voltage to starter. Check battery for proper charge (must be 12.5+ volts), clean and tighten battery terminals. If below 12.5 volts, charging or battery replacement is needed. Hopefully this helpd

Sep 03, 2009 | Toyota Previa Cars & Trucks

1 Answer

Toyota previa starter screw is strip thats on the starter you put ur hot wire on


you will need to remove the starter and you can buy a die for a smaller thread and re thread the stud to a different size.

Oct 18, 2008 | 1991 Toyota Previa

Not finding what you are looking for?
1991 Toyota Previa Logo

1,837 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...