Question about 1996 Saab 900

1 Answer

Replacement thermostat I am trying to replace the thermostat in my 96 saab 900s. Where can I find a diagram telling me where the thermostat goes.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 76 Answers

Here is an illustrated tutorial for the 2.0 liter turbo. It is essentially the same for the naturally aspirated 900S: http://bellsouthpwp.net/m/a/mattiaso/WebPages/Auto/therm.htm

Posted on Nov 25, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Diagram of Route for drive belt


http://www.neobrothers.co.uk/idler-pulley-grooved-alternative-saab-ng900-p-1674.html?osCsid=d79a4930a941d92e878a93633c1b9eed

Feb 15, 2014 | 1997 Saab 900

1 Answer

96 Saab 900s


39b786ac-476d-4302-8692-92bb3d45e652.jpg
Well the large hose goes to the throttle body and the small one is in the intake manifold. This was the only picture I could find for you. Hope it helps....

May 12, 2013 | Saab Cars & Trucks

1 Answer

Can some one tell me step b y step how to remove 1994 saab 900s radiator.


I agree with Dennis Weid. I would also like to add that it is very difficult to give you the instructions you are asking for since you did not take the time to mention YEAR, MAKE, MODEL, ENGINE SIZE, or TRANSMISSION TYPE of the vehicle you want instructions for.

As Dennis mentioned, www.alldatadiy.com is a very good place to get this information and usually also has diagrams for most operations that can be performed on most cars.

Apr 10, 2012 | Saab 900 Cars & Trucks

1 Answer

Where is the thermostat in a 900s oh. 97 saab 900S Well my car was overheating and I notice in this model car if you need your oil changed it will overheat. So there is oil and all my fluids are full...


Oil change interval has nothing to do with operating temperature. If your coolant is full, feel the upper radiator hose, when the vehicle is up to temp. if cool , thermostat is back from that hose,

Look for air bleeds, and read owners manual, some cars have coolant bleeds. Also, heater on high when filling coolant or risk bubbles...

My thought is that your fans may not be kicking in. They should cycle on and keep temp low enough. test them.

Sep 15, 2009 | 1997 Saab 900

1 Answer

Remove/replace shock absorber assembly 900s 1995 saab


  1. Slightly loosen hub center nut when all four wheels are on ground.
  2. Raise and support vehicle, then remove five wheel bolts and wheel.
  3. Remove hub center nut, then the wheel sensor,
  4. Press back brake piston using slip-joint pliers,
  5. Remove caliper from steering swivel member, then suspend in wheel housing with cable tie.
  6. Remove brake disc and back plate, then slightly loosen tie rod end nut.
  7. Press out tie rod end nut using puller tool or equivalent.
  8. Remove nut and tie rod end bolt, then the anti-roll bar to swinging arm nut.
  9. Remove outer ball joint nut.
  10. Press ball joint out of steering swivel member using puller tool or equivalent, installed on spring link.
  11. Remove nut and discard. This self-locking nut must not be reused.
  12. Remove three upper mounting nuts for MacPherson strut, then the strut.
  13. Clamp MacPherson strut in vice.
  14. Compress spring using spring compressor or equivalents.
  15. Hold piston rod and remove nut using MacPherson strut socket tool 89 96 662, or equivalent. This is a self-locking nut and must not be reused.
  16. Remove mounting and top spring seat, then the coil spring, gaiter and compression stop.
  17. Unscrew damper using wrench tool No. 89 96 670, or equivalent, then remove damper from strut.
  18. Reverse procedure to install, noting the following:
    1. Screw damper in place using wrench tool No. 89 96 670, or equivalent.
    2. Lower end of coil spring should abut against stop in bottom of spring cup.
    3. Position MacPherson strut on vehicle and install three retaining nuts on top mounting. Tighten nuts alternately, according to specifications.
    4. Always use new hub center nut with self-locking threads.

Jun 04, 2009 | 1995 Saab 900

1 Answer

Water temp gauge for 1997 saab 900s in not working.


Have you tried replacing the coolant temp sensor?

Apr 18, 2009 | 1997 Saab 900

2 Answers

Srs light stays on ,in saab 1990 900s


I did not buy the car,the link you have sent me on your first email does not work

Jan 27, 2009 | 1995 Saab 900

1 Answer

Rear muffler


The '96 900 S denotes the 2.3 liter non-turbo 4 cylinder engine. This car uses Saab part no. 5174990. The aftermarket version is sold for $184.00 and the OEM for $270.00 at SaabSite. The aftermarket Starla/Walker rear muffler is sold at eeuroparts for $159.90 and the OEM for $263.70. You can also find compatible rear mufflers from your local exhaust and brake shops, probably for even less.

Dec 09, 2008 | 1996 Saab 900

1 Answer

Replacing ignition switch on Saab 1996 900s 2.3 I 5 speed


You take all the center console and plastic ducts from between the seats. There are 4 10mm bolts holding the shifter mechanism to the floor. Take these off and do your best to flip the whole housing to where you can access the bottom side. The ignition switch is attached under there. As I recall there are 2 T20 screws holding it on.

Oct 08, 2008 | 1996 Saab 900

Not finding what you are looking for?
1996 Saab 900 Logo

Related Topics:

453 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

rgbypoet

Level 2 Expert

161 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...