Question about 1993 Toyota Camry V6

1 Answer

How to remove ignition cylinder from Toyota Camry 1993

Ignition Cylinder

How do you replace the ignition cylinder in a 93 Toyota Camry?

Posted by on

  • 11 more comments 
  • jasonbul1981 Jan 20, 2009

    how to remove ignition cylinder from buick regal 1995

  • Moises espaeza
    Moises espaeza Dec 29, 2013

    Need info on 1998. Not 1993

  • Anonymous Mar 12, 2014

    ignition coil location

  • Anonymous Mar 12, 2014

    Single light does not / work o'm my 93 toyota Camry

  • Anonymous Mar 13, 2014

    Where the si gle light relay fou nd on a 93 toyotA camry

  • Anonymous Mar 14, 2014

    Is the 1993 Toyota Camry OBD 2 compliant?

  • Anonymous Mar 14, 2014

    Don't know where the OBD is

  • Anonymous Mar 14, 2014

    1993 Toyota Camry 4 Cylinder Open Circuit Relay might be the problem

  • Anonymous Mar 14, 2014

    replacing toyota camry 1993 generator

  • Anonymous Mar 15, 2014

    how to replace a ignition control module on a 1994 Toyota camry

  • Anonymous Mar 16, 2014

    How do I reset the immobiliser on my 2012 Toyota Camry keyless ignition?

  • Anonymous Mar 19, 2014

    How do I remove 120 amp alternator fuse

  • Anonymous Mar 28, 2014

    the keys have already been replaced

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 98 Answers

Here are step-by-step instructions for the removal and re-installation of your ignition cylinder on your Toyota. Hope this sheds some light on the subject and solves your problem. Have a great day!




  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle.
CAUTIONSome models covered by this guidemay be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in .
  1. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  2. Remove the screws which secure the upper and lower halves of the steering column cover.
  3. Turn the lock cylinder to the ACC position with the ignition key.
  4. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.).
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  1. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  2. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing.
To install:
  1. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  2. Secure the switch with its screw(s).
  3. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  4. Install the steering column covers.
  5. Connect the ignition switch wiring.
  6. Connect the negative battery cable.

Posted on Nov 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the ignition cylinder on my 2002 Toyota Rav 4 without the key?


from another post, psoted by James Allmond

How to remove ignition cylinder from Toyota Camry 1993

Here are step-by-step instructions for the removal and re-installation of your ignition cylinder on your Toyota. Hope this sheds some light on the subject and solves your problem. Have a great day!




  1. Disconnect the negative battery cable. If equipped with an air bag, wait at least 90 seconds before working on the vehicle.
CAUTIONSome models covered by this guidemay be equipped with a Supplemental Restraint System (SRS), which uses an air bag. Whenever working near any of the SRS components, such as the impact sensors, the air bag module, steering column and instrument panel, disable the SRS, as described in .
  1. Remove the lower steering column cover. Unfasten the ignition switch connector under the instrument panel.
  2. Remove the screws which secure the upper and lower halves of the steering column cover.
  3. Turn the lock cylinder to the ACC position with the ignition key.
  4. Push the lock cylinder stop in with a small, round object (cotter pin, punch, etc.).
On some vehicles, it may be necessary to remove the steering wheel and combination switch first.
  1. Withdraw the lock cylinder from the lock housing while depressing the stop tab.
  2. To remove the ignition switch, unfasten its securing screws and withdraw the switch from the lock housing.
To install:
  1. Align the locking cam with the hole in the ignition switch and insert the switch into the lock housing.
  2. Secure the switch with its screw(s).
  3. Make sure both the lock cylinder and column lock are in the ACC position. Slide the cylinder into the lock housing until the stop tab engages the hole in the lock.
  4. Install the steering column covers.
  5. Connect the ignition switch wiring.
  6. Connect the negative battery cable.

source

How do remove the ignition cylinder on my 2002 Toyota Rav 4 without the key

Jul 28, 2016 | Toyota Cars & Trucks

1 Answer

How to replace ignition coil on 93 sunbird?


you have to remove the intake tube and then it should expose the ignition system on the drives side of the cylinder head... or... follow the spark plug wires...

Nov 09, 2014 | 1993 Pontiac Sunbird

1 Answer

93 toyota camry ignition lock up


try turning steering wheel back and forth while turning the key if does not make it turn you will need a key tumbler ,possible repair by a lock smith

Jan 25, 2013 | 1993 Toyota Camry

1 Answer

I have a 1999 toyota camry and my key in the ignition cylinder wont turn i moved steering wheel and its on park do ineed to replace ignition cylindern


If the key will not turn the lock cylinder and you have removed the switch, you probably need a new cylinder.

Sep 07, 2012 | 1999 Toyota Camry

2 Answers

1993 Toyota Camry


93 Camry fuel filter is right below the brake master cylinder

Aug 08, 2009 | 1993 Toyota Camry V6

1 Answer

IM HAVING PROBLEMS GETTING THE OLD IGNITION OUT. THE IGNITION IS COMING OUT OF A 1996 TOYOTA CAMRY. WHAT DO I NEED TO DO?


You may have to drill out the lock pin in the cylinder. This is the pin that you have to push in to remove the cylinder.

Mar 23, 2009 | 1994 Toyota Camry

1 Answer

Ignition key cylinder


You have to have the ignition lock exposed, take the covers off above and below the lock body that holds the cylinder.
Insert the key fully into the keyway, and turn it to ACC. On the ignition lock body, press on the "stop pin", that pokes out of the lack body, above where the cylinder is housed. Press on the "stop-pin", and extract the cylinder. If the key can not be turn ed to ACC, the cylinder will not come out.
Thanks for choosing FixYa. Please let me know if this solves your problem.

Dec 16, 2008 | 1993 Toyota Tercel

3 Answers

1998 toyota


There is a pin that you have to push in on the bottom of the lock cylinder housing.It is recessed in a hole.You have to turn the key to acc or on to get it to push in.Once you push it in you can pull the key and lock cylinder out.

Dec 01, 2008 | 1998 Toyota Camry

Not finding what you are looking for?
1993 Toyota Camry V6 Logo

4,015 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...