Question about 1991 Chevrolet C1500

1 Answer

I dont know how to put the spark plugs on the wroter right

Posted by on

  • Anonymous Jan 13, 2009

    need picture of spark plug wires on 4.3 v6



1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.


    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 121 Answers

Did you mean, on the distributor cap? If its a v8, firing order is 1-8-4-3-6-5-7-2, in a clockwise rotation. If it's a v6, 1-6-5-4-3-2 in a clockwise rotation. Usually you start at #1, which should be the forward most post on the cap, pointing in the general direction of #1 cylinder. #1 cylinder on a Chevy is the L/F cylinder. All the odd # cylinders are on the left, and even #s on the right.I hope this helps.

Posted on Nov 23, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My 1991 toyota celica is loading up on oil inthe spark plug tube and shoting out the plug wire, have replace valve cover ,seal twice last one came from the dealer try lite torque ,pay another mechanic and...

you need to take the valve cover back off and right below the threads on the 4 nuts that hold the valve cover on take a small chain wrench and unscrew the spark plug tubes out of the cylinder can then clean the hole out where the tubes screw in with brake clean to get all of the oil out and leave the spark plugs in while doing this so you dont fill the cylinders up.......then clean the threads up and get some liquid white teflon paste to put on the threads and put tubes back in but try not to over dont want to crush the tube cause you want be able to get a spark plug socket in to change the plugs.....just snug them up.....i hope that this was the info that you needed....let me and fixya know if i was any help to you and a thumbs up and a comment would be appreciated.....good luck and have a blessed day......they make a special tool to take the tubes out but the small chain wrench works much better and faster......if i can help in any other way let me know......

Jul 30, 2011 | 1990 Toyota Celica

1 Answer

I dont know how to change the sprak plugs and is very expencive, please help, I broke and I want to do it my self

its not that hard al you got to do is get a spark plug socket there is going to be two sizes your going to need the smallest one and just follow the spark plug wires to the spark plugs and then take them out but make sure you put the new wire on right when you take the old one off so you dont mess up the fireing order

Nov 05, 2009 | 1996 Plymouth Grand Voyager

1 Answer

Placement for spark plug wires for 1995 chevy blazer 4wd

i didnt fix it on my own couldnt get the diagram from you your site only gave me a ad for hp printers
i had to take it to a garage to take care of it i dont know if i hit the wrong link let me know

Jun 18, 2009 | 1995 Chevrolet Blazer

1 Answer

My 1990 mariner 75 hp is only running on top cylinder.

reed valves either need cleaning or renewing

Apr 11, 2009 | 2003 Mercury Mariner

2 Answers

I need to change the spark plugs and i dont know where to start?

Go through your spark plug wires and mark which plug it is on. Once you have done this then you can pull the wires off each spark plug. Once the plug wires are off take a spark plug socket and gently apply some pressure to loosen the spark plug. Once its loose you should be able to reach down and remove the plug by hand. Once you have the plug off grab your new plug. Make sure it has the correct gab setting for your engine size and then install the new plug. once you have the new plug in gently snug it down. Do this with the rest of your plugs. Once all your plugs are in place and snugged down then put your plug wires back on each plug (This is where the labeling comes in handy). It is also a good idea to get a good set of plug wires and just replace them while you are at it.

Apr 01, 2009 | 1987 Ford Bronco

1 Answer

Firing order

If you pulled all the wires at once, you will need to go to a parts store and see if they can show you a diagram on how to reset the wires. Do not unhook the wires from the spark plugs at this point.

Feb 14, 2009 | 1987 GMC VanDura

1 Answer

Spark plug wire diagram

hi try this you will have to save to file then zoom in to read.

Jan 31, 2009 | 1997 Chevrolet Monte Carlo

2 Answers

Ihave changed the spark plugs but i dont know if put the caps in

Not sure what you're asking. The only order that matters is the order of the spark plug wires. There isn't an order for the spark plugs themselves. So are u looking for the order of the spark plug wires?

Nov 12, 2008 | Honda Civic Cars & Trucks

2 Answers

Ihave changed the spark plugs but i dont know if put the caps in

1-3-4-2 number 1 is the first one on the left side

Nov 12, 2008 | 2005 Honda Civic

Not finding what you are looking for?
1991 Chevrolet C1500 Logo

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides