Question about 1995 Volkswagen Jetta

1 Answer

Need to know how to remove the back panel by the rear window

I am trying to change the strusts and I need to know how to remove the back panel without damaging it.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Back panel? I assume you are referencing the fender liner? if so there should be some 8MM bolts holding it in. also to replace the struts and not the springs you will need a couple of specialty tools show here:
http://zdmak.com/wbstore/main.asp?action=PROD&PROD=MK-4491A&CTMP=1&LowCt=0
and here: the slotted strut nut tool
http://www.germanautoparts.com/Tools/Volkswagen/Suspension+tools

Posted on Jan 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change out the sub woofer in the back


To get at the speaker, you need to remove the rear window shelf trim panel -
Remove rear seat lower by lifting from front;
Remove bolts holding rear seat back and remove seat back; Remove the seat belt retractors;
Remove the push in retainers from the cross car beam;
Lift up on the front of the shelf panel to disengage the hook and loop material; then do the same at the rear of the panel, and pull out the shelf.
The speaker is now accessible for removal.

Feb 07, 2015 | 2001 Cadillac DeVille

1 Answer

Passenger side rear window is off track, will not stay up or operate. Need to know how to remove door panel without damage


Please see my tip at http://www.fixya.com/cars/r6065762-removing_door_panels . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.

Oct 10, 2010 | 2001 Oldsmobile Aurora

1 Answer

Resr window wiper is corroded and moves very hard, needs lubed


you need to take the interior trim panel off. the whole motor and shaft and bolted from the inside.

Jul 24, 2010 | 2005 Ford Expedition

1 Answer

Need diagram on how to R&R rear door panel 2002 Cadillac Seville


You can either go to google ebooks and find a free repair manual for your car, or go to autozone.com and register for free online repair manual.

You will need to remove all screws, then remove window and lock controls, then take large flat-tipped screwdriver and gently pry next to all the plastic studs that hold on panel to door. Once all panel is pried up and loose, just pull straight up and lift off. Then remove plastic without ripping the middle, (You can stick back on later) then you will have access to window motor. It is a 12 volt motor.

Oct 06, 2009 | 2002 Cadillac Seville

1 Answer

Right rear window is off the tracks. How do I remove the panel?


if the window is off track the regulator is probably bad. to remove the door panel should be a couple of screws by the inside pull handle and possibly one by the door handle itself also check the bottom of the door for any then just pull it off and lift up to clear latches and remove plastic film to get to inside of the door

Aug 30, 2009 | 2001 Oldsmobile Aurora

1 Answer

Remove rear passnger rear door panel 1991 honda


As I remember, you need to remove the front seat belt mount, & completely remove the back seats, in order to remove the rear door cards, without breaking them.
Have fun;)

Jul 17, 2009 | 1991 Honda Accord

1 Answer

REAR DRIVER'S SIDE DOOR PANEL


plastic clip on back of handel , hard to remove without right tool , but can be done

Jun 01, 2009 | 2004 Pontiac Grand Prix

6 Answers

How to make rear power windows on police interceptor operational


pull the b pillar cover off next to the driver's seat, there will be a connector with 2 red wires mounted to the b pillar right next to the seat belt retractor, find the other connector, and connect them. should operate normally.

Jan 28, 2009 | 2003 Ford Crown Victoria

1 Answer

Changing rear struts


You need to remove the rear seat bottoma and the rear seat backs. Then, remove the inner panels that are on either side of the rear of the car. Then you will see the top bolts.

Jan 12, 2009 | 1996 Toyota Camry

1 Answer

'92 Probe, power window regulator


You do not need to remove the back seat. You do need a long extension to remove the lower bolt holding in the bottom of the rear window. Two bolts at the top are easy to see and remove. Then unplug the wires and the entire window assembly will wiggle out without any other disassembly.

Jun 23, 2008 | 1992 Ford Probe

Not finding what you are looking for?
1995 Volkswagen Jetta Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60769 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...