Question about 1997 Oldsmobile 88

1 Answer

Computer control module

Hi guys, help, I have a 1997 oldsmobile 88. Have a problem with it,
took it to Autozone to plug into the computed to see what's wrong and they could not find where the plug is to connect it to the computer. Any ideas?

Thanks, Luisa

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the same car... took it to our local autozone and they had no problem finding it. It was located under the steering wheel someplace. Not exactly sure of the location, but they didn't have any problem locating it.

Posted on Dec 08, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1995 oldsmobile 88 and the computer needs to be reset.


Hi Dave.

You can perform a reset of main control module (ECM) disconnecting the battery terminals for a couple of minutes. That will reset the check engine light until the problem occurs again. Make sure that you have the stereo anti theft code if needed.

The proper way to reset the DTC codes is using an OBDII scanner. The job can be done at the dealer place or at any authorized garage for a small fee (half hour labor). In US the scan and reset can be done for free at Autozone. If possible go to the nearest Autozone, ask to do a code scanning take note of codes and ask to reset the ECM.

Finally, you can reset the codes at home using a scanner tool like this:OBDII Scanner - U480.

Regards



Regards.

Ginko

Sep 09, 2011 | 1995 Oldsmobile 88

3 Answers

Where is the engine computer located


Engine Control Computer is located in the front seating area, passenger side, under dash, mounted behind kick panel

Jul 07, 2011 | 1988 Oldsmobile Delta 88

2 Answers

Cannot locate the ecm for my 88 olds custom cruiser. can you help?


For 1988 Oldsmobile 88 Custom Cruiser 5.0L 4BL OHV 8cyl the Engine Control Computer is located front seating area, passenger side, under dash, mounted behind kick panel.

Hope helps (remembeer to rate this asnwer)

Jan 10, 2011 | 1988 Oldsmobile Cutlass Supreme

3 Answers

1997 Olds Delta 88, 3800 engine, when started and let idle, when the engine hits about 150 degrees, it stumbles and kills. It starts back up. It has killed at freeway speeds several times. Pull off the...


electrical is the weakest link-you may have a computer with issues and before replacin a reprogram should be considered--what did vehicle scan tell you? Data recorders are often placed in cars that show no codes--Older cars can have solenoids and components that heat up and stop engine--if theres a distributer cap-inspec for corrosion

Nov 29, 2010 | 1997 Oldsmobile 88

1 Answer

Where is the ECM located on the '94 Olds 88 Royale?


For 1994 Oldsmobile 88 3.8L SFI OHV 6cyl the Engine Control Computer is located front seating area, passenger side, under dash, mounted above kick panel.

Hope helps (remember to rate this).

Nov 09, 2010 | 1994 Oldsmobile 88

1 Answer

Does a 1994 olsmobile 88 have a modulator valve?


no the tranny is computer controlled.

Aug 09, 2010 | 1994 Oldsmobile 88

3 Answers

1998olds 88 running rough and check engine light flashing


Have you had the engine codes pulled. Usually when you replace an O2 sensor you would have to replace the converters

Aug 15, 2009 | 1998 Oldsmobile 88

1 Answer

Check engine light came on Autozone said needed EVAP purge solenoid?


The problem is, Autozone doesn't use a scanner. They use a scan tool otherwise known as a code reader. I suggest get another opinion at a shop with an actual scanner. They would be more helpful to you. Don't just throw parts at it.

Jun 11, 2008 | 1997 Oldsmobile 88

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...