Question about 1992 Honda Accord

1 Answer

I need instructions on how toremove ingnition to install a new one....

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 314 Answers

Remove the covers on the steering around the switch. Do not force anything!! Keep track of what screws go back in as you may find a few different. Unplug the wire socket. You will find 4 screws. Be caefull when you remove the shaft going down the steering . The rest is no prob! Frankster016

Posted on Nov 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Engine cranks but no start, no spark. What else can I check?


is it actually rotating when the engine turns over I know sounds stupid but I\'ve seen the teeth that goes inside against the cam break off on first turn over happened to me once on a Honda, also that same car my original problem was I was getting power and everything like you but the icm on the distributor was putting the power out on the ground side and the power turned to ground not allowing the distributor to do its job and produce spark





hope this helps

Aug 29, 2014 | 1994 Toyota Corolla

1 Answer

My ingnition coils are bad 6 & 4


Buy new ones and install them. Seems you already have the diagnosis.

Jan 16, 2011 | 1998 Lincoln Navigator

1 Answer

My pontiac grand prix will not turn over the starter is ok i also have changed the ingnition switch with no luck any ideas


Please see my tip at http://www.fixya.com/cars/r6222268-engine_doesnt_crank_turn_over . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.

Oct 08, 2010 | 2004 Pontiac Grand Prix

1 Answer

Need to know how to instal the horn contact and spring into a 1984 camaro steering colum


First you need toremove the steering wheel. You will also need a lock ring removal tool. This tool will help you remove the circlip from behind plastic cover. Dont lose this clip.After you have removed the lock plate then the horn ring should be visible and you can replace it.

Apr 27, 2010 | 1984 Chevrolet Camaro

2 Answers

1965 T-BIRD, RECENTLY INSTALLED NEW STARTER , BATTERY


sounds like you alternator is not charging. that would cause your concern.

Sep 06, 2009 | 1983 Ford Thunderbird

1 Answer

I installed a new ignition switch in my 1988 mustang


there is a ingnition rod going from key switch to ingnition switch ,it is probly not in the slot any more or the ingnition cam is broken

Jun 28, 2009 | 1988 Ford Mustang

1 Answer

Key stuck in ingnition


Nicole you need a new key lock installed.  A locksmith or the dealer can do it. 

Mar 25, 2009 | 2000 Mazda Millenia

1 Answer

I need instructions on how to put a locksmart switch ingnition


this not something that a back-yard mechanic should tackle

Mar 15, 2009 | 2002 Ford SVT Focus

1 Answer

I need instructions on how to put a locksmart switch ingnition


Removal
  1. Disconnect battery ground cable. Remove the steering column shroud by removing the four or five self-tapping screws. Remove tilt lever (if so equipped).
  1. Remove instrument panel lower steering column cover.
  1. Disconnect the ignition switch electrical connector.
  1. Rotate ignition key lock cylinder to the RUN position.
  1. Remove the two screws retaining ignition switch.
  1. Disengage the ignition switch from the actuator.
Installation
  1. Adjust the ignition switch by sliding the carrier to the switch RUN position. NOTE: A new replacement switch assembly will be set in the RUN position as received.
  1. Check to ensure that the ignition key lock cylinder is in the RUN position. The RUN position is achieved by rotating the key lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch into the actuator. It may be necessary to move the switch slightly back and forth to align the switch mounting holes with the column lock housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is locked in the LOCK position.
  1. Install instrument panel lower steering column cover.
  1. Install the steering column trim shrouds and tilt lever (if so equipped).

Feb 26, 2009 | 1991 Lincoln Town Car

1 Answer

Ammeter wiring for a 86 F-150


try here "http://www.autozone.com/addVehicleId,1127902/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c1528004bb9d"

Nov 21, 2008 | 1985 Ford F150

Not finding what you are looking for?
1992 Honda Accord Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21984 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...