Question about 1995 Chevrolet Corsica
I have a 95 chevy corsica with power door locks. It has the auto locking safety feature when you put it in gear. It did'nt have a manual with it so I don't know how to disable that feature. Thanks in advance for any info.
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
you have to take it into the dealership for a 1999. the dealer needs to change the settings in the BCM (body control module). in 2000, the BCM came preprogrammed to allow the owner to change the door lock settings at home. unfortunately for a 1999, it has to be done at the dealership.
Posted on Jan 07, 2009
SOURCE: 04 Chevy Aveo Lock
I just fixed my 2005 Aveo door lock. like so many it fell in to the inside and was hitting the window rod and locking. The fix was not to bad, I removed the 3 screws on the bottom door panel, one in the center of door pull and the one behind the arm pull. Then the door panel can be pulled out and up to unhook it from the window seam. I did not un hook the linkage from the door handel, I just slid panel down and let it hang to the side. Then peel the water film back so you can reach in and get the key lock back in to the hole. I found that my lock had rotated down and needed to be rotated back so the screw arm lines back up with the screw hole. I found a replacement screw in my screw tin that worked, tested it and it worked fine. Just revers the door panel removal proceduer making shur that the two hooks on back of the door handel cup is hooked into the two slots on door frame ot it will stick out and you will not be able to put the one screw in, dun deal.
Hope this helps
Posted on Jun 15, 2009
SOURCE: door locks and power window
Just did this procedure I got from coloradofans.com forums:
"any type of power/voltage change seems to trigger this issue
The most common symptom is power locks fail and only the driver window quits, however that is on the extended cab.
Steps to fix and it works every time.
take door panel off driver's door
Disconnect the wiring attached to window and power lock control unit
disconnect battery cables
connect the negative to the positive cable(((NO BATTERY CONNECTED)))
This will act to short residual voltage in the system
5 minutes later
place the key in the ignition and turn to the run position
connect the wiring to the window/lock controller
connect the negative cable to the battery
then the positive
open drivers side door
turn key to the off position((do not remove yet)) you should get a series of dings through speakers telling you the key is still in the ignition
once it begins dinging pull the key out and you should hear the door lock solenoids trigger and the windows should work." - Coloradofans.com forums
Posted on Mar 20, 2010
Tips for a great answer:
Aug 09, 2015 | Lexus RX 300 Cars & Trucks
Jul 14, 2015 | Nissan Cars & Trucks
Feb 14, 2013 | Cars & Trucks
Apr 24, 2010 | 1995 Toyota Camry
Mar 03, 2010 | 2007 Honda CR-V
Feb 22, 2010 | 2005 Chevrolet Equinox
Feb 18, 2010 | 2007 Honda Accord Sedan
May 09, 2009 | 1997 Chevrolet S-10 Pickup
Mar 22, 2009 | 2005 Chevrolet Suburban
Sep 19, 2008 | 1995 Jeep Cherokee
65 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: