Question about 1994 Land Rover Range Rover County

1 Answer

My 1994 rrc starts but wont stay runing

I have a 94 rrc lwb 4.0 i put a new tranny in it and got it all back together and i started it . Now my issue is it starts but does not wanna stay running or idle it sounds like a miss but its will start just fine ive done nothing to the engine it ran just fine the yoke broke on the transfercse and blew a hole into the side of my tranny thats why i put a new one but it ran just fine . Ok another thing it brought up 2 codes the first code was 02 and the second was 03 wut do they mean anyone can you help me . The rover will like i said start but it runs as if its being choked out or misfiring it starts then emediatly dies can you guys plz help me out its my only car thankx

Posted by on

  • holeshot_63 Nov 23, 2008

    its getting feul and spark everything is new it just got seviced so maybe you can help me out



1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

99.9% sure that it is your mass air flow sensor

Posted on Dec 12, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Wobt start

94 cherokee
wont start
but does it crank , there are 4 steps
cranks, starts, runs and sustains running. 4 steps.
how far do you get?
tranny, that is right all A/T have a PRNDL switch that does fail
and all do and all , fails kill the KEY line to the starter,.
causing, step 1 to fail not cranking

Jan 15, 2014 | 1994 Jeep Cherokee

1 Answer

94 jeep grand cherokee, trannys slippg in 1s gear, added lucas stop slip, started next day, drve a few feet and it wont engage.......

Transmission might be fried. One suggestion, did you try putting it in 4WD and trying that? I had a Jeep come in, same thing, wont move, ended up being a blown transfer case. Put it in 4 hi or low, and see if it will go into gear and move. Long shot, but worth a try.

Dec 29, 2013 | 1994 Jeep Grand Cherokee

1 Answer

Hello fix ya, I have a 94 lt1 Camaro with a 4l60e. It had no 3/4 gear. So I dropped it and took apart and clean it up. I put bogg Warner clutches in it. It had reverse, 1,2 but slipped outta 3rd. Now that...

When you put the shift module back on the side of tranny did u line it up right if so are you sure you put the tranny together right? When u take off the shift cable it has to be line up right to shift inreverse if u put car in reverse will it start if so you have not lined up right u really meed a chilton book to look at its hard to explain on forum

Feb 19, 2013 | Cars & Trucks

1 Answer

Help me please !!!!! timing belt issues!!!

check for any sensors left disconnected ,if this is a 94 then the chances are the sensor is on the front pulley and it hasnt been re-connected ,also it may have a cam sensor .get the person who changed the pump back to put it right why did you let them leave without the car starting

Apr 14, 2012 | Mitsubishi Cars & Trucks

1 Answer

My rpms wont go over 3000 on my 94 toyota 4 runner.

the V6 has a rev limiter in gear that keeps it under this in first gear. put the tranny in Power mode if it's an automatic. it will **** more gas, however.

Apr 13, 2009 | 1994 Toyota 4Runner

1 Answer

Changed timing belt 94 civic ex 1.6, now wont start

first make shure the fireing order is correct 1 3 4 2, make shure you have the timeing set right

Apr 02, 2009 | 1994 Honda Civic

2 Answers

Car ill not start

you need the electrical part of the ignition switch this is a common problem on this model.

Mar 21, 2009 | 1994 Acura Legend

1 Answer

Range rover classic lwb 4.0

Check your earth wires on the gearbox and engine , check that no air intake pipes or vacuum hoses have come off with the engine tilting when you replaced the gearbox.Also check the brake vacuum hose.

Nov 23, 2008 | 1994 Land Rover Range Rover County

Not finding what you are looking for?
1994 Land Rover Range Rover County Logo

208 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22359 Answers


Level 3 Expert

81400 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides