Question about 1999 Plymouth Breeze

2 Answers

Wont start it will crank over but it will not start things i have already done changed plugs

Posted by on

  • 3 more comments 
  • hotrod1339 Nov 23, 2008

    very little no it does not fire and 2.4

  • irbchicken29 Nov 25, 2008

    just put new plugs, ignition coil, thermostat, thermostat housing on and now it will not start. It will turn over, but getting no fire.

  • admiralbritt Jan 15, 2009

    wont start new pulgs but will turn over

  • irbchicken Jan 30, 2009

    The car will turn over but will not fire. Already changed plugs and wires, and put a new ignition coil on.

  • Theresa Fay Apr 02, 2009

    It won't start. I turn the key and nothing.

    the power windows,power locks, dome lights, headlights, blinkers, hassards, the fans to the heater and air are working when the key is turned.



    I have no radio, dash lights and It just won't start.

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Find someone with a diagnostic computer. and have it tested . my 99 plymouth breeze is doing the same thing.i found out it was a cam sensor. now i just need to find out where the cam sensor is located.

Posted on Mar 18, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 85 Answers

Does it have fuel pressure how much. does it have fire. need to know. what engine does this have.

Posted on Nov 23, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My question what is the problem of bmw car 5 series engine wont start but has cranking?someone pls give some advice


When were your spark plug wires last changed? And have you checked your ignition module? Crank shaft position sensor is another item to have checked.

Oct 08, 2016 | 2009 BMW 530i

1 Answer

Truck wont start after changing the spark plug and wires


It's already not start before you changed or after changed ?
If before. the timing belt or might be broken , burn fuel pump's fuse, injector's fuse or main engine relay.
If after. It's possible miss some wire that still not connect.

Mai

Feb 26, 2013 | 1986 Ford Bronco

1 Answer

I have a 2003 Oldsmobile Alero 3.4L that wont start. I have done fuel pressure test 50-55 psi and plugs have good spark. However when done light test on injectors there is no response so there is no pulse....


Is the security light staying on ?
Usually the engine will not crank and you have no power to the fuel pump if the security system is disabling the car.
No injector pulse but spark would point to the computer since both use input from the crank and cam sensors.

Dec 22, 2012 | Cars & Trucks

1 Answer

My car starts but it wont stay running, I changed oil, spark plugs, and fuel pump, Could it be i have a bad fuel pump??


Yes it could be a failing fuel pump, but it could also be several other things. If you haven't already done so a good place to start would be to check for trouble codes stored in the computer.

Jan 31, 2011 | 1995 Chevrolet Caprice Classic

1 Answer

It usually cranks and starts within seconds, every other day it will crank and crank and crank before starting, pressing the gas pedal doesn't seem to help or hurt, I'm afraid one day it will crank until...


your vehicle is fuel injected you should not have to pump the gas pedal plugs and wires ill bet that solves your problem and changeing the fuel filter wont hurt and a fuel injection cleaning wont hurt if you havent had one done to it

Nov 30, 2010 | 2002 Ford Expedition

1 Answer

97 Toyota Camry Has been having issues lately. First it started to miss fire a lot kept getting the code p1300 so i was advised to get a tune up i did that. Tune up included spark plugs changed, wires...


Has anyone checked the Crank position sensor or knock sensor? If the Crank position sensor isn't reporting the correct position of the crank when it turns the spark plugs are firing at the wrong time. This could be because of a worn timing belt or faulty timing belt tension arm. Have the sensors checked and if they are good your left with replacing your timing belt.

Oct 16, 2010 | 1997 Toyota Camry

1 Answer

Engine cranks,has spark,fuel and oil pressure.changed oil pressure switch,crank and cam sensor,spark plugs and ignition relay.checked electrical connections and all fuses.


most cars have a mass airflow sensor.try reploacing that,That is the only other thing i can think of besides what was already replaced. if this does not work get a compression test done on the car.

Feb 09, 2010 | 2006 Nissan Sentra

2 Answers

No spark


Possibly the crank sensor.

Jun 02, 2009 | 1996 Chevrolet Silverado 2500

1 Answer

Change spark plugs and now car wont start.....1994 ford tarus


Do you have the "firing order" correct? In other words, is each spark plug wire going to the same cylinder it was on before you changed the plugs? If you have done nothing else but changed the plugs then this is the most likely problem.
If when you try to start the car it backfires through the exhaust or backfires through the intake. Then this " IS" the problem. Good luck.

May 23, 2009 | 1994 Ford Taurus

Not finding what you are looking for?
1999 Plymouth Breeze Logo

410 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...