Question about 1998 Kia Sephia

1 Answer

Coolant temperature sensor on 98 kia sephia

Where to find it and how to remove and install a new one

Posted by on

  • Anonymous Mar 27, 2014

    when temperature is high the fan will not turn

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Kia Master
  • 6,674 Answers

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the camshaft position sensor located on a 98 Kia Sephia?


check on this site - general location regardless of the make is on "other end" of the engine, parts as well on this site:
http://repairpal.com/camshaft-sensor

some parts here:
http://www.redlinemotive.com/store/replacement/model.asp?ct=A&make=KI&year=1998

hope this will help you - do not forget to vote...

Mar 27, 2015 | 1998 Kia Sephia

1 Answer

Trouble locating cooling sensor on 2003 gmc envoy


4.2L Engine To Remove:
  1. Disconnect the negative battery cable from the battery.
  2. Drain the coolant from the engine.
  3. Disconnect the engine coolant temperature (ECT) sensor connector. Engine coolant temperature sensor removal and installation gm-04-42-1509.gif

  4. Remove the engine coolant temperature (ECT) sensor from the engine.
To Install:
  1. Apply thread sealer P/N 12346004 or equivalent to the engine coolant temperature (ECT) sensor threads.
  2. Install the engine coolant temperature (ECT) sensor into the engine. Torque the sensor to 12 ft-lb (16 Nm).
  3. Connect the engine coolant temperature (ECT) sensor connector.
  4. Refill the engine with coolant.
  5. Connect the negative battery cable to the battery.
5.3L & 6.0L Engines To Remove:
  1. Drain the coolant from the engine.
  2. Disconnect the engine coolant temperature (ECT) sensor connector. Engine coolant temperature sensor removal and installation removeect.gif

  3. Remove the engine coolant temperature (ECT) sensor from the left cylinder head.
To Install:
  1. Apply thread sealer P/N 12346004 or equivalent to the engine coolant temperature (ECT) sensor threads.
  2. Install the engine coolant temperature (ECT) sensor into the left cylinder head. Torque the sensor to 15 ft-lb (20 Nm).
  3. Connect the engine coolant temperature (ECT) sensor connector.
  4. Refill the engine with coolant.

Jul 08, 2010 | 2003 GMC Envoy

1 Answer

Electric cooling fan not working?


SCAN CAR FOR A FAULTY COOLANT TEMPERATURE SENSOR.IF SENSOR GOOD CHECK COOLING FAN FUSE AND RELAY.IT BOTH OKAY.HOT WIRE COOLANT FAN USING JUMPER WIRES TO BATTERY IF FAN DONT WORK REPLACE THE FAN MOTOR.IF COOLANT TEMPERATURE IS BAD REPLACE IT.BECAUSE IT CONTROLS THE FAN TURNING ON WHEN COOLANT GETS A CERTAIN TEMPERATURE.

May 04, 2010 | 2001 Kia Sephia

2 Answers

How to replace knock sensor 2000 kia sephia


remove intake manifold support bracket. unpug the sensor then take the bolt that holds it out then reverse to relace

Apr 05, 2010 | 2001 Kia Sephia

1 Answer

What do the codes PO455 and PO128 mean on my kia sephia? I was told my fuel canister is only purchased at dealer ...is that true>


P0455= Evaporative Emission System Leak Detected (large leak)
P0128=Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature)

Nothing here says buy a new can!
it could be as simple as turning the gas cap three clicks past tight,that is a very common thing,The other thing shows you should change your thermostat

Dec 24, 2009 | 2001 Kia Sephia

1 Answer

Water pump in a kia saphea how do u change it 2001


Hi there,

Below are the steps..

Disconnect negative battery cable.
3b9f19b.jpg

Drain engine coolant.
1eadff0.jpg

Remove timing belt (please make sure you know how to do this, otherwise, seek help from a certified mechanic) Remove tensioner and idler. f644145.jpg Remove water pump. dbfdc5c.jpg Remove any gasket fragments, dirt or oil from sealing surfaces. Install new gasket on water pump. To prevent dropping the gasket when installing, put sealant in gasket groove. But do not apply to sealing surfaces. Install water pump. Install tensioner, idler and timing belt. Fill engine coolant. Connect negative battery cable. Start engine and check for leaks. Regards, Jeep Brainy

Sep 09, 2009 | 2000 Kia Sephia

2 Answers

'99 Kia Sephia overheats and coolant boils out...


rplace coolant temp sensor,and bleed all air out of coolant system ,fan relay checks and fuses check is good,,do fans run with ac on? if they do ,fuse and relay most likely ok but check relays any way

Jul 04, 2009 | 1998 Kia Sephia

1 Answer

98 kia sephia will not start


is it a stick could be your clutch switch or netural saftey switch possibly ignition switch

Jun 16, 2009 | 1994 Kia Sephia

Not finding what you are looking for?
1998 Kia Sephia Logo

Related Topics:

403 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60867 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...