Question about 1993 Chevrolet S-10

1 Answer

Problem code 22, runs like ****

Replaced throttle pos sensor, replaced fuel relay, replaced map sensor,
replaced computer(1228062) used my chips. seems to run better with a
vacuum leak.
disconnected map from vacuum port on throttle body and also the little thing that is connected inside aircleaner and plugged port,I Think it controls flapper in air cleaner horn. still same code 22
I created a vacuum leak in the large hose to the brake booster and it runs
good enough to use, but want to find the problem. help help help
1993 s-10 p/u 2.8 tbi

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Chevrolet Master
  • 60,769 Answers

YOU NEED TO PULL THE CONNECTOR OFF THE ECM AND RUN A CONTINUITY TEST OF THE WIRES FROM THE TPS CONNECTOR TO THE ECM, THIS SOUNDS LIKE A POSSIABLE WIRING PROBLEM TO THE TPS

Posted on Dec 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

94 jeep wrangler runs 45 seconds then shuts down


You will have to figure out what is quitting when the engine stops.
If you are loosing fuel to the injectors, it could be a pump relay, or something with the injectors.
If you can spray carb cleaner into the throttle body and keep it running, look for a fuel problem.

Dec 22, 2012 | 1994 Jeep Wrangler

3 Answers

Check engine light came on


What do you mean "can't find code"? If the check engine light is on, there is a fault code stored in your onboard computer - that's the way it works. If you are using a generic OBD code reader, that is most likely the reason you cannot find any codes. You need to use a scanner that has the correct software to access your ENTIRE computer network, not just the "continuous memory" or "generic" side of your computer system.

The window problem is a seperate problem and must be diagnosed accordingly.

Apr 23, 2012 | Daewoo Matiz Cars & Trucks

2 Answers

I have a jeep grand cherokee i have a code p1296. voltage missing at throttle position sensor.explanation engine running and the ecm detected map sensor voltage less than expected. probable cause open or...


I would change the TPS throttle position sensor and the Map/MAF are you sure its not the mass air flow?. I think your computer is fine it could be have a loose ground issues but computers dont go bad.

Sep 12, 2011 | 1997 Jeep Grand Cherokee

1 Answer

Is there a list for computer codes for 1980-1990's Chrysler Le Baron


Yes here is that list.
Chrysler products COMMON CODES OBD1 (vehicles made before 1995)
Part 1: Chrysler Domestic vehicles
CODES/Meaning
88 display used for start or test
11 camshaft signal or ignition signal, no reference signal during cranking
12 memory to controller has been cleared within 50-100 engine starts
13 map sensor not detecting any change during test
14 map voltage too high or too low
15 vehicle speed sensor, no signal detected
16 knock sensor circuit. open or short detected
17 low engine temperature, possible thermostat fault
21 oxygen sensor signal, neither rich or lean detected
22 coolant sensor voltage low
23 air charge voltage high/low detected
24 throttle positioner sensor voltage high/low
25 automatic idle speed motor driver circuit, short or open detected
26 injectors 1,2,3 peak current not reached
27 injector control circuit does not respond to control signal
31 purge solenoid circuit, open or short detected
32 egr solenoid circuit, open or short detected
33 a/c clutch relay circuit, open or short detected
34 speed control servo solenoid, open or short detected
35 radiator fan control relay circuit, open or short detected
36 wastegate solenoid, open or short detected
37 part throttle unlock(PTU) circuit, open or short detected
41 charging system circuit not responding to control signal
42 fuel pump or auto shutdown (ASD) relay voltage sensed at controller
43 ignition control circuit not responding
44 battery temperature voltage circuit problem
45 turbo boost limit exceeded-map sensor detects overboost
46 battery voltage too high
47 battery voltage too low
51 air/fuel at limit
52 logic module fault
53 internal controller failure
54 camshaft reference circuit not detected
55 end of message
61 baro read solenoid, open or short detected
62 emr mileage not stored
63 eeprom write denied
64 flex fuel sensor signal out of range
65 manifold tuning valve, open or short detected
66 no ccd messages
76 ballast bypass relay, open or short detected
77 speed control relay, open or short detected

May 31, 2011 | Chrysler LeBaron Cars & Trucks

1 Answer

I have a 1999 malibu it start and run for short time but them stop.if i started again them it dosent have any signal at the spark plug. it have been 2 days that this is goin up this mornig i started and...


map sensor control fuel delivery and ignition timing.the map sensor is your load sensor when engine closed throttle high vacuum wide open throttle low vacuum.need more fuel and spark.when your engine at wide open throttle. low vacuum.cause electrical volts to increase to 5 volts in which pcm will increase fuel pressure and spark.the map sensor does control spark also.replace map sensor erase code and see what happens.

Apr 16, 2011 | 1998 Chevrolet Malibu

1 Answer

Check engine code 55 jeep grand cherokee laredo v6 1997. transmission wont shift properly also pulling code 21 and i figured out that one is for the throtle position sensor


These are the fault codes for your Jeep below;

Jeep
11 IGN reference signal.
13 Fault in the map sensor pneumatic circuit.
14 Fault in the map sensor electrical circuit.
15 Fault in the vehicle speed sensor circuit.
17 Engine running too cool.
21 Problem in the oxygen feedback circuit.
22 Fault in the coolant temperature sensor circuit.
23 Air temperature sensor.
24 Fault in the throttle position sensor circuit.
25 Fault in the IAC motor drive circuit.
27 Fault in injector driver interface circuit.
31 Purge solenoid circuit.
33 Fault in air conditioning cutout relay circuit.
34 S/C solenoid circuits.
35 Fault in fan relay circuit.
41 Fault in the charging system or no field current.
42 Fault in the ASD relay driver circuit.
43 Fault in ignition coil control circuit.
44 Battery Temp Voltage.
46 Battery voltage is too high.
47 Battery voltage is too low.
51 Lean condition is indicated.
52 Rich condition is indicated.
53 Internal problem in module.
54 Fault in the distributor high data rate pickup circuit.
55 Completion of fault code display.
62 Unsuccessful attempt to update EMR mileage.
63 Unsuccessful attempt to write to an EEPROM location by the controller.
76 Fuel pump resistor by-pass relay circuit

Mar 08, 2011 | 1997 Jeep Grand Cherokee

1 Answer

What is the 1987 pontiac fiero gt v6 check engine light code list?


CODE 12- NO DISTRIBUTOR REFERENCE PULSES ECM. CODE 13- OXYGEN CIRCUIT. CODE 14- COOLANT SENSOR HIGH TEMP CODE 15- COOLANT SENSOR LOW TEMP. CODE 21 - THROTTLE POSITION SENSOR VOLTAGE HIGH.CODE 22 - THROTTLE POSITION SENSOR VOLTAGE LOW.CODE - 23 MIXTURE CONTROL SOLENOID.FOR CARBURETOR ENGINE. CODE 24 -VECHICLE SPEED SENSOR. CODE 32 - BARO CIRCUIT LOW.CODE 32 - FUEL INJECTED EGR VALVE VACUUM SWITCH SHORTED TO GROUND.OR EGR VALVE SOLENOID CIRCUIT OPEN. CODE 33 - MAP SENSOR.CODE 34 - VACUUM SENSOR OR MAP SENSOR.CODE 35 - IDLE SPEED CONTROL. CODE 41 - EST CIRCUIT. CODE 42 - ELECTRONIC SPARK TIMING.CODE 43 - ELECTRONIC SPARK CONTROL UNIT. CODE 44 - LEAN EXHAUST.CODE 45 - RICH EXHAUST. CODE 51 - PROM OR MEM CAL.CODE 52 - CALPAK. CODE 53 -EGR VALVE CARBURETED ENGINE THE EGR VALVE VACUUM SENSOR HAS RECEIVED IMPROPER EGR VACUUM. CODE 54 - M C SOLENOID CARBURETED ENGINE MIXTURE CONTROL SOLENOID SHORTED OR FAULTY ECM.CODE 54- FUEL INJECTED ENGINE FUEL PUMP VOLTAGE IS LOW.CODE 55 - ECM MAKE SURE PCM GROUND CONNECTIONS ARE TIGHT.IF OKAY.REPLACE THE ECM.

Mar 27, 2010 | 1987 Pontiac Fiero

2 Answers

1994 Yukon running rich and flooding


Fuel pump circuit (low voltage)
Try replacing the fuel pump relay or testing it if you have the manual.

Sep 20, 2009 | 1994 GMC Yukon

Not finding what you are looking for?
1993 Chevrolet S-10 Logo

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...