Question about 2004 GMC Envoy

1 Answer

2005 GMC Envoy passanger headlight

The passanger headlight went out and we put a new bulb in and it still will not come on. Is there anything else I need to do with it?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 324 Answers

First, did you touch the bulb with your fingers when you put it in? if so it is likely you blew the bulb, you can not touch the glass of the bulb.

If that is not the problem, make sure the wiring going to the socket is not cracked corroded or pulled out.

Posted on Nov 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change 04 envoy bulb


Headlight Replacement (Envoy)

Lift hood, at top of each headlight assembly look for two L-shaped tabs. Pull these tabs straight up, this will release the headlight assembly. Lift assembly forward to gain access to rear of assembly. There two rubber caps, the top one is for access to the low beam and the bottom for the high beam bulbs. Remove the appropriate cap, grasp bulb socket and turn CCW to release. Unplug bulb from socket by releasing catch on side of socket, install new bulb, DO NOT touch bulb glass with fingers. Reverse steps to re-assemble.

Jun 18, 2012 | 2004 GMC Envoy

1 Answer

Need to replace low beam bulbs in 2004 GMC envoy. Help?


Lift hood, at top of each headlight assembly look for two L-shaped tabs. Pull these tabs straight up, this will release the headlight assembly. Lift assembly forward to gain access to rear of assembly. There two rubber caps, the top one is for access to the low beam and the bottom for the high beam bulbs. Remove the appropriate cap, grasp bulb socket and turn CCW to release. Unplug bulb from socket by releasing catch on side of socket, install new bulb, DO NOT touch bulb glass with fingers. Reverse steps to re-assemble.

Aug 26, 2010 | 2004 GMC Envoy

1 Answer

BOTH HEADLIGHTS WENT OUT IN MY GMC ENVOY 2005


If it is just the low beams that are out, replace relay #46 in the under hood fuse panel.

Aug 26, 2010 | 2005 GMC Envoy

1 Answer

Replacing the low beam headlight on a 2004 gmc envoy


Just above the headlight assembly are two angled tabs, pull these straight up (they may need some effort). These will release the assembly, carefully pull the entire assembly forward. Access to the headlight bulb is behind the two rubber caps, the upper cap is for the low beam. Remove this cap, twist the headlight bulb socket CCW and remove. Disconnect bulb from harness by prying up gently on locking tab on socket, and pull bulb out. Being careful not to touch the new bulb glass surface with your finger, plug it into the socket and install it back into the headlight assembly turning it CW. Reinstall rubber cap, seat headlight assembly on frame, lining up the bottom and top pegs. Once the assembly is fully seated, push the two angled tabs down, locking the assembly in place.

Oct 15, 2009 | 2004 GMC Envoy

1 Answer

Both low beam headlights on my 05 GMC Envoy do not work. I have replaced the bulbs but something else is wrong. any suggestions


Check your headlamp relays under the hood, should be located on either the L/H or R/H fender well , could be inside a black plastic box labled fuses and relays... there will be a label on the underside of the lid to this box locate the relays as per lables... please rate my help thanks...

Aug 06, 2009 | 2005 GMC Envoy Xl

1 Answer

How to change low beams on gmc 2005 envoy


Open hood, look for two L-shaped tabs on top of the headlight assemblies, pull these straight up. This will release the assembly. lift assembly out as far as wiring harness will allow, look for a circular rubber cap on the rear side of the assembly, the top cap is for the low beam, remove cap and turn bulb socket CCW to release socket. Unplug old bulb and install new, DO NOT touch bulb glass. Re-assemble in reverse order.

Jun 20, 2009 | 2005 GMC Envoy Xl

2 Answers

2005 GMC Envoy passanger headlight


I have had the same problem on both Headlights at different times on my 2002 Envoy. I had to replace bulb sockets. Sockets with pigtail can be purchased at most auto parts stores. Make sure to put conductive lube on terminals when reinstalling.

Nov 22, 2008 | 2005 GMC Envoy

2 Answers

How to replace the headlights on my 2003 GMC envoy.


The headlights on the envoy are the easiest parts of the car to repair. You just pull the two tabs at the top of the headlights, screw out the bulb containers and you are good to go

Nov 01, 2008 | 2003 GMC Envoy

1 Answer

Replace headlight


It is quick and extremely easy to replace the headlights on the envoys. Look at the top of the headlight assembly. you will see a kinda large lever you can pull up. Pull it up and the entire headlight assembly will be released from the car. Be prepared to hold it, and whatever you do, do not touch the new bulb with your bear hands!!. Kinda self explanitary once you get the bracket loose by pulling up the lever. Replace the bulb, and put the assembly back in the same way,, and press back down on the lever. Your done,, takes about 2 to 3 minutes.

Jul 18, 2008 | 2002 GMC Envoy

Not finding what you are looking for?
2004 GMC Envoy Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...