Question about 2008 Dodge Charger

2 Answers

Grill removal I want to remove the grill so I can install grill lights and a siren speaker

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

There are 4 screws holding the grill into the front fascia on the Charger. The easier 2 are right in the center as you look behind the grill and you can get them out with a regular phillips head screwdriver. The other 2 are on both ends of the horizontal bar in the center of the grill. those are harder to get out but can be done with the right tools. I used a ratcheting wrench with a phillips bit on the end to remove them. After you take out the 4 screws, the grill will pop right out. For more info on Chargers, check out www.Chargerforumz.com, tell them liljoejoe54 sent ya!

Posted on Dec 18, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 185 Answers

Ok owhats the problem look under the hood and ull see 3 to 5 screws there take them out and ur done

Posted on Nov 22, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install a grill for a 2001 volkswagon beetle


TO REMOVE GRILLE FROM BEHIND THE BUMPER COVER RELEASE PLASTIC CLIPS AND DETACH THE GRILLE. IF YOU HAVE FOG LIGHTS DISCONNECT THE ELECTRICAL CONNECTORS FROM THE FOG LIGHTS AND REMOVE THE FOG LAMP MOUNTING SCREWS BEFORE DETACHING THE GRILLE.WHEN YOU INSTALL GRILLE PLACE GRILLE IN POSITION AND SEAT THE CLIPS INTO HOLES IN THE BUMPER COVER. IF YOU HAVE FOG LAMPS INSTALL GRILLE IN POSITION THE INSTALL FOG LAMPS MOUNTING SCREWS BACK IN PLACE TO HOLD GRILLE IN POSITION.

Sep 25, 2011 | Volkswagen New Beetle Cars & Trucks

1 Answer

Need instructions to replace the passenger side mirror and the driver side tail light on a 1999 Ford Taurus 4-door sedan. Thank you, Gary S.


Section 01-09: Mirrors, Rear View 1999 Taurus/Sable Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/25/1998 Mirror, Power-Outside Rear View Removal
  1. Disconnect battery ground cable (14301).
  1. Remove front door trim panel (23942). Refer to Section 01-05.
  1. Remove radio speaker grille from cover assembly by squeezing or pinching between thumb and index finger.
  1. Remove two screws from cover assembly.
  1. Disconnect outside rearview mirror wiring connector (C515-LH; C615-RH). Remove wiring guides as necessary.
  1. Remove three outside rear view mirror retaining nuts. Remove outside rear view mirror (17682) while guiding wiring and connector through hole in door.


an0786b.gif


Item Part Number Description 1 17682 Outside Rear View Mirror 2 N621906-S36 Nut (3 Req'd) 3 F8DB-17D699-
AAW Cover Assembly Rear Substrate-LH 3 F8DB-17D698-
AAW Cover Assembly Rear Substrate-RH 4 N808968 Screw 5 F8DB-18B984-
AAW Speaker Grille-Standard (No Badge)-LH 5 F8DB-18985-
AAW Speaker Grille-Standard (No Badge)-RH 5 F8DB-18K901-
BAW Speaker Grille-Mach-LH 5 F8DB-18978-
BAW Speaker Grille-Mach-RH 5 F8DB-238A35-
AAW Speaker Grille-Blank (No Speaker)-LH 5 F8DB-238A34-
AAW Speaker Grille-Blank (No Speaker)-RH A - Tighten to 6-8 Nm (54-70 lb-in) ------------------
Trim Panel, Door Front
Removal
  1. Remove cover behind inside door handle.
  1. Remove screw from bottom of pull cup retaining front door trim panel to front door (20124).
  1. Remove three screws retaining front door trim panel to front door.
  1. NOTE: Do not attempt to remove more than one pushpin at a time.

    Using Rotunda Windshield and Molding Trim Removal Kit 107-R0401 or equivalent, remove the door trim panel by pulling one door trim panel pushpin at a time from the inner door skin.
  1. Disconnect electrical connectors as necessary. Refer to Section 01-14A.
Installation
  1. Follow removal procedure in reverse order.
  1. Replace all pushpins with new pushpins (N808994-S).
Front Door Trim Panel


ar0318d.gif

Jan 14, 2011 | 1999 Ford Taurus

1 Answer

How do i car door panels safely


  1. Remove the cover behind the inside door handle.
  2. Remove the screw from the bottom of the pull cup retaining the front door trim panel to the front door.
  3. Remove the two screws retaining the sail panel/speaker grille assembly and remove the panel/grille from the door.
  4. Remove the three screws retaining the front door trim panel to the front door.

Do not attempt to remove more than one pushpin at a time.

  1. Use a suitable tool to remove the pushpins from the door.
  2. Carefully lift the door panel away from the door.
  3. Detach the electrical connectors as necessary and remove the panel from the door.

To install:

  1. Installation is the reverse of removal.
Door Panel

This procedure applies to both the front and rear door panels.


// // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 30; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]> var _strTreeScrollHidName = 'ctl00_hidTreeScrollPos'; c17hydro_23.gif

Remove the cover from behind the inside door handle by gently pulling it out to release the retaining tabs


c17hydro_24.gif

Remove the pull cup retaining screw cover and...



c17hydro_25.gif

... remove the retaining screw from the cup and lift the cup straight up out of the door panel



c17hydro_26.gif

Remove the two sail panel/speaker grille retaining screws and...



c17hydro_27.gif

... remove the panel/grille from the door



c17hydro_28.gif

The door panel is retained to the door by 11 retaining clips



c17hydro_29.gif

Carefully lift the door panel off of the door and...



c17hydro_30.gif

... detach the electrical connectors from the switches and remove the panel from the vehicle

Nov 13, 2010 | 1996 Ford Taurus

1 Answer

How to replace rear speaker grills on 2004 Toyota Camry


Remove the rear seat, pull up and out on the bottom half, remove the sides of the back- one bolt on bottom of each side,remove the backrest, then remove the whole deck lid with speaker grills in it , then you can replace the speaker grills.

Mar 17, 2010 | 2004 Toyota Camry

1 Answer

How do you remove the inside paneling to fix a broken door handle?


4-Cylinder Engines
  1. Remove the screw in the door handle trim, slide the handle assembly forward, and out to access the lock rod clip. Release the clip, disconnect the door lock switch and remove the door opener handle assembly.
  2. Carefully pry off the cap(s) in the armrest pocket, then remove the screw(s).
  3. Carefully pry off the cap under the armrest and remove the screw.
  4. Using a suitable trim panel removal tool, unsnap the door panel from the door frame.
  5. Unplug the electrical connectors for the power windows, power mirror and courtesy light.
  6. Carefully lift the door panel up and away from the door frame.
  7. Installation is the reverse of the removal procedure.

V6 Engine
  1. Remove the screw in the door handle trim, slide the handle assembly forward, and out to access the lock rod clip. Release the clip, disconnect the door lock switch and remove the door opener handle assembly.
  2. Carefully unsnap the rear of the speaker grill, lift and pull back to release it and remove the grille.
  3. Remove the panel mounting screws located around the perimeter of the speaker.
  4. Remove the cap and screw in the pull pocket of the armrest.
  5. Slide the pocket back slightly to release the front hook, then lift up, detach the electrical connectors and remove the pocket assembly.
  6. Using a suitable trim panel removal tool, unsnap the door panel from the door frame.
  7. Carefully lift the door panel up and away from the door frame slightly and disconnect the speaker connector.
  8. Installation is the reverse of the removal procedure.

Oct 13, 2009 | 1999 Honda Odyssey

1 Answer

Need to remove the dashboard bezel and instrument cluster from 1990 Buick Regal . What are the details?


Regal 1988–94 MODELS
  1. Disconnect the negative battery cable.
  2. Remove the instrument panel pad:
  3. Carefully pry the speaker grilles and disconnect the Daytime Running Lamp sensor if equipped.
  4. Remove the screw under each speaker grille.
  5. Remove the screws at the lower edge of the instrument panel pad.
  6. Remove the pad by lifting the front and pulling toward you to release it.
  7. Remove the speakers
  8. Remove the instrument cluster.
  9. Remove the glovebox.
  10. Remove the right side sound insulator.
  11. Remove the climate control system switch panel and sound system controls.
  12. Remove the English/Metric switch.
  13. Remove the lights switches.
  14. Remove the cassette deck or compartment that replaces it if not equipped. Remove the ashtray and bracket.
  15. Remove the ALDL connector and allow it to dangle below the instrument panel.
  16. Remove the parking brake release handle and allow it to dangle below.
  17. Remove the remote radio receiver.
  18. Remove the steering column trim plate and lower the steering column.
  19. Remove 7 bolts holding the carrier (5 at the top and 2 at the bottom). Remove the 2 bolts above the steering column.
  20. Remove the 5 screws holding the main air duct.
  21. Remove the 3 nuts holding the conduit. Two are above the glovebox and the other is through the cassette/compartment opening.
  22. Disengage 9 clips holding the wiring harness.
  23. Have a helper assist you, and remove the instrument panel assembly from the vehicle. To install:
  24. Carefully install the instrument panel to the vehicle. Be sure to clear all wiring, etc.
  25. Engage the clips holding the wiring harness.
  26. Install the 3 nuts holding the conduit.
  27. Install the screws holding the main air duct.
  28. Install the bolts holding the carrier.
  29. Secure the steering column and install the trim plate.
  30. Install the remaining components in the reverse of the removal procedure.
  31. Connect the negative battery cable and check all items in the instrument panel for proper operation.

Jul 23, 2009 | 1990 Buick Regal

2 Answers

How do I remove and replace the rear speaker in my 2002 Lexus ES 300?


Hello, I have a 2000 ES300 and while the body style is different believe the newer model still has the rear deck mounted sub-woofer that you are referring to. The process of removing this speaker would start off the same as if you were going to replace the third brake light also located in this housing. Using a flathead screwdriver work your way around prying/popping up all four corners of the speaker grill covering the speaker that have the retainer clips. Once you disengage the clips work/maneuver the grill up and towards you gently and it should slide out. The bulb for the third brae light will be attached to this speaker grill, disconnect the snap wire from the bulb and you should have a clear visual of the speaker and the four bolthead screws securing it. Remove these screws and your almost home free. The next part might be slightly more difficult. If the speaker s simply connected by a clipped on wiring harness, just detach.On my 2000 ES300 i have the pioneer system(Not Nakimichi) and the 2 wires (one black, and one red) are soldered directly to the speaker. You can take a soldering iron(maybe a battery or gas powered one unless you have an inverter) and remelt the solder to remove the wires or you can elect to simply cut the wires. If you choose to cut them make sure you cut them as close as possible to the soldered joints so you have plenty of wire left to install the replacement speaker.Then install replacement either soldering or using crimp clamps and reassemble. ( Note if you simply want to add a aftermarket amplified sub-woofer you don't need to remove the sub-woofer out of the housing. You can tap into the wire leads and run it directly to the amplifier. Just cut one of the wires leading to the stock sub-woofer so it doesn't also come on and potentially blow while the radio is on. This will also prevent any bass humming when the radio is shut off but the aftermarket amplifier is still on because once one of the wires to the stock sub-woofer is disconnected or cut it breaks the circuit. Hope this helps.

Jun 13, 2009 | 2000 Lexus ES 300

1 Answer

Install Rear Speakers Ford F150 1997 Regular Cab


you should not have to remove the panel by taking the four phillips screws out of the speaker grill you will pull out through front

Jan 13, 2009 | 1997 Ford F150 Regular Cab

2 Answers

Removing front and back speakers in 1991 Grand Am....


There is a lot involved in replacing these speakers. You should also know that the original factory speakers are 10 ohm speakers. This means that if you replace them with new speakers (most of which are 4 ohm) you run the risk of damaging the stereo, the speakers, or both. This can also cause a potential fire hazard in your car. If you want new speakers, you really should look at installing a new stereo as well.

To get to the back speakers, you will need to remove 2 bolts located under the front edge of the rear seat (bottom). After you remove the bottom, you will need to remove the rear seat (back). This involves removing the bolts that hold down the rear seat belts, which is a large sized torx bit (T-45, T-47, or T-50... Don't remember which). After removing these, lift straight up on the seat back to remove. Now remove the deck brake light housing, and the bracket that holds it. Now the deck cover can be removed. Be careful not to bend it too much getting it out from under the side trim on both sides.

For the front speakers, you must disassemble a good portion of the dash. Remove the screw holding the light switch and the wiper switch housings. This screw is underneath each housing. Once removed, there are dash mounting screws behind them. These screws (and many of the other dash screws) are a smaller torx-bit (T-10 or T-15, don't remember which). Sometimes they use a 7mm bolt. There is a cover panel just above the glove box. This panel is held on with 2 screws located in the glove box. After removing this panel, you will find 2 or 3 bolts holding on the dash. Last but not least, you will find 2 bolts inside each of the defroster vent grilles. These grilles just snap out for easier access to the bolts.

1991 Pontiac Grand Am Car Radio Stereo Audio Wiring Diagram
Car Radio Battery Constant 12v+ Wire: Orange
Car Radio Accessory Switched 12v+ Wire: Yellow
Car Radio Ground Wire: Black
Car Radio Illumination Wire: Gray
Car Stereo Dimmer Wire: Brown
Car Stereo Antenna Trigger: Pink
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: 4" Round
Car Audio Front Speakers Location: In Dash
Left Front Speaker Positive Wire (+): Tan
Left Front Speaker Negative Wire (-): Gray
Right Front Speaker Positive Wire (+): Light Green
Right Front Speaker Negative Wire (-): Dark Green
Car Audio Rear Speakers Size: 6" x 9" Oval
Car Audio Rear Speakers Location: Rear Deck
Left Rear Speaker Positive Wire (+): Brown
Left Rear Speaker Negative Wire (-): Yellow
Right Rear Speaker Positive Wire (+): Dark Blue
Right Rear Speaker Negative Wire (-): Light Blue

Nov 30, 2008 | 1991 Pontiac Grand Am

2 Answers

Dash


REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Remove the ashtray.
  3. Unfasten the accessory trim plate screws, then remove the accessory trim plate.
  4. Remove the glove box door strap, then remove the glove box hinge screws.
  5. Remove the glove box door frame.
  6. Loosen the ashtray support screws, then remove the ashtray support.
  7. Remove the glove box.
  8. Unfasten the radio bracket bushing nut, then remove the radio.
  9. Disconnect the speaker grille screws, then remove the speaker grilles.
  10. Loosen the speaker retainers, then remove the front radio speakers.
  11. Unfasten the sound insulation panel screws, then remove the sound insulation panels.
  12. Loosen the steering column filler screws, then remove the steering column filler.
  13. Disconnect the hood release cable.
  14. Disconnect the shift indicator cable from the column bowl.
  15. Disconnect the steering column support nuts, then lower the steering column. For details regarding this procedure, please refer to of this guide.
  16. Unfasten the switch plate trim screw, then remove the switch trim plate.
  17. Disengage the electrical wiring harness from the rear defogger and the light switches.
  18. Disconnect the heater and A/C control.
  19. Disconnect the cluster housing bezel mounting nuts, then remove the bezel.
  20. Remove the instrument cluster from the vehicle. Disconnect and allow to hang:
  21. The speedometer instrument panel electrical connector and the Vehicle Speed Sensor connector
  22. The courtesy lamps and the cruise control module
  23. The horn relay, multi-function alarm and the flasher assembly
  24. If necessary, remove the applicable computer control module.
  25. Remove the instrument panel-to-cowl mounts:
    1. Unfasten the screws from under the panel.
    2. Remove the instrument panel support.
    3. Unfasten the screws in the defroster outlets.
    4. Remove the ductwork, dash plugs, wire looms, and heater cables attached to the panel.
  26. Disengage any electrical connections/wires routed through the instrument panel, then remove the instrument panel from the vehicle.
To install:
  1. Install the instrument panel assembly to the cowl, carefully routing and connecting the electrical wires and cables.
  2. Connect the instrument panel-to-cowl mounts:
    1. Connect the ductwork, dash plugs, wire looms, and heater cables to the instrument panel.
    2. Secure the screws in the defroster outlets.
    3. Install the instrument panel support, then fasten the screws (located under the panel).
  3. Install the computer control module, if removed.
  4. Install the instrument cluster. Reconnect and mount:
  5. The speedometer and Vehicle Speed Sensor electrical connectors
  6. The flasher assembly, multi-function alarm, and horn relay
  7. The cruise control module and the courtesy lamps
  8. Install the cluster housing bezel using the mounting nuts. Tighten the nuts to 12 inch lbs. (1.4 Nm).
  9. Install the heater and A/C control.
  10. Engage the rear defogger and light switch electrical harness.
  11. Install the switch trim plate using the retaining screw. Tighten the screw to 12 inch lbs. (1.4 Nm).
  12. Raise the steering column to the mounting bracket, then install the steering column support nuts.
  13. Install the shift indicator column to the column bowl, making sure that the indicator is aligned.
  14. Connect the hood release cable.
  15. Install the steering column filler panel using the retaining screws. Tighten the screws to 14 inch lbs. (1.6 Nm).
  16. Install the sound insulation panels using the retaining screws. Tighten the screws to 14 inch lbs. (1.6 Nm).
  17. Install the front radio speakers and speaker retainers, then connect the speaker grilles using the retaining screws. Tighten the screws to 12 inch lbs. (1.4 Nm).
  18. Install the radio and tighten the fastener to 12 inch lbs. (1.4 Nm).
  19. Install the glove compartment, then install the ashtray support using the retaining screws. Tighten the screws to 12 inch lbs. (1.4 Nm).
  20. Install the glove compartment door frame, door and door hinge screws. Tighten the screws to 12 inch lbs. (1.4 Nm).
  21. Install the glove compartment door strap.
  22. Install the accessory trim plate using the retaining screws. Tighten the screws to 12 inch lbs. (1.4 Nm).
  23. Install the ashtray, then connect the negative battery cable.

Oct 02, 2008 | 1989 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...