Question about 1998 Mitsubishi Galant
Hey I have a 96 camaro rs that has a miss under load I have replaced the IAC Valve and throttle relay with no luck. Locals say I probably need a new coil pack because a friend took a powerwasher under the hood. It starts up and runs at high rpm but then slows down to idle when it warms up a bit.
Yes coil or the power washer blew a vacuum line apart..check for vacuum leaks good luck
Posted on Nov 22, 2008
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Jun 25, 2014 | Cars & Trucks
Feb 12, 2013 | 1990 Chevrolet Camaro
Aug 18, 2012 | 1996 Chevrolet Camaro
Apr 05, 2011 | 1996 Chevrolet Camaro
The Idle Air Control (IAC) is a bi-directional motor driven by two coils. The purpose of the IAC valve is to control engine idle speed, while preventing stalls due to changes in the engine load. The IAC valve, mounted in the throttle body, controls bypass air around the throttle plate. The PCM controls engine idle speed by adjusting the position of the IAC motor pintle. The PCM pulses current to the IAC coils in small steps (counts) to extend the pintle into a passage in the throttle body to decrease air flow. The PCM reverses the current pulses to retract the pintle, increasing air flow. This method allows highly accurate control of idle speed and quick response to changes in engine load. If RPM is too low, the PCM will retract the IAC pintle, resulting in more air being bypassed around the throttle plate to increase RPM. If the RPM is too high, the PCM will extend the IAC pintle, allowing less air to be bypassed around the throttle plate, decreasing RPM.
Fig. Typical Idle Air Control (IAC) valve components
During idle, the proper position of the of the IAC pintle is calculated by the PCM based on the battery voltage, coolant temperature, engine load and engine RPM. If the RPM drops below a specified value, and the throttle plate is closed (TP sensor voltage is between 0.20-0.74), the PCM senses a near stall condition. The PCM will then calculate a new IAC pintle position to prevent stalls.
If the IAC valve is disconnected and reconnected with the engine running, the idle RPM will be wrong. In this case, the IAC has to be reset. The IAC resets when the ignition switch is cycled ON and then OFF . When servicing the IAC, it should be disconnected or connected with the ignition switch OFF in order to keep from having to reset the IAC valve.
The position of the IAC pintle affects engine start up and the idle characteristics of the vehicle. If the IAC pintle is fully open, too much air will be allowed into the manifold. This results in high idle speed, along with possible hard starting and a lean air/fuel ratio. A Diagnostic Trouble Code (DTC) may set. If the IAC pintle is stuck closed, too little air will be allowed in the manifold. This results in a low idle speed, along with hard starting and a rich air/fuel ratio. Again, a Diagnostic Trouble Code (DTC) may set. If the IAC pintle is stuck part way open, the idle may be high or low and will not respond to changes in engine load.
As with most all engine control sensors used in your vehicle, a thorough and proper test can only be performed by a qualified technician using a scan tool to read the data stream from the PCM. There are a few items a non-professional should check before taking the vehicle to a qualified technician for diagnosis and repair.
Check for a poor connection at the PCM or IAC motor. Inspect the harness connectors for backed out terminals, improper mating, broken locks, improperly formed or damaged terminals and poor terminal-to-wire connection. Inspect for a damaged wiring harness, especially if heavy work has recently been performed (intake manifold removal, engine removal, etc.) where the throttle body has been disturbed. Inspect for a restricted air intake system. Check for a possible collapsed air intake duct, restricted air filter element or foreign objects blocking the air intake system. Inspect the throttle body. Check for objects blocking the IAC passage or throttle bore. Excessive deposits, especially on high-mileage engines, can build up in the IAC passage and on the IAC pintle. Excessive deposits can also build up on the throttle plate, so check for a sticking throttle plate. Check for vacuum leaks such as disconnected hoses, leaks at the EGR valve and EGR pipe to the intake manifold, leaks at the throttle body, faulty or incorrectly installed PCV valve, leaks at the intake manifold brake booster hose connection, etc.
REMOVAL & INSTALLATION
Fig. The Idle Air Control (IAC) valve is mounted on the throttle body-3.8L (VIN K) engine shown, others similar
NOTE Before installing a new IAC valve, measure the distance that the valve is extended. The measurement should be made from the motor housing to the end of the valve cone (pintle). The distance should be no greater than 1 1 / 8 inch (28mm). If the pintle is extended too far, adjustment is required, otherwise damage may occur when the IAC valve is installed. Adjust the IAC valve by compressing the pintle to achieve the correct length.
Oct 13, 2010 | 2000 Pontiac Grand Prix
Oct 01, 2010 | 1992 Chevrolet Camaro
Sep 30, 2009 | 1996 Jeep Grand Cherokee
Aug 30, 2009 | 1996 Jeep Grand Cherokee
Feb 12, 2017 | 1998 Mitsubishi Galant
215 people viewed this question
Usually answered in minutes!