Question about 2001 Dodge Stratus

2 Answers

2001 dodge stratus r/t

Would the intake valve have anything to do with the transmision?

Posted by on


2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

760 and 765 c and d codes 2001 dodge stratus R/T 3.0 engine.. Trans quit working as we were driving down the freeway. The trans fluid is clean, not burnt at all....

Posted on Aug 24, 2009

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 123 Answers

What brings on this question might I ask? Low engine out put from the unlikely stuck or burnt valve could upset the transmisson shift points. TPS signal is based on a pre mapped torque curve. If the power isn't there then yes the transmisson could have issues. What makes you feel there is a problem with the intake valve? And also is this the 2.7L engine?

Posted on Nov 22, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How hard are head gaskets to change on a 2001 dodge stratus, and what problems come with it? thanks

There you go

May 20, 2012 | 2001 Dodge Stratus

1 Answer

Where are to spark plugs on a 2001 dodge stratus engine

What size engine? 4cyl or 6cyl?

If you have the 6cly, the spark plus are in the valve covers like an old hemi engine, the front three are no problem, but you have to remove the intake manifold to get the back three :-(

Hope this helps.

Jan 23, 2011 | 2001 Dodge Stratus

3 Answers

Where is the map sensor located for a 2005 dodge stratus sxt 2.7?

it is always located on the air intake were you put the air filter.remove all the hoseing were the air filter is located ok and you will see it ,It looks like a niddle

Aug 24, 2010 | 2005 Dodge Stratus

1 Answer

Locating an egr vavle on a 2005 dodge stratus

In my 2001 Dodge Stratus ES sedan (2.7L V6), the EGR has shiny piping that runs into the side of the black plastic intake manifold on top of the engine. The other end runs down beside the engine heads and routes into the rear exhaust manifold.

Hope this helps. Best of luck. 

Aug 10, 2010 | 2006 Dodge Stratus

1 Answer

2001 Stratus: where is the egr valve loated on my stratus 2001 3...

should be on the intake manifold should be a dish looking shaped part... go online and pul;l a pic of one up on a parts page to help identify... also check with Auto Zone parts house as they will give you a print out of its exact location and the part if they have it in stock.

May 06, 2010 | 2001 Dodge Stratus

1 Answer

Do I need a secondary timing chain or primary for a 2004 Dodge Stratus 6-cyl 2.7?

if you have dohc the 2.7 has 3 timing chains The primary chain goes around the crank sprocket the the water pump and around two intake cam sprockets. The other two chains run around seperate intake and exhaust cam sprockets, to synchronize the intake and exhaust valve timing.

Apr 13, 2010 | 2004 Dodge Stratus

1 Answer

How do you reach the spark plug in the back of the engine of a 2001 dodge stratus 2.7 v6?

the plastic intake plenum must be removed or at least loosened so you can access plugs.

Mar 29, 2009 | 2001 Dodge Stratus

2 Answers

Changing valve cover gasket on 2001 dodge stratus, how

remove all the components in the way of the valve cover.  Then remove the valve cover and replace the gasket and reassemble.
usually about a 3 to 4 hour job.

Mar 16, 2009 | 2004 Dodge Stratus

Not finding what you are looking for?
2001 Dodge Stratus Logo

Related Topics:

264 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides