Question about 2001 Chevrolet Silverado 3500

1 Answer

Turn signals wont work,4 ways only work one side(left) untill tou turn right directional on all fuses good 4 truck and trallier can power directional manualy by jumping power to it but not through switch

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I bought a 96 jeep cherokee took the alarm out cause it didnt work i thought.now the turn signals wont work.

Posted on Aug 29, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My right turn signal is not working i changed the bulbs and checked the fuse why is it not still working


What is year--make--model?
Neither the front or rear right turn work? If that is correct, I'd check the turn signal switch and wiring circuit.

Mar 16, 2016 | Cars & Trucks

1 Answer

How can I repair a malfunctioning left front signal light?


The flasher unit for the four ways is separate from the turn signal.
If the rear light is flashing fast means the front light is malfunctioning. Check all wiring from the dash to the light itself. I had one a wire was pinched and had broken

Jul 19, 2015 | Cars & Trucks

1 Answer

1987 ford ranger turn signals keep blowing fuses. have changed flasher fuse and switch on column. just keeps blowing?


first thing i guess to understand what is going on here ,is a little back to basics on how turnsignals work , first item you have is power fuse then it's off to flasher module than it goes to the turnsignal switch on colum ,of course anywhere on it way to there the power could got to ground and cause the fuse to trip, now the power depending on Left or right selection , is directed to lights on both front and back of truck,thankfully rangers don't have em on the side) now any place in this pathway the wire could go to ground and blow the fuse, now to troubleshoot and narrow down the area that fault is located , (1) replace fuse with correct size and ck for proper fit in fusebox and start and operate truck for a few minutes DO not use turnsignals, ck fuse is it still good if so go to step 2 if not stop and ck wire conditions in steering colum and switch(2) start truck and try right hand turn signal only verify lights working ,Ok yes/no if not replace fuse and try left side same way, Ok yes /no if right or left side only blows fuses take ALL bulbS OUT of lights and try again , if fuse still blows then look for wire fault on that side of truck if fuse is still good then look carefull at light bulb sockets for rust and powered corrosion (ill bet an 87 has some ) you may need to replace bulb sockets , they do sell em in autoparts stores .

Jun 30, 2014 | 1987 Ford Ranger

1 Answer

Turn signals went out


replace the fuses first. for turn/hazards.
the HAZ fuse 10 amps ., do hazards fail?????????


old car, very old. 1980 corolla.
first off, the lamps are brass based lamps. 115x lamps
they can short so replace them all or remove all of them
and put only 1 new lamp in (of the 4) if this works, good.
if not use a voltmeter to find the cause.
12v during a flash is good, 0v dead, 6v is shorted wires.
this is easy, dont panic, get the schematic for the car is best way.
The FSM has this but are rare for such and old car.

i looked online , alldata.com
and the schematic is there.
the path is from battery to ground as follows
10a haz fuse and 5am turn fuse. (2 fuse!)
the fuses drives the HAZ module
the HAZ module drives the lamps directly in HAZ mode
in blink mode the HAZ module drives the combo turn switch.
a bad flasher module KILL BOTH, (did it?)
the comb drives left or right side and the lamps are all grounded
completing the path of electrics, and the lamps glow.
current flows, and the lamps glow.

lamps
green-black is left
green-yell is left side.

the best test for this car, is to cycle the HAZ button over and over
until they work, most switches this old. 33 years are dirty and fail.
so cycle it. 10 times, if the HAZ fails.
it must work on HAZ or its all a wasted effort.
because the HAZ module feeds the binkers...




Jan 20, 2014 | 1980 Toyota Corolla

1 Answer

97 cad turn signal lift side and brake not working **** right is working


The problem could be in one fuse, bad ligth bulb, bad combination switch wich is the turn signal lever siwtch, or the combination of all this. Is the front left turn signal working, in order to find out if the turn signal switch is working check for power at the the cable in the corredpondent connector that way you eliminate the posibilty of the turn signal sitch if you have power at the connector also do the same at the stop ligth if there is no power you have problaby bad fuse, hope this help tou out.

May 13, 2012 | Cars & Trucks

1 Answer

Iv got an 88 F150 4x4 iv got turn signals light fuse is good got power at break switch need no break lights and is there suppost 2 b 1 r 2 wires coming out of fuse box


Do you have power at both sides of the brake switch when the brake is applied? If so it sounds like the turn signal switch is bad. try turning on and off the 4 ways a few times. sometimes this will clean the connections and it will start working.
The power goes through the fuse to the brake switch. from the brake switch to the turn signal switch from the turn signal switch to the tail lights. If the 4 ways are on the power goes through the 4 way fuse to the 4 way flashers then to both sides.
If the turn signal is on and the brake is on, the turn switch cansles the power from the brake and uses power from a 3 fuse and flasher for the side that the turn signal is called for.
If I typed to fast let me know. I can answer any questions you might have.
If this helped you please vote 4 thumbs up. :-)
good Luck and God Bless

Jun 07, 2011 | 1988 Ford F 150

2 Answers

On my 98 jeep cherokee when connecting the tailgate replace kit I accidentally touch the yellow left turn wire, with the brown tail light wire. As result my left side on the 4 way exterior dim lights no...


If it happened the way you described it. I don't see how it could possibly have damaged anything. I guess what you are saying is that the left tail lights are not working? ("4 way exterior dim lights"???) Touching the tail light wire to the turn signal wire will only cause your turn signals to light up. (I am assuming that the tail light switch was on at the time)
I think it is more likely that the brown wire touched ground. This would make a bright flash, blow a fuse and cause the symptom you are describing...I think you need to check the fuse again.
There are separate fuses for the left and right sides. The left side tail lamp fuse is fuse #7 in the junction block it is a 10 Amp fuse. The junction block is located on the right cowl side inner panel - We are NOT talking about the Power Distribution Center under the hood.

All of the above is also assuming that we are talking about a plain Cherokee, Cherokee SE, Cherokee classic or Cherokee Limited.

If we are talking about any of the Grand Cherokees, you may have a fried lamp outage module.

Apr 08, 2011 | 1998 Jeep Cherokee

1 Answer

95 olds cutlass supreme both blinkers do not work. Emergency flashers do work. Looks like fuses are good


There may be separate flashers for the Emergency 4 ways vs. the turn signals left or right. Try to replace the flasher for the turn signals located under the dash on the driver's side. That's the way my 1990 Cadillac was, and it may be the case for you.

Feb 09, 2011 | 1988 Oldsmobile Cutlass

1 Answer

After a rear end collision, the turn signals and 4-way flashers don't work right. turn on left signal and all lights in rear flash.


Sounds like a ground problem, and the turn signal is trying to use another path to ground, causing the other lights to glow.

Check the left side bulb socket for a good ground.

The other test is to pull the L & R Stop / Turn fuses for the trailer tow adapter, to make sure the problem is not with the 4 or 7 pin trailer adapters.

May 04, 2010 | 2006 Ford F-150

2 Answers

Directional signals screwed up, but my 4 way flashers work.


For this modle and year the turn signal flasher should be mounted in a clip on the right side of the steering column support bracket. The hazard flasher is located under the instrument panel in the module block, on the right side.
Hope this helps,
Regards,

Feb 13, 2009 | 1995 Buick Regal

Not finding what you are looking for?
Cars & Trucks Logo

247 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...