Question about 2005 Chevrolet Equinox

1 Answer

Where is the battery - 2005 Chevrolet Equinox

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 102 Answers

The battery for this vehicle is-
From under the hood, on the rt. side (dr. side) there is a black plastic cover, under that is a computer module, the battery is under the next black plastic cover. - Tech jk

Posted on Dec 06, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

Tip

How to Wire On-Board Marine Battery Chargers


Battery chargers are wired into a boat's electrical system. Wiring the charger to a battery switch permits the charging of the individual batteries or battery banks. The switch can be configured to charge both batteries or battery banks at once. Mounting the charger in the vessel keeps the charger where it will do the most good--connected to the batteries. This is useful if you are stuck with low batteries and need a recharge. Power from a generator, shore power or even AC power from another vessel can be used to get you going again

Instructions Things You'll Need:
Battery charger
Battery switch
Battery cable (sized)
Cable cutters
Razor knife
Battery terminal lugs
Lug crimper
Terminal kit
Terminal crimper
Hammer
Step 1

Mount the battery switch with the mounting kit provided by the manufacturer. The switch should be accessible but close to the battery or battery banks.
Step 2
Mount the battery charger in a location that will be accessible but protected from the elements. Mount the charger close to the battery switch to reduce the size of the charger leads.
Step 3
Connect the battery cables to the battery switch. Mount the battery cables onto their corresponding terminal studs on the battery switch.
Step 4
Lay out the battery positive cable from the charger to the switch and cut it to length with the cable cutters. Strip 3/4 inch of insulation from the cable ends with a razor knife. Splice the cable to the hot wire from the charger with a **** connector and the terminal crimper. Crimp a terminal lug onto the battery end of the cable with the lug crimper and a hammer. Connect the terminal lug at the battery switch positive output terminal.
Step 5
Lay out a battery cable from the charger to the battery negative terminal block. Cut the cable to length and strip 3/4 inch of insulation from the ends with a razor knife. Connect the battery negative cable to the charger negative power lead with a ****-splice and the terminal crimpers. Crimp a terminal lug onto the terminal block end of the cable with the lug crimper and a hammer. Connect the terminal lug at the battery negative terminal block post.

Tips & Warnings
Set the switch to "1," "2" or "both" to charge battery bank 1, bank 2 or both batteries at once.

on Jan 07, 2010 | Mercedes-Benz C230 Cars & Trucks

2 Answers

Battery releases charge after being parked for about 15 mins


sounds like you may not have enough liquid in the battery ,but if the battery is full of water,it sounds like you may have a dead cell or cell's,check the battery with a load tester,after charging the battery,take the neg.battery cable off the battery,then in a few min.test the battery with a load tester,

Dec 30, 2012 | 1995 Nissan Quest

2 Answers

Battery light


On this issue i suggest you to get the battery and its connections checked.
Either battery is got weak or the problem is related to loose battery connections.Some times battery connectors gets dirty and cause no connection issue.So disconnect battery terminals,clean them and reconnect and check ,if that is helping.
Also if the battery is got very old,then try with new battery.

For more detailed help,related to these issue,i suggest you to click the help links provided below:-----

Battery light stays steady ON? http://technoanswers.blogspot.in/2012/02/ford-ranger-battery-light-stays-steady.html

----------------
Battery Light and ABS Light on Dash http://whoisbyme.blogspot.in/2012/07/battery-light-and-abs-light-on-dash.html

------------
Battery Warning Light Flashing on Dash? http://whatisbyme.blogspot.in/2012/05/2007-toyota-rav4-battery-warning-light.html

-----------------
Service Battery Warning Light On Dash? http://whoisbyme.blogspot.in/2012/06/service-battery-warning-light-on-dash.html

---------------
How to Inspect Car battery? http://repairhelpcenter.blogspot.com/2011/12/how-to-inspect-car-battery.html--------- How to Test Car Battery? http://repairhelpcenter.blogspot.com/2011/12/how-to-test-car-battery.html--------- Car Battery Servicing? http://repairhelpcenter.blogspot.com/2011/12/car-battery-servicing.html--------- How to Replace Car Battery? http://repairhelpcenter.blogspot.com/2011/12/how-to-replace-car-battery.html-------- How to Inspect Car battery Terminals? http://repairhelpcenter.blogspot.com/2011/12/how-to-inspect-car-battery-terminals.html-------- How to clean car Battery terminals? http://repairhelpcenter.blogspot.com/2011/12/how-to-clean-car-battery-terminals.html---------- How to Replace Broken Car Battery Cables? http://repairhelpcenter.blogspot.com/2011/12/how-to-replace-broken-car-battery.html

---------
These details will help.
Thanks.

Oct 06, 2012 | Cars & Trucks

2 Answers

HOW TO TAKE OUT BATTERY 2003 OLDS SIL


Remove wiper assembly plastic cover. Then remove front bolt that holds the cross brace bar over the battery. Loosen the bolt at the other end of the brace bar and rotate brace bar from over the battery to a new location and proceed to remove the plastic battery hold down mount on bottom of battery.Disconnect the negative then positive battery cables from the battery then rotate battery up and out of compartment -- this is a very tight fit. It will come out and the clearance is very small. This is a neat challenge. Be sure to buy proper size battery for replacemeent

Read more: http://wiki.answers.com/Q/How_do_you_remove_a_battery_from_an_Oldsmobile_Silhouette#ixzz1noNX2HXJ

Feb 29, 2012 | Cars & Trucks

1 Answer

I need a new battery for my 1986 Oldsmobile ninety-eight regancy sedan. fully loaded. what type of battery would i need?


Attributes Battery BCI # : 75
Battery CA @ 32 Degrees F : 775
Battery CCA @ 0 Degrees F : 630
Battery Height : 7 1/4"
Battery Length : 9 3/4"
Battery Posts Type : Side Post
Battery Reserve Capacity : 90
Battery Voltage : 12 volt
Battery Weight : 33 lbs.
Battery Width : 7"
Wet or Dry : Wet
A lead acid battery with the fallowing specs
group 75



Attributes Battery BCI # : 75
Battery CA @ 32 Degrees F : 775
Battery CCA @ 0 Degrees F : 630
Battery Height : 7 1/4"
Battery Length : 9 3/4"
Battery Posts Type : Side Post
Battery Reserve Capacity : 90
Battery Voltage : 12 volt
Battery Weight : 33 lbs.
Battery Width : 7"
Wet or Dry : Wet
Attributes Battery BCI # : 75
Battery CA @ 32 Degrees F : 775
Battery CCA @ 0 Degrees F : 630
Battery Height : 7 1/4"
Battery Length : 9 3/4"
Battery Posts Type : Side Post
Battery Reserve Capacity : 90
Battery Voltage : 12 volt
Battery Weight : 33 lbs.
Battery Width : 7"
Wet or Dry : Wet
Battery BCI # : 75
Battery CA @ 32 Degrees F : 775
Battery CCA @ 0 Degrees F : 630
Battery Height : 7 1/4"
Battery Length : 9 3/4"
Battery Posts Type : Side Post
Battery Reserve Capacity : 90
Battery Voltage : 12 volt
Battery Weight : 33 lbs.
Battery Width : 7"
Wet or Dry : Wet

Feb 27, 2011 | 1986 Oldsmobile Regency

2 Answers

I just bought a new battery for my 2006 chevy cobalt. The original battery has a vent tube from the battery to the car. However, the new battery is lacking a spot, I think? Where is the hole for this new...


The Interstate battery is a sealed battery, meaning no vent. It is a better and higher quality battery than the factory battery.


Please take a moment and rate my answer...........Thanks

Dec 01, 2010 | 2006 Chevrolet Cobalt

1 Answer

Battery size for a 2003 chevy tracker


Here is the information on the battery size from NAPA. The CA(cranking amps) and CCA(cold cranking amps) can be changed within a certain amount but the dementions should stay the same as well as it being a top post battery.

Battery CA @ 32 Degrees F : 780
Battery CCA @ 0 Degrees F : 625
Battery Height : 8"
Battery Length : 9 1/16"
Battery Load Test Amps : 312.5
Battery Posts Type : Top Mount
Battery Reserve Capacity : 95
Battery Voltage : 12
Battery Weight : 32.5
Battery Width : 6 13/16"

Nov 16, 2010 | 2003 Chevrolet Tracker

1 Answer

Need procedure to remove and replace the battery in a 2006 PT Cruiser


BATTERY

GASOLINE ENGINE

REMOVAL

WARNING:
  • TO PROTECT THE HANDS FROM BATTERY ACID, A SUITABLE PAIR OF HEAVY DUTY RUBBER GLOVES SHOULD BE WORN WHEN REMOVING OR SERVICING A BATTERY. SAFETY GLASSES ALSO SHOULD BE WORN.
  • REMOVE METALLIC JEWELRY TO AVOID INJURY BY ACCIDENTAL ARCING OF BATTERY CURRENT
  1. Make sure ignition switch is in OFF position and all accessories are OFF.
  2. Open hood.
  3. Remove the air cleaner housing.
  4. Disconnect and isolate the battery negative cable then the positive cable.
  5. Loosen bolt (4) and retainer (1) that holds the battery down to the tray.
  6. Lift battery out of battery tray and remove from vehicle.
  7. Remove thermal guard (if equipped) from battery.

CAUTION: Vehicles equipped with the turbocharged engine use a unique battery hold down. If the replacement battery is not identical, in size to the original, it may be necessary to use non-corrosive spacers on top of the hold down retainer to properly secure the battery in the battery tray.


When replacing battery, the thermal guard MUST be transferred to the new battery (if equipped).
  1. Install battery in vehicle making sure that the thermal guard (if equipped) is present and battery is properly positioned on battery tray.
  2. Install battery hold down hardware (1), (2), (3) and (4) making sure that it is properly positioned on battery. Torque clamp to 12.5 N.m (110 in. lbs.) .
  3. Install battery cables on battery posts. Install battery positive cable first.
  4. Torque clamp nuts to 12.5 N.m (110 in. lbs.) .
  5. Install air cleaner housing.
  6. Close hood.
  7. Verify proper vehicle operation.


Jul 15, 2010 | 2006 Chrysler PT Cruiser

2 Answers

Dead battery


Removal Procedure

Disconnect the negative battery cable

Remove the wheelhouse liner.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.


Install the battery hold down retainer and bolt.

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts.

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Install the positive battery cable (1).

Tighten the positive battery cable bolt.

Close the positive battery cable connection cover.

Install the wheelhouse liner.

Connect the negative battery cable

Oct 15, 2009 | 2006 Pontiac Solstice

Not finding what you are looking for?
2005 Chevrolet Equinox Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...