Question about 1998 GMC Safari

1 Answer

Removing inside door panel 1998 safari van

Okay typical Saturday project but can't figure out how to get the door panels off the passenger side and the rear door. Phoned GM and found the screws they were talking about but still can't get panel off of door. Is there clips or ? Was told parts are discontinued and to be careful.

Posted by on

  • Anonymous Dec 01, 2008

    broken rear door handle

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Rear hatch door on 2000 gmc safari will not unlock-how can I open it?

Posted on Jan 11, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove passenger side door panel?


no, the pull strap for closing the door contains hidden screws. the inside door handle must be uncovered for hidden screw the armrest has screws.

Apr 01, 2013 | 1998 Lincoln Town Car

1 Answer

1998 Ford F150 supercab - passenger side door won't open


Get inside the backseat remove two screws that hold the side window. Gently pull the top plastic panel out all around and the panel will come out. It is held by about six clips. Then remove the screws and a nut off the bottom panel. These are all at the top of the bottom panel. Remove a couple of screws thatholds the inside doorl latch. Once all out then simply lift up on the bottom panel and it will come out. Remove the plastic sheet that overs the side door underneath the panel. Now you can see the whole mechanisim for the unlatch. On my truck the problem was with the top cable going into the latch mechanisim. The top cable came loose, out of the slot that held it in place. I pit it back into the slot and made a metal clip to keep it in place. If your interested I can add picture of the clip. Reassembled the door and was done in about three hours.

Jan 12, 2012 | 1999 Ford F150 Regular Cab

1 Answer

On a 1998 expedition, where is the pcm and the ecm--5.4 litre


1998 Ford Truck Expedition 4WD 5.4L EFI 8cyl

PCM Ford's Location:
* Ranger - behind instrument panel (cowl), center to both driver and passenger sides.
* Explorer/Mountaineer - behind instrument panel (cowl), (access from engine compartment dash panel) on passenger side to center of vehicle.
* All other F-Series, Expedition/Navigator - lower dash panel on passenger side.
* Excursion - lower dash panel on driver side.

The PCM is behind the glove box and has a big harness connector in the firewall that you access from the engine compartment.

REMOVAL & INSTALLATION

a927c58.jpg

Fig. 1 The calibration number will be needed to order such parts as a replacement PCM, various sensors, and almost any emission control component. Typically this number is attached to a label found on the driver's door or the door pillar


1997-00 F-150, F-250, Expedition and Navigator

00a02b5.jpg

Fig. 2 Loosen the connector retaining bolt and remove the PCM connector

2cda058.jpg

Fig. 3 Remove the passenger side front door scuff plate

1fe310f.jpg

Fig. 4 Remove the passenger side kick panel

234c3f5.jpg

Fig. 5 Remove the PCM bracket clip and remove the PCM
  1. Remove the battery and the battery tray.
  2. Loosen the connector retaining bolt and remove the PCM connector.
  3. Remove the passenger side front door scuff plate.
  4. Remove the passenger side kick panel.
  5. Remove the PCM bracket clip.
  6. Remove the PCM.
To install:
  1. Installation is the reverse of removal.
  2. Tighten the PCM connector retaining bolt to 36-44 inch lbs. (4-5 Nm).

Hope helps.

Jul 13, 2010 | Ford Expedition Cars & Trucks

1 Answer

I recently purchased a used 03 Chevy Venture van. The passenger sliding door doesn't open. It worked for 1 week and stopped. The driver side sliding door has a broken handle so I'm able to open that door...


Pain but fixable. Sounds like the linkage is not connected. Even a mechanic will have to remove the door panel and fight with it. If you can remove the rear seat from the drivers side side door then you might have room to remove the passenger side door panel to fix it. Usually clips are the first thing to break on door handle/latch linkages

Apr 06, 2010 | 2003 Chevrolet Venture Passanger

2 Answers

Where is the fuel pump relay located on a 1991 gmc safari van?


I think if equiped i mean IF"""" it should be inside back door left or right in side quarter panel take of removeable panel then you should gain getting at it! if equiped!

Dec 23, 2009 | 1991 GMC Safari

1 Answer

I have the Chevy Astro AWD 1998 passenger van with the three part rear door (tilt up window and then split half doors). The handle broke off of the right side primary door. Is there a way to get the door...


just take off the inside panel and look inside the should be some tiny silver bars that either pull up or go side to side, then pull that should open it. also you can get to the handle from the inside access and replace from an auto parts store

Dec 16, 2009 | 1998 Chevrolet Astro

1 Answer

How to replace inside door handle on passenger on 1998 chevy silv


Remove screw from inside door grab handle. Remove door panel by carefully prying out plastic clips. Drill or chisel off pop rivets holding the handle on. Pull handle out far enough to disconnect linkage and remove handle. Install new handle and secure to metal panel with new pop rivets or sheet metal screws. It may be easier to reconnect linkages by removing the metal panel also.

Apr 11, 2009 | 1998 Chevrolet K1500

1 Answer

1998 safari van - removal of passenger internal door panel


You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. then you just remove the bolts to the mirror

Mar 22, 2009 | 1998 GMC Safari

2 Answers

98 caravan power windows


its most likely the switch on the drivers door.. to checj it remove the door panel and connect a test light to both of the wires that are in the motor plug then operate the switch in both directions if the light turns on in both directions then its the motor..

Jan 25, 2009 | 1998 Dodge Grand Caravan

1 Answer

Replacing exterior door handles 1998 Safari van


remove door panel.. inside door you will see a rod going to the handle..on the end is a clip ..push the clip up off the rod .slide the rod out..remove 2 ..13mm nuts from handle ..remove handle

Nov 14, 2008 | 1998 GMC Safari

Not finding what you are looking for?
1998 GMC Safari Logo

880 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...