Question about 2006 Chevrolet Uplander

Open Question

Electrical problem with power sliding door Chevy Uplander

The switches either near the door or up on the console sometimes do not operate the right power sliding door. When they do work, the warning beeps tell me that the door has not closed properly. It is closed, but I can hear the mechanism working as if it was trying to close the door. Is there a remedy I can try before I take the car into the dealer?

Posted by on

  • blaze2000 May 10, 2009

    wouldn't open, only made a buzz sound like a warning, maybe that something was in the way? tried reset procedure in manual, now no sounds or anything, all good fuses


×

5 Suggested Answers

  • 840 Answers

SOURCE: The electric door will not close on my 2005 chevy uplander

the latch needs to be replaced Please rate my response thank you very much

Posted on Feb 02, 2009

  • 82 Answers

SOURCE: 2006 Chevy Uplander. The power sliding doors won't shut

2 possible solutions. First clean the door pin contacts(multiple spring loaded pins on door side and matching plate on body) with a scotch pad until shiny gold color again. Second the rear edge of the door should be 1mm inside the body opening when closed. If those are correct it is going to take a software download from a dealer to the door control module to fix this. Otherwise you will have to pull the psd fuse and breaker from the right side dash fuse box.

Posted on Jun 23, 2009

  • 4332 Answers

SOURCE: chevy uplander sliding door sensor will not stop

Look closely at the door switches. Sometimes they get compressed too far and no longer indicate a closed door...
the way these switches work, is the FIRST close of the door compresses the switch, meaning that the switch can be pushed into itself... this auto adjusts for differences across different door gaps....

If you have only contact points for the door, be sure that those contacts are totally clean, then test again.

Doc

Posted on Sep 17, 2009

  • 58 Answers

SOURCE: Chevy Uplander (2006) when sliding doors are

One or more of your sliding door may have lost their learned opened/closed position.Also the door may be binding,obstructed or need a latch adjustment.If a relearn is required return to a GM dealership as a diagnostic scan tool is required.

Posted on Oct 28, 2009

  • 3 Answers

SOURCE: chevy uplander sliding door sensor will not stop

Remove the PSD fuse, its on the inside fuse panel

Posted on Jan 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the rear heater motor located on 2008 uplander


If the van has E59 on the RPO sticker you have to remove the left rear lower trim panel to access the motor. If it does not have E59 just remove the left rear compartment lid and compartment to access the motor. RPO E59 is a power left sliding door.

Sep 24, 2014 | 2008 Chevrolet Uplander

1 Answer

Were are the fuses for the power sliding door in 2005 chevy uplander


http://www.carcarekiosk.com/video/2008_Chevrolet_Uplander_LS_3.9L_V6/fuse_interior/replace

Jan 31, 2013 | 2007 Chevrolet Uplander LS Minivan

1 Answer

Where is located the keyless module in Chevy Uplander 2006


Have you tired reprogramming the remotes top work the module first, that is what must be done before any parts are replaced, they do loose programming for no apparent reason at times. This can be causes by an electrical magnetic pulse of some sort.

Aug 17, 2012 | 2006 Chevrolet Uplander

2 Answers

Door chime on 2007 chevy uplander will not stop even when the door is closed properly. Is there anyway to disable it


unfortunately the fuse that runs the chime also runs other items on that circuit so pulling the fuse isn't an option, basically what you need to do is check each door switch , one is shorted, and is in the open position,, they are located at the side rails of each door, remove the deco rubber trim, and you will see that a screw holds them on, they pop right out, with a meter, check each switch for continuity with the switch in the OUT position, when the switch is depressed, you should get no reading, since that closes the circuit, you can either replace the bad switch, ( sometimes they just get stuck,m so move them around and spray some electrical contact cleaner on each one) BY the way,, on this model of vehicle, there have been a number of issues with the sliding door latch ,, here are some of the issues ,, http://www.lemonlawclaims.com/Chevrolet_uplander_sliding_door.htm

Sep 10, 2011 | 2007 Chevrolet Uplander LT Minivan

2 Answers

Door chime on 2007 chevy uplander will not stop even when the door is closed properly. Is there anyway to disable it without disabling radio


Had this problem for some time. I have had the dealer replace motor etc. Problem still returns. Noticed that the foam seal around the right side door has started flatening out over time and was beginning to spill into the lipped plate that the door sensor buttons possibly could be prevented from making proper contact. Trimmed approx. 3/8 of an inch off the foam in the area of the plate, and the problem seems to have gone away. Hope this helps.

Apr 25, 2010 | 2007 Chevrolet Uplander LT Minivan

2 Answers

The door chime on our 2005 Saturn Relay Van continuously goes off when you put it in gear. There are no obstructions but the automatic door switch fails to open the door sometimes and other times the chime...


I have a 2006 SV6 with the power sliding doors. The problem that I found was with the contacts on the door ( They are called plungers) the movable pins were losing connection with the fixed part The plunger is very easy to replace if you can find one. The plungers are covered with a rubber cover and is held in place with 2 plastic pins. My Pontiac dealer could not even find one in his books or even a picture of one, and claimed that he had never had anyone come with a door problem. My Chevy dealer said that it came with a wiring harness that is not needed for $154. The cure that I came up with was to take the plunger block apart (it snaps together)and replace the rusted out springs then solder 3" wires to the end of the plunger pins (they solder easy) to the tabs that go to the plug(pop out the tabs or you will melt the plastic. It took about 45 min. now the doors work like new and will never loose contact again

Oct 06, 2009 | 2005 Saturn Relay

2 Answers

Chevy uplander sliding door sensor will not stop


Remove the PSD fuse, its on the inside fuse panel

Sep 17, 2009 | 2002 Chevrolet Uplander

5 Answers

2006 Chevy Uplander. The power sliding doors won't shut


2 possible solutions. First clean the door pin contacts(multiple spring loaded pins on door side and matching plate on body) with a scotch pad until shiny gold color again. Second the rear edge of the door should be 1mm inside the body opening when closed. If those are correct it is going to take a software download from a dealer to the door control module to fix this. Otherwise you will have to pull the psd fuse and breaker from the right side dash fuse box.

Jun 23, 2009 | 2005 Chevrolet Uplander

Not finding what you are looking for?
2006 Chevrolet Uplander Logo

Related Topics:

333 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63577 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...