Question about 2005 Chrysler Town & Country

Open Question

Parking assist lights stay on

When I back out of the garage in the morning the parking assist lights come on and stay on. An alert displays Service Parking Assist System Soon.

Posted by on

5 Suggested Answers

  • 1779 Answers

SOURCE: what does "service park assist system" mean on my 2008 jeep?

The park assist system detects objects 59 inches or less in back of your vehicle, to warn u so u don't strike the object. I'm guessing that since the service park assist system comes on in the ice and snow, the monitor is detecting something (ice and snow covering the sensor). If u clean off the snow and ice, the message should shut off.

Posted on Jan 13, 2009

  • 7409 Answers

SOURCE: parking assist not working nor backup cam

check fuse, relay,and switch if u have a hitch hooked up or something blocking sensors in bumper remove or clear obstruction also extreme dusty or dirt build up can cause problem

Posted on Oct 28, 2009

raygin
  • 322 Answers

SOURCE: Bad parking assist sensor.....is there a fuse for the park assist?

This is a shared fuse, if you remove it you will lose other services. As your reverse aid sounds all the time it has a probable fault in the module or wiring. The module is located in the left hand side lower boot. To disable - pull the plugs from the module until you get it checked out. These modules often suffer from dampness in the boot as it is prone to leaking. sometimes just removing and refitting the plugs and then spraying with a water dissipating spray (WD 40) often brings them back to life once they have dried out.
hope this helps - good luck.

Posted on Jan 20, 2010

  • 1 Answer

SOURCE: how do you service park assist system on a grand

I got a 2007 jeep grand cherokee diesel and at times the service park assist will flash and the engine light will come on. a box forms around the gears on the display and it feels like it trannys slipping and its rough out of 1st gear. if you throw it in neutral then back to drive everything is fine again. After hours of research i found that you have to get your computer flashed. It if commom for many people and the dealership wont know what your talking about. so you have to lets them know!!!! else they have no clue

Posted on Jan 29, 2010

  • 1 Answer

SOURCE: the service park assist light comes on my yukon denali

what is the process on how to reset the rear park assist light that comes on the instrument cluster on the dash?

Posted on May 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I bought this car a week ago. (A 2001 buick lesabre limited). I drove it home and haven't gotten it insured yet so for the past week while I was on vacation I parked it in my garage and shut it so it would...


Lets start at the beginning. Have you checked the oil and coolant to make sure they are full ? Did it leak anything on the garage floor while it was parked ?
You could have oil or power steering fluid leaking onto the exhaust pipe which would cause a great deal of smoke.
And on most cars the check engine light will be on until the engine starts. If it stays on after the engine is running, you have trouble codes stored in the computer.

Aug 04, 2014 | Cars & Trucks

1 Answer

I've 2000 Mercedes Benz ML 320.One night I backed up & parked in the Garage the next morning it won't go forward. I noticed the that REAR WHEEL on passenger side was locked up. What's


The only suggestion is to place the vehicle on
stands & remove the wheel to check out the issue

To speculate from the internet-- is just that.

To have something happen while you sleep
is odd,so I would be inclined to go with something
like an electronic parking brake issue,if that applies

Nov 14, 2012 | 2004 Kia Sedona

1 Answer

GMC 07 Serria backup sensor will not work. I had a new bumper installed. At first it beeper all the time. Now it will not come on. The DIC shows park assist off.


#PIT4878: Service Park Assist Message / LEDs Stay On Or Inop - keywords B0968 inoperative lamp led light lit module reverse urpa - (Jun 12, 2009) 999999995.gif Subject: Service Park Assist Message/ LED's Stay On or Inop Models: 2007-2009 Chevrolet Silverado 2007-2009 GMC Sierra With RPO UD7

The following diagnosis might be helpful if the vehicle exhibits the symptom(s) described in this PI.
Condition/Concern: Some customers my comment of a Service Park Assist Message on the DIC and/or the LED indicators at the right rear pillar staying on or inoperative. This concern could be caused by the wiring harness to the LED indicators being pinched under a ground eyelet at the right rear pillar, as shown below.

2290161.gif
other issues could be the problem such as poor connections at each sensor or damaged sensors. to clear URPA codes,place ignition in run,(engine OFF),shift into reverse and turn key OFF.place shift lever into park and retest operation of URPA. if still inop URPA code(s) need to be retrieved before further diagnosis can be accurately done.

Sep 15, 2011 | 2007 GMC Sierra 1500

1 Answer

My park assit is on and the sensor are not working for backing up can they have dirt in them


{: ) The PARK ASSIST OFF message will be displayed when the parking assist system is disabled due to conditions that disable or inhibit the system. The object alarm module requests the DIC display PARK ASSIST OFF when it detects one of the following conditions:
• The parking assist system is manually disabled using the driver information center (DIC). • An object is attached to the rear of the vehicle, such as a trailer, bicycle rack, trailer hitch receiver, or tow bar. • The object alarm sensors are covered by snow, mud, dirt, slush, or ice. • The vehicle bumper is damaged. • Excessive paint thickness on a replacement object alarm sensor. • The object alarm sensors are disrupted by vibrations, like those caused by a large nearby vehicle or from heavy equipment such as a jackhammer.

The SERVICE PARK ASSIST message will be displayed when the object alarm module detects a malfunction in the parking assist system and the system is disabled. It could be one of your sensors is at fault or even the module.

May 18, 2011 | 2007 GMC Yukon Denali

3 Answers

The park assist service light comes on when i start the vehicle. i do not have an owners manual to reference.


{: ) The driver information center (DIC) displays SERVICE PARK ASSIST when the object alarm module detects a malfunction in the parking assist system and the system is disabled. The DIC also displays SERVICE PARK ASSIST when a loss of communication occurs with the object alarm module. Usually this is caused by faulty components or wirings. Better visit your dealer if still under warranty, for one park assist sensor only costs too much. If your bumper had been knocked off or had previous repairs outside the dealership, that's another thing.
The PARK ASSIST OFF message is displayed in the DIC when the parking assist system is disabled due to conditions that disable or inhibit the system. The object alarm module requests the DIC display PARK ASSIST OFF when it detects one of the following conditions:
• The parking assist system is manually disabled using the driver information center (DIC). • An object is attached to the rear of the vehicle, such as a trailer, bicycle rack, trailer hitch receiver, or tow bar. • The object alarm sensors are covered by snow, mud, dirt, slush, or ice. • The vehicle bumper is damaged, • Excessive paint thickness on a replacement object alarm sensor. • The object alarm sensors are disrupted by vibrations, like those caused by a large nearby vehicle or from heavy equipment such as a jackhammer.

Apr 14, 2011 | 2009 GMC Yukon

1 Answer

Park assist warning came on.


{: ) SERVICE PARK ASSIST The driver information center (DIC) displays SERVICE PARK ASSIST when the park assist module detects a malfunction in the object detection system and sends a request to the DIC for display of the message. The DIC also displays SERVICE PARK ASSIST when there is a loss of communication with the park assist module.
PARK ASSIST OFF The PARK ASSIST OFF message is displayed in the DIC when the park assist system is disabled due to conditions that disable or inhibit the system. The red LED in the rear display, as well as, the telltale in the switch will be lit, notifying the driver the PARK ASSIST system is disabled. The object alarm module requests the DIC via the serial data circuit to display PARK ASSIST OFF when it detects that one of the following conditions is true:
• The object alarm system is disabled through DIC vehicle customization feature. Refer to the Owners Manual for more information. • An object is attached to the rear of the vehicle, such as a trailer, bicycle rack, or hitch receiver. • An object is hanging out of the endgate. • The park brake is not fully released. • The system receives vibrations from a large nearby vehicle or from a heavy equipment such as a jackhammer. In the case of objects attached to the rear of the vehicle such as a trailer, hitch receiver, or a bicycle rack, or objects hanging out of the endgate, the rear parking assist (RPA) will have an Automatic Object induced disable feature where the RPA will determine if the rear object is moving with the vehicle. If the RPA detects such a condition, the park assist will be disabled. The PARK ASSIST OFF message will continue to be displayed until the trailer hitch receiver is removed and the vehicle is driven forward above 24 km/h (15 mph).

Feb 07, 2011 | 2007 GMC Yukon Denali

1 Answer

The parking brake lights stays on and the dash board parking brake light stays on also makes horrible buzzing sound when driving. I big explanation mark in the driver display in the center of the counsel.


Possible problems are :

Low Brake Fluid.

Low Brake Assist pressure .( Some Models.)

Faulty Pad Warning sensors.

Brake sensor loom fault.

Faulty Park Brake Switch...or wiring.

Faulty Brake Switch.

Jan 12, 2011 | Audi A6 Cars & Trucks

3 Answers

The check air bag light stays on , and a service air bag alert at info center


Sounds like the sensor is tripped due to low pressure in the compressor you have to get the unit charged and the light will go off. Or take it to a auto parts store and have them put their diagnostic code reader on their and have them clear the codes this may fix it as well

Oct 17, 2008 | 1997 Cadillac Seville

1 Answer

Transmission Shifting Problem, 1995 Seville with Northstar and approx. 70,000 miles


A bad IAC (idle air control)or vacuum leak. Check for bad vacuum hoses first, the IAC is around $50

Jun 22, 2008 | 1995 Cadillac Seville

Not finding what you are looking for?
2005 Chrysler Town & Country Logo

Related Topics:

382 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

64052 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...