Question about 2002 Audi A4

1 Answer

How to disconnect coil wire

I want to change spark plugs on my audi a4 3.0, but i'm not sure how to disconnect the connectors from the coil ( I try push on the tab and pull, but its not coming off!) Thanks. mike

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 345 Answers

A very small screwdriver under where the connector fits the coil pack will lift the tag so you can get it off....they are not the easiest connectors to get off...............

Posted on Nov 22, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change a coil pack on a Chevy Tahoe


To Remove......
1. Remove the spark plug wire from the ignition coil.
2. Disconnect the ignition coil electrical connector.
3. Remove ignition coil bolts.
4. Remove ignition coil.

To Install.....
1. Install ignition coil.
2. Install ignition coil bolts.
3. Tighten ignition coil bolts to 8 Nm the same as 71 inch pounds.
4. Connect ignition coil electrical connector.
5. And finally, install spark plug wire to ignition coil.

Apr 22, 2015 | Chevrolet Tahoe Cars & Trucks

Tip

How to fix EPC light ON from AUDI


The best ideea is to scan your Engine Control Unit with a VAG-COM, Bosch KTS, ... diagnosis tool. If you have one of these dedicated scan tools you will find definitely the engine fault code-"P...." and the clear description of the error. Also you can try to erase this error (or these errors) from the Engine Control Unit memory. If errors are "sporadic" type you certain have permission to erase them, also for some kinds of "static" errors. Because your Engine "MIL" - Malfunction Indicator Lamp keeps coming "ON" and "OFF" you have a big good hand to clean errors from Engine Management System memory. If you don't have any diagnosis tool, you can also try something else. For check up if the engine have a proper turn, you can successively disconnect each spark plug coil from the engine wiring system, engine idle, car stationary. When you operating this you must be free of chassis ground (battery ground)!!! When you disconnect a spark plug coil and the engine speed (rpm) drops, that means this coil works properly. When one coil disconnected and engine speed (rpm) still remain unaltered, this coil (or spark plug) is out of order. First you can change only the spark plug and check up again. If no changes the coil is defective and must be replaced! My recommendation is first to change all spark plugs on the engine, and after that check up coils.

on Dec 19, 2009 | Audi A4 Cars & Trucks

1 Answer

Spark plugs


Check this SPARK PLUG REPLACEMENT - REMOVAL PROCEDURE

1_23_2012_5_10_32_pm.jpg

1. Remove the ignition coils (lines at end this document), then return here once you have gotten the Coil
Packs off and precede with step 2 from here.
2. Clean the spark plug recesses with low pressure air. CAUTION: Wear safety glasses
when using compressed air, as flying dirt particles may cause eye injury. NOTE:
Clean the spark plug recess area before removing the spark plug. Failure to do so could
result in engine damage because of dirt or foreign material entering the cylinder head, or
by the contamination of the cylinder head threads. The contaminated threads may prevent
the proper seating of the new plug. Use a thread chaser to clean the threads of any
contamination.
3. Remove the spark plugs from the cylinder head. NOTE: Allow the engine to cool before
removing the spark plugs. Attempting to remove the spark plugs from a hot engine may
cause the plug threads to seize, causing damage to cylinder head threads.
4. Inspect the spark plugs.

INSTALLATION PROCEDURE

1_23_2012_5_11_30_pm.jpg

1. Measure the spark plug gap on the spark plugs to be installed. Compare the measurement
to the gap specifications. NOTE:
• Use only the spark plugs specified for use in the vehicle. Do not install spark
plugs that are either hotter or colder than those specified for the vehicle. Installing
spark plugs of another type can severely damage the engine.
• Check the gap of all new and reconditioned spark plugs before installation. The
pre-set gaps may have changed during handling. Use a round feeler gage to ensure
an accurate check. Installing the spark plugs with the wrong gap can cause poor
engine performance and may even damage the engine.
2. Install the spark plugs to the cylinder head. NOTE:
• Be sure that the spark plug threads smoothly into the cylinder head and the spark
plug is fully seated. Use a thread chaser, if necessary, to clean threads in the
cylinder head. Cross-threading or failing to fully seat the spark plug can cause
overheating of the plug, exhaust blow-by, or thread damage.
• Refer to Component Fastener Tightening Notice in Service Precautions.
Tighten the spark plugs to 18 N.m (13 lb ft).
3. Install the ignition coils.

IGNITION COIL(S) REPLACEMENT
REMOVAL PROCEDURE
1. Remove the air cleaner resonator and outlet duct.
2. Disconnect the engine wiring harness electrical connector (1) from the oil pressure sensor (2).
3. Disconnect the engine wiring harness retainers (1) from the power steering pump (2).
4. Disconnect the engine wiring harness electrical connectors (1, 4) from the following:
• The exhaust camshaft position (CMP) sensor (5)
• The camshaft position (CMP) actuator solenoid valve (6)
5. Disconnect the engine wiring harness retainer (2) from the camshaft cover (3).
6. Disconnect the engine wiring harness electrical connectors from the following:
• The engine coolant temperature (ECT) sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The heated oxygen sensor (HO2S) (5)
7. Disconnect the engine wiring harness electrical connector from the intake camshaft position (CMP) sensor.
8. Carefully disengage the engine wiring harness conduit from the camshaft cover, and position aside.
9. Remove the ignition coil bolts.
10. Remove the ignition coils from the camshaft cover.

INSTALLATION PROCEDURE
1. Install the ignition coils into the camshaft cover. IMPORTANT: Ensure the ignition coil seals are properly seated to the camshaft cover.
2. Install the ignition coil bolts. NOTE: Refer to Fastener Notice in Service Precautions. Tighten the ignition coil bolts to 10 N.m (89 lb in).
3. Attach the engine wiring harness conduit to the camshaft cover.
4. Connect the engine wiring harness electrical connector to the intake CMP sensor.
5. Connect the engine wiring harness electrical connectors to the following:
• The ECT sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The HO2S (5)
6. Connect the engine wiring harness electrical connectors (1, 4) to the following:
• The exhaust CMP sensor (5)
• The CMP actuator solenoid valve (6)
7. Connect the engine wiring harness retainer (2) to the camshaft cover (3).
8. Connect the engine wiring harness retainers (1) to the power steering pump (2).
9. Connect the engine wiring harness electrical connector (1) to the oil pressure sensor (2).
10. Install the air cleaner resonator and outlet duct.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jan 23, 2012 | Cars & Trucks

1 Answer

How to change spark plugs in a 2005 chev colorado


SPARK PLUG REPLACEMENT - REMOVAL PROCEDURE

1_23_2012_5_10_32_pm.jpg

1. Remove the ignition coils (lines at end this document), then return here once you have gotten the Coil
Packs off and precede with step 2 from here.
2. Clean the spark plug recesses with low pressure air. CAUTION: Wear safety glasses
when using compressed air, as flying dirt particles may cause eye injury. NOTE:
Clean the spark plug recess area before removing the spark plug. Failure to do so could
result in engine damage because of dirt or foreign material entering the cylinder head, or
by the contamination of the cylinder head threads. The contaminated threads may prevent
the proper seating of the new plug. Use a thread chaser to clean the threads of any
contamination.
3. Remove the spark plugs from the cylinder head. NOTE: Allow the engine to cool before
removing the spark plugs. Attempting to remove the spark plugs from a hot engine may
cause the plug threads to seize, causing damage to cylinder head threads.
4. Inspect the spark plugs.

INSTALLATION PROCEDURE

1_23_2012_5_11_30_pm.jpg

1. Measure the spark plug gap on the spark plugs to be installed. Compare the measurement
to the gap specifications. NOTE:
• Use only the spark plugs specified for use in the vehicle. Do not install spark
plugs that are either hotter or colder than those specified for the vehicle. Installing
spark plugs of another type can severely damage the engine.
• Check the gap of all new and reconditioned spark plugs before installation. The
pre-set gaps may have changed during handling. Use a round feeler gage to ensure
an accurate check. Installing the spark plugs with the wrong gap can cause poor
engine performance and may even damage the engine.
2. Install the spark plugs to the cylinder head. NOTE:
• Be sure that the spark plug threads smoothly into the cylinder head and the spark
plug is fully seated. Use a thread chaser, if necessary, to clean threads in the
cylinder head. Cross-threading or failing to fully seat the spark plug can cause
overheating of the plug, exhaust blow-by, or thread damage.
• Refer to Component Fastener Tightening Notice in Service Precautions.
Tighten the spark plugs to 18 N.m (13 lb ft).
3. Install the ignition coils.

IGNITION COIL(S) REPLACEMENT
REMOVAL PROCEDURE
1. Remove the air cleaner resonator and outlet duct.
2. Disconnect the engine wiring harness electrical connector (1) from the oil pressure sensor (2).
3. Disconnect the engine wiring harness retainers (1) from the power steering pump (2).
4. Disconnect the engine wiring harness electrical connectors (1, 4) from the following:
• The exhaust camshaft position (CMP) sensor (5)
• The camshaft position (CMP) actuator solenoid valve (6)
5. Disconnect the engine wiring harness retainer (2) from the camshaft cover (3).
6. Disconnect the engine wiring harness electrical connectors from the following:
• The engine coolant temperature (ECT) sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The heated oxygen sensor (HO2S) (5)
7. Disconnect the engine wiring harness electrical connector from the intake camshaft position (CMP) sensor.
8. Carefully disengage the engine wiring harness conduit from the camshaft cover, and position aside.
9. Remove the ignition coil bolts.
10. Remove the ignition coils from the camshaft cover.

INSTALLATION PROCEDURE
1. Install the ignition coils into the camshaft cover. IMPORTANT: Ensure the ignition coil seals are properly seated to the camshaft cover.
2. Install the ignition coil bolts. NOTE: Refer to Fastener Notice in Service Precautions. Tighten the ignition coil bolts to 10 N.m (89 lb in).
3. Attach the engine wiring harness conduit to the camshaft cover.
4. Connect the engine wiring harness electrical connector to the intake CMP sensor.
5. Connect the engine wiring harness electrical connectors to the following:
• The ECT sensor (1)
• The fuel injector harness (2)
• The ignition coils (4)
• The HO2S (5)
6. Connect the engine wiring harness electrical connectors (1, 4) to the following:
• The exhaust CMP sensor (5)
• The CMP actuator solenoid valve (6)
7. Connect the engine wiring harness retainer (2) to the camshaft cover (3).
8. Connect the engine wiring harness retainers (1) to the power steering pump (2).
9. Connect the engine wiring harness electrical connector (1) to the oil pressure sensor (2).
10. Install the air cleaner resonator and outlet duct.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jan 23, 2012 | Cars & Trucks

1 Answer

2004 audi a4 1.8 t misfiring flt code p0301 changed coils spark plug still showing code for cyl 1


try find out on the internet wats the problem with that code but take out the spark plug out of no 1 cilinder conected to the coil and turn over the engine and u will see if the spark plug will spark or not if is not sparking and the spark plugs and the coils are new may be from a wire or loose conection

Jan 12, 2011 | 2002 Audi A4

2 Answers

How do I replace the ignition coil in my 2002 ford taurus



Removal & Installation

3.0L (VIN S) Engine

  1. Disconnect the negative battery cable.
  2. Unplug the engine control sensor wiring connectors from the ignition coil and the radio ignition interference capacitor.
  3. Tag and disconnect the spark plug wires from the coil by squeezing the locking tabs, then twist the tab and pull upwards.
  4. Unfasten the four ignition coil retainers and remove the coil and the coil ground wire the radio ignition interference capacitor. Save the capacitor and coil ground wire for re-installation of the coil assembly.
  5. Wipe the coil towers with a clean cloth dampened with soap and water. Remove any soap film and dry with compressed air. Inspect the coil for cracks, carbon tracking, dirt or damage and replace as necessary.

    0996b43f802333d8.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Ignition coil assembly mounting-3.0L DOHC engines


To install:
  1. Place the coil, capacitor and the coil ground wire onto its mounting location on the right hand valve cover.
  2. Install the coil assembly retainers and tighten to 45-61 inch lbs. (5-7 Nm)..
  3. Apply dielectric compound D7AZ-19A331-A or its equivalent to the spark plug wire boots.
  4. Attach the spark plug wires to their proper terminals on the coil and make sure the boots are firmly seated so that the locking tabs engage.
  5. Attach the engine control wiring connectors to the ignition coil and the radio ignition interference capacitor.
  6. Connect the negative battery cable, start the vehicle and check for proper operation.

Dec 19, 2010 | 2002 Ford Taurus

1 Answer

There is a misfire in my engine, changed plugs & wires. now it reads that the fuel leveling sensor is bad, will this help?


If there is a misfire, the cylinder that it is misfiring in will be recorded as a code in the computer.

Have the car scanned to determine which cylinder is bad. Then, replace the coil pack going to that cylinder.

Ignition Coil Pack Removal & Installation 2V Engine To Remove:
  1. Twist the spark plug wires off of the ignition coil towers. Mark the spark plug wire positions so they can be installed in their original positions.
  2. Disconnect the electrical connector from the ignition coil. CAUTION
    When removing the spark plug wires, a slight twisting motion will break the seal and ease removal.
    coilconn.gif

  3. Remove the mounting screws and remove the ignition coil.
To Install:
  1. Position the ignition coil pack on engine.
  2. Install mounting screws and torque to 53 in-lbs. (6 Nm). coilbolt.gif

  3. Connect ignition coil pack electrical connector.
  4. Match previously marked spark plug wires to ignition coil and install.
4V Engine To Remove:
  1. Remove the RH cowl grille cowlpic.gif
  2. Remove the screws and the water shield
  3. Mark spark plug wire positions
  4. Disconnect the spark plug wires from the ignition coil CAUTION
    When removing the spark plug wires a slight twisting motion will break the seal and ease removal.
  5. Disconnect the ignition coil electrical connector coilconn.gif

  6. Remove the mounting screws and remove the ignition coil
To Install:
  1. Position ignition coil pack. Install mounting screws and torque to 56 in-lbs. (6Nm)
    coilbolt.gif

  2. Connect ignition coil pack electrical connector
  3. Match previously marked spark plug wires to ignition coil and install
  4. Position water shield and install screws
  5. Install RH cowl panel
prev.gif next.gif

Aug 11, 2010 | 2002 Ford Taurus

2 Answers

My 1991 Audi 80 will not start, engine cranks


Sounds to me like you may have left the air temp sensor or something electronic disconnected - Distributor - MAF sensor - go back and check and make sure that there's not an electrical pigtail somewhere hanging off - a vacuum leak wouldn't keep it from starting unless it were major - and your AUDI is mechanical injection I think - so fuel pull isn't a problem - check those connectors - let me know??? Thanks

Aug 21, 2009 | 1991 Audi 80

3 Answers

Coil pack. what and where is it? what does it look like?



 
 
Ignition Coil
Removal & Installation
4.2L Engine
1997-2000
To Remove:

Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The radio ignition interference capacitor connector
The locking tabs
The six ignition wires, marking for reinstallation
The brackets
The spark plug wire set
CAUTION
Spark plug wires must be connected to the proper ignition coil terminal. Mark spark plug wire locations before removing them.
The accelerator cable bracket nut
The accelerator cable bracket bolt
The accelerator cable bracket and position it aside.
The two ignition coil nuts
The ignition coil stud bolt
The ignition coil
To Install:
Install or connect the following:
The ignition coil
The two ignition coil nuts
The ignition coil stud bolt
Torque to: 71-98 inch-lbs (8-11 Nm)
The accelerator cable bracket
The accelerator cable bracket nut
The accelerator cable bracket bolt
Torque to: 71-98 inch-lbs (8-11 Nm)
The ignition coil electrical connector
The radio capacitor connector


CAUTION
The Spark plug wires must be connected to the proper ignition coil terminal.
Squeeze the locking tabs and connect the six ignition cables.
2001-2003
To Remove:

Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The spark plug wires, marking for reinstallation
CAUTION
The sparkplug wires must be connected to their correct ignition coil terminal.
The ignition coil
The bolts
Inspect the ignition coil for carbon tracks or damage.
To Install:
Inspect the ignition coil for carbon tracks or damage.
Install or connect the following:
The ignition coil
The bolts
Torque to: 53 inch-lbs (6 Nm)
The ignition coil electrical connector
The spark plug wires, in their original positions
4.6L Engine
1997-1999
To Remove:

NOTE: This procedure is for either RH or LH ignition coil.
Before servicing the vehicle refer to the precautions at the beginning of this section.
Remove or disconnect the following:
The ignition coil electrical connector
The radio capacitor electrical connector
The spark plug wires by squeezing the locking tabs (four each side)
CAUTION
The spark plug wires must be connected to their proper ignition coil terminal. Mark spark plug wire locations.
The bolts
The ignition coil
To Install:
NOTE: The procedure is for either LH or RH ignition coil
Install or connect the following:
The ignition coil
The bolts
Torque to: 44-62 inch-lbs (5-7 Nm)
The ignition coil electrical connector
The radio capacitor electrical connector
The spark plug wires (four each side), into their original positions by squeezing the tabs


CAUTION
The spark plug wires must be connected to their proper ignition coil terminal.

 
Top of Form 1
Bottom of Form 1

Mar 28, 2009 | 1998 Ford F150 Regular Cab

1 Answer

Spark plug change in a 1998 dodge intrepid


if you don t see any spark plug wires then your motor has coil packs(black colored boxwith 2 small electrical wires) located on top of motor 3 on one side,3 on the other.disconnect negative terminal on battery,then disconnect wire connector at each coil pack and remove 2 screws that hold down coil pack, pull gently straight up and plug is right there below coil pack

Jul 03, 2008 | 1998 Dodge Intrepid

Not finding what you are looking for?
2002 Audi A4 Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60792 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13152 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...