Question about 1998 Ford Contour

1 Answer

How do u put a 98 2.0 contour in time?

I had to change a pulley and i want to put the motor in time, what do i need to do?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert who has answered 20 questions.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 85 Answers

Use a straight edge across the back of the cams . on the flat spots good luck

Posted on Nov 23, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Where is my ign fuse located on my car

Below dash instrument panel, R16 ignition relay
98 Ford Contour SE Fuse Box Map
Fuse Panel Layout Diagram Parts: passenger side air bag, heater blower, interior lighting, heater blower motor, parking lamp, interior lighting, electric mirror, clock, wiper motor, ignition, reverse voltage protection, rear window defrost, engine management system, instrument panel illumination, radio, wiper motor, power windows, ABS module, backup lamp, brake lamp, door lock, main light, cigar lighter, electric seats,
link below should be the same as yours, press the helpful button

Jan 30, 2016 | 1999 Ford Contour

1 Answer

Is there a way to install a bypass belt for a burned out air compressor on a Ford Contour 2000, if so where and is there a manual or video instructions on how to do it yourself?

Don't know about the bypass belt, but what many do is buy and install an "A/C delete pulley"-a freewheeling pulley that is put on where the compressor mounts. Then you can use the same belt.

You would just have to check if such a pulley is made for Contours. Try parts stores, try,, even ask a parts person at ford dealer if he has heard of such a pulley for your car. All you need do is remove the compressor and install the delete pulley on the compressor mounting bracket.
Another choice is if contours came with no A/C, you might try a belt for a contour without a/c- sometimes this works, sometimes not, depending if other pulley driven units are mounted in the same place as yours with a/c.

Sep 30, 2013 | 2000 Ford Contour

1 Answer

Where is the location of the blower motor in a 98 Ford Contour?

Check the firewall on the driver or passenger side. Look for a wires leading to it in plastic conduit.

Also, the radiator has a blower motor on it to cool the antifreeze in the summer. That's another motor.

Jun 28, 2010 | 1995 Ford Contour

2 Answers

98 ford contour. Car sat for over a year. replaced plugs, wires, Battery, timing belt and pulleys, and fuel pump and screen, fuel filter. Car would run but wants to stall. Idles rough. Checked plugs and...

you may have to replace plugs again, sounds like the valve seals are dried out, That along with dead gas creates a bad cycle, Make sure you fill it up with the best octane fuel you can to off set the bad gas

Jun 16, 2010 | 1998 Ford Contour

2 Answers

98 Contour, starter ticks like dead battery and wipers cycle a couple of times when I turn the key to start. Wiper switch is in the off position, battery is fully charged. I would think possible starter...

If you turn the key and you hear a click and the motor is not moving your starter is probably bad. Everything can work on your car and the starter can be bad all by itself.
Check and see if your wiper is inthe correct position,sometimes we accidently move it without knowing.

Aug 08, 2009 | 1996 Ford Contour

1 Answer

98 contour heater worker stopped working

It's uner the dash, alot of time packages/people will loosen its one wire. If it also will not just blow on fan and is indead plugged in and has 12volt measuerd to ground it's a new fan motor you'll need.

Mar 12, 2009 | 1998 Ford Contour

Not finding what you are looking for?
1998 Ford Contour Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

81294 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides