Question about 2002 Jeep Liberty

1 Answer

P0340 code in my Jeep Liberty 2002

I want to know where that sensor is located.

Posted by on

  • blanca1323 Dec 09, 2008

    my truck will sputter when i start the engine and it makes a knocking noise.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 185 Answers

Since a P0340 Could be either the Cam Position Sensor or The Crank Position Sensor they are obviously in 2 different spots, however they both either sit on the back of the engine or on the transmission bellhousing. Your Cam Sensor is at the top and your Crank Sensor is near the bottom.

Hope this gives you some direction. Thanks for using FixYa!

Sincerely,

JC

Posted on Nov 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Luz marcada con el numero cinco?


2003 Jeep Liberty- Reading Engine / Diagnostic Codes ...

? 1:13
https://www.youtube.com/watch?v=pGrPBBzp7wE
Jan 6, 2013 - Uploaded by DeathScouter
2003 Jeep Liberty- Reading Engine / Diagnostic Codes ..... error code will flash 2 times, brief pause, flash 1 time, pause, flash 5times, pause, ...

2005 Jeep Liberty possible cause of P0442 error. - YouTube

? 5:26
https://www.youtube.com/watch?v=2ba-gH0gadg
Dec 21, 2014 - Uploaded by TheBGravit
While replacing a bad fuel pump I believe I found the cause of a P0442 Error code. I was able to repair the ...

Jeep Liberty Questions - Cylinder Misfire code - CarGurus

www.cargurus.com > Questions > Jeep > Liberty

CarGurusMay 27, 2009 - My jeep Liberty 2009 does the same the Dashboard showed a code of cylinder .... i have a jeep liberty 2006 with the # 5 cylinder misfire. i replaced the sparks... I have a 2005 Jeep Liberty 6 cylinder, engine light came on scaned the ... 2002 jeep liberty camshaft posistion sensor error code p0340 5 answers.

Check Engine Light/Misfire Due to Intake Valve Locks ...

repairpal.com > Problems > Jeep > Liberty
Recently got a second hand 2005 Jeep Liberty Sport. Everything worked fine ... #5intake valve seat dropped and held open the intake valve. 2008 Jeep Liberty.

OBD-II Trouble Code: P0305 Cylinder 5 Five Misfire Detected

www.obd-codes.com/p0305


Dec 08, 2015 | 2005 Jeep Liberty

2 Answers

I got a jeep 2.5 crd that doesnt want to start


Should be bolted to the right front side of the engine head.

The right side is as you are sitting in the drivers seat. Anytime car parts are labeled left or right it is as viewed from the driver's seat.

It you are facing the front of the engine it will be on your left.

Apr 30, 2014 | 2002 Jeep Liberty

1 Answer

Where is the camshaft position sensor on a jeep liberty 2.5 crd. car doesnt start show fault code p0340


on the right side of the engine block near the front engine mount for a four-cylinder engine

Apr 30, 2014 | 2002 Jeep Liberty

1 Answer

P0340 Problem Code for 03 Jeep Liberty


code p0340 refers to cam shaft position sensora bank 1-circuit malfunction===causes --wiring Cam sensor---ECM. The only connection is the ECM to both units so they may have unpluged the ECM to service the air bag problem. IT could be as simple as using a code reader to reset the CPU. I may also be a coincedence and there may be a fault in the cam position sensor.. I would discuss the matter with the dealer service department to determine what is what.

Oct 23, 2013 | 2003 Jeep Liberty

1 Answer

Fault code p0703


P0700 Transmission Control System Malfunction
P0730 Incorrect Gear Ratio
P0620 Generator Control Circuit Malfunction
P1130 Not found
P0340 Camshaft Position Sensor Circuit Malfunction

Mar 06, 2013 | 2002 Jeep Grand Cherokee

1 Answer

I have code P0320 and P0340 on my jeep liberty what does this mean


P0320 Ignition Engine Speed Input Circuit malfunction

P0340 Camshaft Position Sensor Circuit malfunction

Apr 15, 2010 | 2003 Jeep Liberty

1 Answer

I get a error code p0340 do you know what the problem is


For error codes clarification, visit http://www.troublecodes.net/OBD2/

Good luck and remember to rate this suggestion.

I love that car.

Aug 29, 2009 | 2002 Jeep Liberty

1 Answer

P0340 code


This indicates that a problem was detected in the camshaft position sensor circuit. Since it says circuit, that means the problem could lie in any part of the circuit - the sensor itself, the wiring, or the PCM.

A code P0340 could mean one or more of the following has happened:
  • a wire or connector in the circuit could be grounded/shorted/broken
  • the camshaft position sensor may have failed
  • the PCM may have failed
  • there exists an open circuit
  • a crankshaft position sensor may have failed
With a P0340 Code diagnosis can be tricky at times. Here are some things to try:
  • Visually inspect all the wiring and connectors in the circuit
  • Check for continuity in the circuit wiring
  • Check the operation (voltage) of the camshaft position sensor
  • Replace the camshaft position sensor as required
  • Check the crankshaft position circuit as well
  • Replace circuit wiring and/or connectors as required
  • Diagnose/replace the PCM as required
The location of these 2 sensors vary. Usually they can be found on the back of the engine or on the transmission. I hope this gives you some direction. Thanks for using FixYa!

Sincerely,

JC

Nov 21, 2008 | 2002 Jeep Liberty

6 Answers

2002 jeep liberty speed sensor


Jeep Liberty 2002 woahs !
by porth21 - 2/1/09 7:35 AM In reply to: Jeep Liberty 2002 speedometer not working by Dannywon
I have a 2002 Jeep Liberty Limited with the same problem. The main problem I have found to be the routing of the speed sensor wires located on the rear difrential. They are 2 blue wires on my jeep and probably the same on yours. The problem is that they rub on the E-brake cable and once the wire is exposed they short and the speedometer and any other options running off they speed sensor quit working and that includes the tranny shift points and can cause the torque converter to not unlock and cause stalls. I am having the same problem for the third time and chrysler and jeep are both aware of the problem and unwilling to repair the problem or post a recall.

Aug 06, 2008 | 2002 Jeep Liberty

Not finding what you are looking for?
2002 Jeep Liberty Logo

513 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...