Question about 1999 Chevrolet Blazer

1 Answer

1999 Blazer 4.3- license plate lamps inop and were changed with

For some weird strange reason the prndl and odometer light up when they decide to and the license plate lamps inop and were changed with known good parts

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

I had similar problems but 10 times worse than your's. After a $800 bill and 3 months later my problems were back. So I took it on myself. Under the hood on the drivers side wheel well you will find the 'Fuse Relay Center'. There is an enormous amount of wires (harness) that enter it from under it, between the box and the wheel well. I found that over the years wires had bared themselves and were shorting out on the wheel well. I located the worn wires, simply applied electrical tape to worn area then applied approx. 1/4" thick spacers between the bottom of the box and the wheel well at the bolts. You can use a stack of washers if needed. Two years and 45000 miles later, no electrical problem exists...yet. This is a very simple and inexspensive fix.

Posted on Dec 31, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why aren't parking lights working?


Park lamp fuse 20amp located in the under hood fuse box .DRL control module
Daytime Running Lamps (DRL) Control Module
Right of the steering column, behind the IP
Park, Sidemarker, Tail and License Lamps
Voltage is applied continuously to the PARK fuse to the headlamp and the instrument panel (IP) lamp dimmer switch through CKT 1340.
When the headlamp and the (IP) lamp dimmer switch is in the PARK or HEAD position, voltage is applied to CKT 9 thus activating the following lamps:
• The park lamps
• The side marker lamps
• The tail lamps
• The license lamps
The park/turn lamps are the only lamps that do not activate yet receive a current from CKT 9. The park/turn lamps do not activate because the voltage drop across the front side marker lamps is much higher than that across the turn lamp filaments Step
Action
Normal Result(s)
Abnormal Result(s)*

1
Turn the headlamp/instrument panel (IP) lamp dimmer switch to the PARK position.
The following lamps light:
• The license plate lamps
• The taillight lamps
• The front side marker lamps (Domestic)
• The front parking lamps (Domestic)
The headlamp position lamps (Export)
Refer to Park Lamps Inoperative
Park Lamps Inoperative
Step
Action
Value(s)
Yes
No

1
Inspect the PARK LP fuse.
Is the fuse open?
--
YES - Go to Step 2
NO - Go to Step 3

2
Repair a short to ground in CKT 1340.
Is the repair complete?
--
Go to Exterior Lights System Check
--

3
Turn the headlamp/instrument panel (IP) lamp dimmer switch to the PARK position.
Use a test light in order to backprobe the headlamp/IP lamp dimmer switch harness connector between terminal R and ground.
Did the test lamp light?
--
Go to Step 7
Go to Step 4

4
Use a test light in order to backprobe the headlamp/IP lamp dimmer switch harness connector between terminal O and ground.
Did the test lamp light?
--
Go to Step 5
Go to Step 6

5
Replace the headlamp/IP lamp dimmer switch. Refer to Headlamp Switch Replacement .
Is the repair complete?
--
Go to Exterior Lights System Check
--

6
Repair the following conditions in CKT 1340 between the PARK LP fuse and the headlamp and the IP lamp dimmer switch harness connector terminal O:
• A faulty connection
• An open circuit
Is the repair complete?
--
Go to Exterior Lights System Check
--

7
Repair the following conditions in CKT 9 between the headlamp and the IP lamp dimmer switch harness connector terminal R and S204:
• A faulty connection
• An open circuit
Is the repair complete?
--
Go to Exterior Lights System Check

Feb 18, 2016 | 1999 Pontiac Montana

1 Answer

Shift indicator lights up but does not display which gear I am in.


Odometer/Gear Shifter (PRNDL) Display FIX - GMC/Chevy ...

? 4:15
https://www.youtube.com/watch?v=-PQ-x11Vjng
Jan 24, 2012 - Uploaded by EricTehRedneck
Odometer/Gear Shifter (PRNDL) Display FIX - GMC/Chevy ...grease, it does in fact help insulate electrical connections but imnot sure lithium would help. .... i have a 2000 Chevy Astro van the park indicator goes out when you start ... volts but now the battery light stays on and the transmission will not shift ...

GM Electronic Gear Indicator and Tripometer Odometer ...

? 5:47
https://www.youtube.com/watch?v=jTQIVS_uB4g
Aug 11, 2010 - Uploaded by zcomputerwiz
Didn't light up anymore. ... Symptoms: PRND321 and Tripometer/Odometer no longer light. ... 2002 which the odometer and shift indicator do not work no more. ... But before taking the dash out I would like to know how to remove those .... Instrument cluster gear select blank screen solder fix Chevrolet GM ...

Repair the odometer/PRND321 LCD display on a '99-'06 ...

www.instructables.com/.../Repair-the-odometergear-select-L...

InstructablesIn this Instructable, I will show you how to repair odometer/gear select ... Repair the

Feb 09, 2016 | 1998 Chevrolet Blazer

2 Answers

How to remove rear bumper 1999 blazer


Hi there:
Check this Removal Procedure...

6_23_2012_11_21_59_pm.gif

1. Remove the rear bumper step pads.
2. Remove the license plate lamps.
3. Remove the nuts and the bolts that retain the rear bumper impact bar to the bumper bracket.
4. Remove the rear bumper impact bar from the vehicle.

Installation Procedure

6_23_2012_11_22_56_pm.gif

Notice: Refer to Fastener Notice in Service Precautions.

1. Install the rear bumper impact bar to the vehicle as follows:

1.1. Position the bumper impact bar on the bumper brackets so that the holes in the impact bar are aligned with the bracket holes.
1.2. Install 2 bolt plates and 4 nuts on top of the impact bar.
1.3. Install 2 bolt and nuts through the bottom of the impact bar. Tighten the rear bumper impact bar nuts to 90 N.m (66 lb ft).

2. Install the license plate lamps.
3. Install the rear bumper step pads.


Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 23, 2012 | 1999 Chevrolet Blazer

1 Answer

License plate lights on my 1999 chevy 4 door blazer dont work


hi u need 2 check bulbs if they ok check blown fuses if ok make sure lights have good earths

Sep 10, 2011 | 1999 Chevrolet Blazer

1 Answer

Change tag light bulb


  1. Remove two screws retaining the lamp to the rear license plate lamp shield.
  1. Rotate socket one quarter turn from backside of lamp and remove the miniature bulb (13466) .

  1. Install new miniature bulb into socket.
  1. Install socket in lamp .
  1. Secure lamp to rear license plate lamp shield with two screws and tighten to 2 Nm (18 lb-in).


    ak1473a.gif


    Item Part Number Description 1 13508 Rear License Plate Lamp Shield 2 14A583 Lamp Lead Wire 3 383356-S Nut (4 Req'd) 4 56000-S Screw (4 Req'd) 5 13550 Lamp (2 Req'd) 6 13466 Miniature Bulb (2 Req'd) A — Tighten to 2 Nm (18 Lb-In)

Feb 27, 2010 | 1998 Ford Windstar

1 Answer

1999 Dodge Neon rear license Plate bulb


LICENSE PLATE LAMP BULB
REMOVAL
  1. Remove screws attaching license plate lamp to rear bumper
  2. Remove lamp from bumper.
  3. Remove bulb socket from lamp.
  4. Pull bulb from socket.

INSTALLATION
  1. Install bulb into socket.
  2. Install bulb socket into lamp.
  3. Place lamp in position.
  4. Install screws attaching license plate lamp to rear bumper.

Oct 08, 2009 | 1999 Dodge Neon

1 Answer

No trunk light, trunk release, or back-up lights: Please help!


How can I adj. . a trunk light switch on a 02 Buick Century

Sep 26, 2009 | 1999 Buick Century

1 Answer

How do I change the rear license plate light bulbs?


License Plate Lights Removal & Installation License plate lamp retainer clips
a555c7b.gif
To Remove:
Remove or disconnect the following:
  1. License plate
  2. Pin-type retainers and the luggage compartment lid trim panel
  3. License plate lamp electrical connector
  4. Lamp socket from the license plate lamp
  5. Using a suitable tool, through the access hole, release the clips and remove the license plate lamp
To Install:
  1. Install or connect the following:
  2. License plate lamp
  3. Lamp socket to the license plate lamp
  4. Electrical connector
  5. Luggage compartment lid trim panel
  6. License plate

Jun 06, 2009 | 2000 Lincoln LS

1 Answer

I have a 1999 chev Blazer license plate lamps will not function and have been changed with known good parts.. All other exterior lights are fine


You will have to use a 12V test light to make sure you are getting power to the socket. If you are not, check fuses (not likely) then make sure the inside of the socket is clean. A broken wire may also be the problem if not getting power. The test light will help you pinpoint exactly where along the wire you have lost power. I'd check where the wire goes from the liftgate to the cab first to see if you have a pinched wire.

Nov 21, 2008 | 1999 Chevrolet Blazer

1 Answer

License plate lamp


Left side lamp, with some soft force you twist it clockwise. Reverse action to reinstall.
Right side lamp, twist it counterclockwise. Reverse action to reinstall

Jul 23, 2008 | 1999 Chevrolet Blazer

Not finding what you are looking for?
1999 Chevrolet Blazer Logo

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...