Question about 2005 Dodge Grand Caravan

2 Answers

2007 dodge grand caravan

I cant get the rear caliper off to change brake pads, have removed caliper mounting bolts but cannot locate mounting bracket bolt to remove and finish changing rear brake pads.... can u help?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Where are the bolts to remove the caliber on the rear brakes for a 2007 dodge caravan?

Posted on May 02, 2010

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 512 Answers

According to the service manual there are two bolts hold the caliber to tthe adapter plate and the caliper should roll up and out. the only problem i could imagine is if the pads are hanging in the adapter

Posted on Nov 22, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Trying to change the rear brakes on a 2008 caravan but can not get the e brake cable off so I can remove the caliper


The brake cable does not need to be removed to take off the caliper. The only things that need to be taken out are the two bolts that hold the caliper to its mounting bracket.

Hope this helps!

Jun 15, 2011 | 2008 Dodge Grand Caravan

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

Replacing brakes on a 2007 dodge grand caravan se


Front brakes are pretty easy, just go to http://www.customtacos.com/tech/index.php?article=37 for step-by-step instructions with pictures. On the bolts that it tells you to remove, it says they are 17mm, on the caravan they will take a 12mm socket to remove (at least on my 2007 short wheel base SE). The only issue I have with this site is it does not tell you how to remove rotors, and I NEVER replace brake pads without having my rotors turned or replaced. after you have swung the caliper up like the instructions on the website tell you to, you'll notice the rotors are still held in place by the caliper mounting bracket. It is held on with two large bolts that bolt in from the back. If I remember right, they are a 3/4" or 19mm socket. If they've been on for a while (my first brake change was at 48,000 miles) then you will need WD40, a big socket wrench, and a lot of elbow grease to get those loose. Once that's free, you can easily remove the rotors. I would take them to Checker or another local auto parts store that turns rotors, they will let you know if they can be turned or if they need to be replaced. If you get new rotors, don't forget to clean them off with brake cleaner before installing them!!! They are coated with an anti-rust chemical that is very sticky and will smoke for miles and affect your braking. For rear brakes (assuming they are drums, if not, they will be the same as the front), there is a pretty good tutorial at http://trashcars.net/videos/1436/how-to-replace-rear-drum-brakes.html. You should also have your drums turned or replaced when you replace the rear brake shoes as well.

Nov 06, 2010 | 2007 Dodge Caravan SXT Minivan New Cars

1 Answer

How do you replace the front and rear brakes in a 2003 pontiac Grand Prix


Removal & Installation Front To Remove:
  1. Inspect the fluid level in the master cylinder reservoir. Remove fluid from the reservoir until the level is lower then half way between the MAX and MIN levels.
  2. Remove the tire and wheel assembly.
  3. Install 2 wheel nuts to secure the rotor on the hub.
  4. Remove the bottom brake caliper pin bolt.
  5. Pivot the brake caliper body upward and secure out of the way. Do NOT disconnect the hydraulic brake flexible hose from the caliper.
  6. Compress the piston back into the bore using a C-clamp. Figure of brake assembly with caliper raised showing brake pads in mounting bracket gmpc_l4.gif

  7. Remove the inboard and outboard brake pads from the brake caliper bracket.
To Install:
  1. Install the brake pad retainers and both brake pads into the caliper bracket.
  2. Pivot the brake caliper down over the brake pads and into the brake caliper bracket. Insert the lower brake caliper pin bolt and torque bolt to 70 ft-lb. (95 Nm).
  3. Reinstall the tire and wheel assembly.
  4. Lower the vehicle.
  5. Refill the master cylinder. Pump the brake pedal several times to seat the pads against the rotor.
  6. Check the master cylinder level and add fluid as necessary.
Rear To Remove:
Rear disc pads R&I gm-09-00-492.gif

  1. Inspect the fluid level in the master cylinder reservoir. Remove fluid from the reservoir until the level is lower then half way between the MAX and MIN levels.
  2. Remove the tire and wheel assembly.
  3. Install 2 wheel nuts to secure the rotor on the hub.
  4. Remove the upper caliper mounting bolt.
  5. Pivot the caliper down to access the pads.
  6. Remove the inboard and outboard pads from the caliper bracket.
  7. Remove the brake pad clips from the caliper bracket.
  8. Compress the piston back into the bore using a C-clamp and the old inner pad.
To Install:
  1. Install new brake clips in the caliper bracket.
  2. Install the inboard and outboard pads in the caliper bracket.
  3. Pivot the caliper up over the pads.
  4. Reinstall the upper mounting bolt and tighten to 32 ft. lbs. (44 Nm).
  5. Remove the 2 wheel nuts securing the rotor.
  6. Reinstall the tire and wheel assembly.
  7. Refill the master cylinder. Pump the brake pedal several times to seat the pads against the rotor.
  8. Check the master cylinder level and add fluid as necessary.
prev.gif next.gif

Aug 26, 2010 | 2003 Pontiac Grand Prix

1 Answer

How to change front brake pads on 2003 Chevy Suburban


Disc Brake Pads for Suburban 1500 Removal & Installation Front To Remove:
Front caliper mounting bracket 93086g95.gif

  1. Remove the cover on the master cylinder and siphon out 2/3 of the fluid. This step prevents spilling fluid when the piston is pushed back into the caliper bore.
  2. Raise and support the vehicle safely.
  3. Remove the wheel and tire assembly.
  4. Compress the brake piston back into its bore using a C-clamp.
  5. Remove the 2 caliper mounting bolts. Lift the caliper off the rotor.
  6. Remove the inboard and outboard pad.
  7. Remove and discard the anti-rattle clips.
To Install:
Caliper bracket sleeves 93086g97.gif

  1. Thoroughly inspect, clean and lubricate all caliper slide points, bolts and hardware.
  2. Install new anti-rattle clips.
  3. Position the inboard and outboard pads into the support bracket
  4. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
  5. Install the caliper mounting bolts through the sleeves in the inboard caliper ears and into the mounting bracket.
  6. Tighten the mounting bolts to: 80 lb. ft, (110 Nm).
  7. Install the tire and wheel assembly. Lower the vehicle.
  8. Add fluid to the master cylinder reservoirs so they are 1/4 in. (6.35mm) from the top.
  9. Test the brake pedal by pumping it to obtain a hard pedal. Check the fluid level and add fluid as necessary.
Rear To Remove:
  1. Remove 2/3 of the brake fluid from the master cylinder.
  2. Raise and safely support the vehicle.
  3. Remove the wheel and tire assembly.
  4. Remove the brake caliper mounting bolts. Suspend the caliper from the frame with mechanic's wire. Do not allow the caliper to hang from the brake hose.
  5. Remove the brake pads from the caliper mounting bracket.
  6. Remove and discard the anti-rattle clips.
Rear brake caliper 93086g96.gif

To Install:
  1. Install new anti-rattle clips.
  2. Position the brake pads to the caliper mounting bracket.
  3. With the 2 pads in position, place the caliper over the brake rotor and align the holes in the caliper with those of the mounting bracket.
  4. Install NEW caliper mounting bolts. Tighten to: 30 lb. ft, (40 Nm).
  5. Install the wheel and tire assembly.
  6. Lower the vehicle.
  7. Refill the master cylinder to the proper level with fresh brake fluid. Pump the brake pedal slowly and firmly to seat the brake pads. Burnish the brakes as needed.
prev.gif next.gif

Jul 05, 2010 | 2004 Chevrolet Suburban

3 Answers

How do i change the brake pads on a 2005 grand prix pontiac


remove the caliper, by removing the two holding bolts, then use a old brake pad against the pistons and a c clamp and push piston all the way in, next is to clean and lube pad mounting surface and the caliper slide pin, then install new pads on bracket then caliper and tighten caliper bolts, heres a diagram to help you,98c6b31.jpg150490f.jpg

Apr 16, 2010 | 2005 Pontiac Grand Prix

1 Answer

How do i get the calapers off the rear of a 2006 grand caravane?


Using a C clamp depress the claiper. There a spot right in the middle to do this. Now the fun part hope you have metic hex key set. The 2 caliper guide pins are on the back inside the boots. Which need to be in great condition. Using the metic hex keys some are 7mm or 8mm turn to your right to remove. Rmove the caliper mounting bracket bolts. Fun part #2 removing the disc rotor. Theres parking brake pads or a durm brake system on the inside of the rotor. If the rotor does not slide off. You must remove the rubber gromet on the back of the backing plate. Using a screwdriver or the old brake adjuster tool turn the star wheel to adjust the parking brake in to remove the disc rotor. All brake guides on the calipers & guide pins need to have high temperture brake grease applyed to them. Buy the big bottle for $10 for the front brakes & future use it comes with a bush. Note ** Remove a guide pin take to auto store buy socket to reinstall guide pin/bolt. Why Caliper guide pins 26lbs torque. Caliper mounting bolts 125lb torque

Dec 05, 2009 | 2006 Dodge Grand Caravan

1 Answer

Silverado 1500 Z71 off road, 5.3L. Details on fr


This is for the front: Removal & Installation
  1. Remove 2/3 of the brake fluid from the master cylinder.
  2. Remove or disconnect the following:
    • Wheel
    • Caliper. Suspend the caliper from the frame with mechanic's wire. Do not allow the caliper to hang from the brake hose.
    • Caliper mounting bracket bolts
    • Caliper mounting bracket from the steering knuckle assembly
    • Brake pads from the caliper mounting bracket
    • Clips from the inside ends of the caliper mounting bracket and discard
To install:
  1. Install or connect the following:
    • Clips to the inside ends of the caliper mounting bracket
    • Brake pads to the caliper mounting bracket
    • Inner pad (1 wear indicator)
    • Outer pad (2 wear indicators)
    • Caliper mounting bracket to the steering knuckle assembly
  2. Perform the following procedure before installing the caliper mounting bracket bolts:
    • Remove all traces of the original adhesive patch.
    • Clean the threads of the bolt with brake parts cleaner or the equivalent and allow to dry.
    • Apply red Loctite®272 to the threads of the bolt.
  3. Install or connect the following:
    • Caliper mounting bracket bolts to the steering knuckle. Tighten the caliper guide pin bolts to 74 ft. lbs. (100 Nm) on 15 series or 80 ft. lbs. (108 Nm) on 25/35 series.
    • Caliper
    • Tire and wheel assembly
  4. Refill the master cylinder to the proper level with fresh brake fluid. Pump the brake pedal slowly and firmly in order to seat the brake pads. Burnish the brakes as needed.

Oct 12, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

DESCRIBE CHANGE OUT OF PADS AND ROTORS FOR A 2007 DODGE GRAND CARAVAN 2007


first raise and safely support vehicle remove the wheels remove the spring from the caliper(pry under the spring where it goes into the caliper be careful don't let it fly) locate the two torx bolts holding the caliper to the bracket remove them using the proper size bit remove the caliper by prying it away from the bracket remove the pads by pulling strait out remove the two bolts holding the bracket to the steering knukle(very tight) remove the rotor install is the reverse of removal torque specs are as follows wheels 80-100ftlbs caliper bolts 40ftlbs bracket bolts 90 ftlbs



Sep 24, 2009 | 2007 Dodge Grand Caravan SXT Minivan

2 Answers

Changing Rear brake pads 2005 dodge grand caravan


There are 2 bolts on the "inside" on the caliper towards the bottom they use an allen wrench socket.

May 13, 2009 | 2002 Dodge Grand Caravan

Not finding what you are looking for?
2005 Dodge Grand Caravan Logo

922 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...