Question about 2006 Dodge Dakota

1 Answer

Change key tumbler

2001 Dodge Dakota Quad column shifter. I need to change key tumbler.
What is the process I should follow?

Posted by on

  • Anonymous Mar 24, 2014

    replace key tumbler 88 ram

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

  • Expert
  • 185 Answers

My honest opinion here would be to goto your local auto parts store and buy the Haynes Manual for your truck. It cost about 15 bucks, and it gives you very precise procedures that will help you out quite a bit.

Sincerely,

JC

Posted on Nov 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The gear shifter cable broke off the top end of column shifter does the whole cable need changing or no 2003 dodge Dakota automatic


gear shifter cable broke Anon, Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."

Replacing shift cable couple questions DodgeForum com

shifting cable from steering column not moving the transmission shift...

Fix Your Dodge With Your Own Hands

Fix Your Dodge With Your Own Hands

denlorstools com

Apr 05, 2016 | Dodge Cars & Trucks

1 Answer

02 dodge dakota sport 4x4 auto quad cab 4.7L starts up but then dies as if key was turned off within seconds of starting


Possible distributor cap cracked? Possible short in the ignition system? Fuel Filter clogged? Fuel Pump not producing enough pressure to keep it running? Shifter linkage broken? Is there a Check Engine Light On? More details needed.

Apr 15, 2014 | 2002 Dodge Dakota Club Cab

1 Answer

2001 dodge stratus. left turn signal turns on 4 way blinkers?


I believe the problem is in turn signal/flasher control near the top of steering column. follow the link for a video that close to the exact procedure you will need to follow.

Apr 07, 2014 | 2001 Dodge Dakota

1 Answer

PLUG WIRE ORDER ON THE DISTRIBUTOR CAP FOR A 2001 DODGE DAKOTA QUAD CAB 3.9L V6


From the 2001 Dodge Dakota maintenance manual.
Note the numbering of the 6 cylinders and the arrow indicating front of engine.
Firing order: 1-6-5-4-3-2, with distributor rotating clockwise.


archaeology_30.jpg

Mar 15, 2011 | 2001 Dodge Dakota

1 Answer

How do i remove the steering column cover to get at the ignition tumbler on a 1993 dodge dakota


CAUTION Disconnect and isolate the negative (ground) battery cable. This will disable the air bag system. Failure to disconnect the battery could result in accidental deployment and possible personal injury. Allow the system capacitor to discharge for two minutes then begin air bag system component removal. To install:
  1. Engage the electrical connectors to the ignition switch and make sure the switch locking tabs are fully seated.
  2. Before attaching the ignition switch to a tilt steering column, the transmission shifter must be in the PARK position. Also the park lock dowel pin and the column lock flag must be properly indexed before installing the switch as follows:
    1. Place the transmission shifter in the PARK position
    2. Place the ignition switch in the LOCK position. The switch is in the lock position when the column lock flag is parallel to the ignition switch terminals.
    3. Position the ignition switch park lock dowel pin so it will engage the steering column park lock slider linkage.
    4. Apply a light coating of grease to the column lock flag and the park lock dowel pin.
  3. Place the ignition switch against the lock housing opening on the steering column. Ensure that the ignition switch park lock dowel pin enters the slot in the park lock slider linkage in the steering column.
  4. Install the retaining bracket and ignition switch mounting screws, then tighten the screws to 22-30 inch lbs. (3-4 Nm).
  5. If the vehicle is equipped with a tilt steering column, install the tilt lever.
  6. With the key cylinder and the ignition switch in the LOCK position, insert the key cylinder into the ignition switch until it bottoms.
  7. Insert the ignition key into the lock cylinder. While pushing the key cylinder in toward the ignition switch, rotate the ignition key until the end of travel.
  8. Install the retaining screw into the bracket and lock cylinder. Tighten the screw to 22-30 inch lbs. (3-4 Nm).
  9. Install the steering column covers, then the tilt lever, if equipped.
  10. Connect the negative battery cable.
  11. Check for proper operation.


ec3f7ac.jpg

eff2c5f.jpg

72e2667.jpg

7a1362b.jpg

Jul 30, 2010 | 1993 Dodge Dakota

1 Answer

How to change gear shift cable on 2001 dodge dakota 2 wheel drive


the cable goes from the shifter to the transmittion arm,, both cable ends connect via a pin and cotter key (usually) the cable housing (black outside layer) is connected to the shifter frame usaually by a clip and is bolted to the transmittion with a couple bolts on the other end ,, i know this was pertty basic but hope it helped

Mar 28, 2010 | 2001 Dodge Dakota

1 Answer

How to replace a ignition switch in 2001 dodge dakata


Remove the cover over the steering column. Then it is a simple matter of inserting a screwdriver to depress a locking tab while pulling the old ignition tumbler straight out using the key as a handle. Then just insert the new one...easy peasy!

Jul 02, 2009 | 2001 Dodge Dakota

Not finding what you are looking for?
2006 Dodge Dakota Logo

Related Topics:

95 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...