Question about 1999 Mitsubishi Eclipse

1 Answer

Front and rear motor mounts bad 99 mitsubitshi eclipse gs 2.0L AT

What is procedure for the rear mount change

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 98 Answers

Just jack up and remove the driverside motor, just put a piece of lumber between the jack and oilpan, then raise up alittle unbolt front and rear motor mounts should come out easy, then replace and drop engine back into place, its alot easier than one would think, good luck

Posted on Dec 10, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Too much vibration on startup


No harm will come from slightly overfilling the engine with oil. It doesn't cause leaks as most people THINK. The engine does not build up pressure inside because of the PCV system that draws crankcase vapors into the intake to be burned. You have another problem keeping your car from cranking. Possibly a bad starter, solenoid switch or even bad wiring.


----------------------------obd2express.co.uk
http://www.obd2express.co.uk/wholesale/new-design-autocom-cdp-for-cars-trucks-and-obd2.html

Nov 24, 2012 | 2003 Mitsubishi Eclipse Coupe

1 Answer

Location of rear motor mount


Need to know what vehicle? Most rear mounts are located on top of rear strut, if it is a front wheel drive. The rear strut would have to be removed for replacement. Most of newer mounts require specialty tools and can be dangerous if you do not know proper procedure for changing them.

Nov 21, 2012 | Cars & Trucks

1 Answer

I have a 2003 mitsubishi eclipse spider, how to change the spart plugs


i'm guessing you're asking because it's a v6 FWD and you don't know how to get to the spark plugs along the firewall. you will need to find the front motor mounts or the anti torque bolts whatever you wanna call it and make your motor swing. you can do that by locating your front motor mounts or side or even rear. i'm not sure with a eclipse but once you've found the anti torque bolts attached to it and removed them you can roll the car forward and it should leave about 6 inches of space behind the engine to get the those spark plugs. front should be easy

Mar 01, 2010 | 2003 Mitsubishi Eclipse Spyder

1 Answer

Where is the map sensor located at on a 96 eclipse gs no turbo


Under hood, center, front engine area, mounted on driver side lower front of engine

Jan 25, 2010 | 1995 Mitsubishi Eclipse

1 Answer

My 2002 eclipse vibrates vigorously at a stop or idle... have serviced, tuned, etc etc. please help


The motor mounts are common failure points on these cars.

In particular, the transmission hanger mount and rear rollstopper mount are the worst for failure rates.

The front rollstopper is 3rd most common, and the front engine mount is least likely to fail (rare).

The mounts range from 75-125 each and require about 2.5 hours to change all four. As I said before, the front engine mount is very unlikely to need replacement though, the other 3 are likely the only ones you will see damage on.once they are removed.

Oct 16, 2009 | Mitsubishi Eclipse Cars & Trucks

1 Answer

How can i replace it?


http://autos.groups.yahoo.com/group/villagerquest/

it's usually called the trans mount cause that's what's on that side.

Section 02-03: Engine and Transaxle Mounting 1997 Villager Workshop Manual
REMOVAL AND INSTALLATION Support Insulator, Front Transaxle Removal
  1. Remove the battery (10655). Refer to Section 14-01 for the removal procedure.
  2. Remove the Engine Air Cleaner (ACL) (9600). Refer to Section 03-12 for the removal procedure.
  3. Remove the radiator coolant recovery reservoir (8A080). Refer to Section 03-03 for the removal procedure.
  4. Remove the battery tray (10732). Refer to Section 14-01 for the removal procedure.
  5. Support the transaxle with a floor jack.
  6. Remove the front transaxle support insulator through bolt and nut.
  7. Remove the three front transaxle support insulator bolts and the front transaxle support insulator.
-----------------------------------------------------------
Support Insulator, Rear Transaxle Removal
  1. Remove the rear transaxle support bracket. Refer to the procedure in this section.
  1. Raise and support the vehicle.
  1. Remove the three rear transaxle support insulator nuts.




  1. Lower the vehicle.
  1. Remove the rear transaxle support insulator from the vehicle.

Mar 29, 2009 | 1997 Mercury Villager

1 Answer

Front plate in a mitsubishi eclipse


If your State doesn't require it, why install it?
If your State does require a front plate, and you just bought the car, take it back to the dealer. They are required by law to install the plate before selling it.

Any auto store can sell you mounting hardware for your front plate. If you look at your front bumper, you should see two little dimples in the center of the bumper, these will line up with your plateholder. Make sure it does and drill there, and mount with proper hardware.

Jan 13, 2009 | 2007 Mitsubishi Eclipse

2 Answers

Front and rear motor mounts bad on 99 mitsubishi eclipse automatic whats the best procedure for replacement


just put the jack under the engine with a board in between the oil pan and jack, raise up a little unbolt the mount, jack up more, you might have to loosen other motor mounts but you should be able to squeeze out the mounts with ease or a little prying of a pry bar, its much simpler then most would think, just did it on 2 awd turbo eclipses last week, you can also buy a polly urithane kit and knock out the guts of the mounts and replace with the pollys for pretty cheap. im in iowa if you need help let me know.

Dec 02, 2008 | Mitsubishi Eclipse Cars & Trucks

1 Answer

Motor mount


Yes this mount supports a lot of the motor. It also supports the transmission so if you are on a down hill slope the motor will roll forward and cause a lot of pressure on the front mount. Hope this helps.

Aug 10, 2008 | 1999 Pontiac Grand Am GT

Not finding what you are looking for?
1999 Mitsubishi Eclipse Logo

1,229 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...