Question about 1997 Chrysler Sebring

1 Answer

Speed sensor Where is the speed sensor located on a 98 chrysler sebring and how many speed sensors does it have?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Chrysler Expert
  • 293 Answers

It has an input and an output spped sensor located on the front side of the transaxle

Posted on Nov 20, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 96 Chrysler Sebring. I replaced input n output sensors on tranny. My speedometer still doesn't work. Is there a cable from speedometer to tranny


if you have done all the above and the sensors and wires are good give these guys a shout, they maybe able to help

southernelectronics.com

Apr 09, 2015 | 1996 Chrysler Sebring

1 Answer

Peed sensors on my 2002 chrysler sebring lxi 2.7 liter convertable


convertibles are just a regular car with a different roof

Sep 24, 2017 | 2002 Chrysler Sebring

1 Answer

2004 Chrysler Sebring Sebring transmission speed sensor


there is a input and output speed sensor on the trans

Jan 18, 2012 | 2004 Chrysler Sebring

1 Answer

Sebring 1997 I need picture to lookat the PCM sensor and the Crankshaft position sensor (CKP sensor)


On 1997 Chrysler Sebring 2.5L MFI 6cyl...
- the PCM is located in the left side of the engine compartment, beside the Power Distribution Center (PDC).

zjlimited_767.gif

Fig. 1: Location of the PCM on the Cirrus, Stratus, Sebring convertible and Breeze models

zjlimited_768.gif

Fig. 2: Location of the PCM on the Sebring coupe and Avenger models

- the Crankshaft Position Sensor is located: under hood, driver side, upper engine area, mounted on end of engine block

zjlimited_769.gif

Fig. 4: Location of the crankshaft position sensor on 2.5L engines

Hope helps; remember to rating this answer and leave some testimonial comments.

Oct 09, 2011 | 1997 Chrysler Sebring

1 Answer

1998 Chrysler Sebring convertible Not shifting into drive check engine light came on, error code PO715


DTC P0715 CHRYSLER - Input Speed Sensor 1 Circuit
P0715 is detected when TCM or ECM does not receive the proper signal from the sensor.

The input speed sensor detects the primary pulley revolution speed and sends a signal to the Transmission Control Module (TCM) and Engine Control Module (ECM).

Symptoms
- Engine Light ON (or Service Engine Soon Warning Light)
- Possible shifting problems

Possible causes
- Transmission speed sensor circuit is open or shorted.
- Poor transmission speed sensor circuit connection
- Faulty transmission speed sensor

Hope this clues helps to solve it.

Jun 02, 2011 | 2003 Chrysler Sebring

1 Answer

Where is the speed sensor located on a 2004 chrysler sebring convertible???


The speed sensors are on the side of the trans that faces the front of the car. They are about midline height, with one of them near the seam between the engine and the transmission, and the other near the very far end of the transmission, basically on either side of the vertical shift rod. They simply unscrew, after lifting tab and removing the electrical plug, and screw back in to about the torque of a spark plug. They look very similar to one another.

May 17, 2011 | 2004 Chrysler Sebring

2 Answers

98 chrysler sebring 2.5 v 6 crankshaft sensor location


driver side rear of engine on top in tranny has a 10mm bolt holding it

Jan 17, 2010 | 1999 Chrysler Sebring

2 Answers

2003 chrysler sebring is hesitating whn at higher


(Fuel filter will not effect anything, it only prevents build up in engine)
Could be one of these-
Oxygen sensor
fuel sensor
Dirty injectors
Bad injector/injectors

~~~~Go to car zone/ or a frendly auto part store, and ask them for a FREE electronic computer check ( where they check the computer, and the computer tell them whats wrong)

Sep 28, 2009 | 2003 Chrysler Sebring

3 Answers

98 sebring O2 sensor location


what engine, is it the O2 sensor or the cat sensor, do u have the trouble code.

Sep 17, 2009 | 1998 Chrysler Sebring

1 Answer

98 sebring


check the cable at ecm if it is pulled to tight up or down this will put stress on the pins and result in a car that runs like it needs a tuneup

Nov 09, 2017 | 1998 Chrysler Sebring

Not finding what you are looking for?
1997 Chrysler Sebring Logo

Related Topics:

524 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

81400 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...