Question about 1994 Dodge Caravan

1 Answer

How do I remove the timing belt cover on a 1994 Dodge caravan 2.5 liter engine

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 1,975 Answers

Below are some instructions that I hope will help. Just a hint as far as installing the belt. Before you do the final torque or the belt tensioner, you should rotate the engine (by hand) 2 revolutions to TDC and double check all your marks before puting the cover back on.



How do I remove the timing belt cover on a 1994 - 5_8_2012_9_59_30_am.jpg5_8_2012_9_59_51_am.jpgHow do I remove the timing belt cover on a 1994 - 5_8_2012_10_00_24_am.jpg><img src=

Posted on May 08, 2012

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: how to replace serpentine belt?

how to remove and re-install serpentine belt?

Posted on Nov 20, 2008

motor1258
  • 6674 Answers

SOURCE: belt diagram 2004 5.7 liter engine dodge ram 1500 1/2 ton 4x4

click on this link, and scroll down to 5.7L

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800ba71e

Posted on Dec 22, 2008

  • 323 Answers

SOURCE: timing belt or chain

The 3.3 and 3.8 use a chain.

Posted on Apr 26, 2009

  • 1757 Answers

SOURCE: Need serpentine belt routing diagram for 1994 Dodge grand caravan

3.3L?
Looking at the engine from front (right side of the Van): Stating at the Top, Going Left to Right and Clockwise:
Over the Alternator
To under the Idle Pulley,
To Over the AC Compressor.
To the Left Side of the Water Pump.
To the Right side and Under the Crankshaft Pulley
To the Right side and Over and Down the Tensioner
To Under the Power Steering Pump
And Back up-to the Left side of the Alternator.
Advise when puting it on:
Put the Belt around everything else accept for the Alternator. After it is around all the rest of the Pulleys - Pull the belt up - tight from the Power steering Pump and the Idle Pulley to form a loop, holding the Belt close to the Altenator Pulley.
Using the 15mm wrench or belt tensioner bar - rotate the Tensioner Pulley towards the front of the Van and then place the belt over the Alternator.
Let me know if this helped or if you have additional information or questions. Feel free to contact me at FixYa.com!

Posted on Jan 22, 2010

johnjohn2
  • 5763 Answers

SOURCE: i need the belt diagram for a 3.3 liter V6 1994

Heres a belt diagram for your 1994 dodge grand caravan with a 3.3 engine, hope this helpful.1312666.gif

Posted on Jun 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to install a timing belt on a 2.2 1990 dodge shadow


A lot of work. You will need to remove an engine mount, all plastic covers, turn the engine so that all timing marks line up with the little marks on the engine. Release the tension on the timing belt, remove the belt, put the new belt on, let the tension go back onto the belt, ensure that neither cam has moved away from the mark. Ensure that the crankshaft is still on the mark, then reassemble the outer covers, install the serpentine belt and the mount. Please go to the internet and search for videos and pictures. Pictures tell a thousand words. Here is a link. Replacing Chrysler 2 2 and 2 5 liter engine timing belts

Dec 10, 2017 | Dodge Cars & Trucks

2 Answers

How do I time a 1994 dodge caravan 3 0L Problem PLEAS IF ANY ONE HAVE THE DIGRAM


Is this what you needed?

jturcotte_1784.gif

Fig. Fig. 14: Sprocket timing for belt installation-3.0L engines


0900c15280215dd8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 15: Secure the sprocket when removing or installing the nut-3.0L engines


0900c15280215dd9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 16: Timing belt tensioner-3.0L engines


0900c15280215dda.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 17: Positioning the tensioner-3.0L engines
The timing belt can be inspected by removing the upper (front outer) timing cover.

  1. Disconnect the negative battery cable.
  2. Remove the accessory drive belts.
  3. Remove the timing belt covers.
  4. Identify the timing belt running direction to avoid reversal during installation.
  5. Loosen timing belt tensioner bolt and remove timing belt.
  6. Remove the crankshaft sprocket flange.

To install:
  1. Rotate the crankshaft sprocket until timing mark on crankshaft sprocket is lined up with the oil pump timing mark at 1 o'clock position.
  2. Rotate the (inner) camshaft sprocket until mark on (inner) camshaft sprocket is lined up with the timing mark on alternator bracket.
  3. Rotate the (outer) camshaft sprocket (radiator side) until mark on the sprocket is lined up with the timing mark on the timing belt inner cover. Refer to timing belt illustration.
  4. Install the timing belt on the crankshaft sprocket while maintaining pressure on the tensioner side.
  5. Position the timing belt over the camshaft sprocket (radiator side). Next, position the belt under the water pump pulley, then over the (inner) sprocket and finally over the tensioner.
  6. Apply rotating force in the opposite direction to the camshaft sprocket (radiator side) to create tension on the timing belt tension side.
  7. Rotate the crankshaft in a clockwise direction and recheck engine timing marks.
  8. Install the crankshaft sprocket flange.
  9. Loosen the tensioner bolt and allow tensioner spring to tension the belt.
  10. Again rotate the crankshaft in a clockwise direction (2) full turns. Recheck the engine timing. Tighten the tensioner bolt to 23 ft. lbs. (31 Nm).
  11. Install the timing covers.
  12. Install the accessory drive belts.
  13. Connect battery negative cable.

May 29, 2011 | Dodge Caravan Cars & Trucks

1 Answer

How long and easy is it to rebuild oil pump on 94 grand caravan 3.8l


Don't bother. Replace the unit.
3.0 liter
The oil pump assembly used on this engine is mounted at the front of the crankshaft. The oil pump also retains the crankshaft front oil seal.
  1. Remove the accessory drive belts.
  2. Remove the timing belt cover and timing belt. Refer to the timing belt removal and installation procedures in this section.
  3. Remove the crankshaft sprocket.
  4. Remove the oil pump mounting bolts (5), and remove oil pump assembly. Mark mounting bolts for proper installation during reassembly.

To install:
  1. Clean the oil pump and engine block gasket surfaces thoroughly.
  2. Position a new gasket on pump assembly and install on cylinder block. Make sure correct length bolts are in proper locations and tighten all bolts to 10 ft. lbs. (14 Nm).
  3. Install the crankshaft sprocket and timing belt. Recheck engine timing marks.
  4. Install the timing belt covers. For more details, refer to the timing belt cover installation procedures.
  5. Install the accessory drive belts.
  6. Refill the crankcase and start the engine.
  7. Check for correct engine oil pressure and for any oil leakage.
3.3 and 3.8 liter engines


  1. Disconnect the negative battery cable. Remove the dipstick.
  2. Raise the vehicle and support safely. Drain the oil and remove the oil pan.
  3. Remove the oil pickup.
  4. Remove the chain case cover.
  5. Disassemble the oil pump as required.

To install:
  1. Assemble the pump. Tighten the cover screws to 10 ft. lbs. (14 Nm).
  2. Prime the oil pump by filling the rotor cavity with fresh oil and turning the rotors until oil comes out the pressure port. Repeat a few times until no air bubbles are present.
  3. Install the chain case cover.
  4. Clean out the oil pickup or replace as required. Replace the oil pickup O-ring and install the pickup to the pump.
  5. Install the oil pan.
  6. Install the dipstick. Fill the engine with the proper amount of oil.
  7. Connect the negative battery cable and check the oil pressure. Check for any oil leaks.
for the 3.3 you can rebuild, 3.0 - replace.

Feb 15, 2011 | 1994 Dodge Caravan

1 Answer

How do i change the water pump on a 2000 dodge,grand caravan


Removing and changing the water pump on a 2000 Grand Caravan should only be done if your van has a 3.3 liter or 3.8 liter V6 engine. On any other engine types, including four-cylinder engines, you must remove the timing belt from the engine to access the water pump, which is a dangerous task that can mess up the engine if attempted by an amateur.
The procedure is as follows:------------- The water pump is responsible for sending the engine coolant to the engine.First of all remove the serpentine belt then remove the plastic cove on the passenger side behind the wheel. You will have to remove the pulley. Once the pulley is removed unbolt the water pump and remove it. Clean the surfaces and install new pump. Draining the coolant and replacing it is advisable.
Drain the engine coolant, twisting and removing the drain plug at the bottom of the radiator
-------------------Thats it.

Nov 18, 2010 | 2000 Dodge Caravan

1 Answer

How do I tell if I've got a broken timing belt? It's in a 1996 Dodge Caravan was driving it and it started to kinda chug then just died.


Easiest way would be to peek into the valve cover thru oil fill cap or PCV port and look for valves to move when engine cranks. This would not tell you if it just slipped though. You will have to remove the timing cover to tell if the timing is just off a tooth or 2. If you have overhead cam (and I think you do), you may be able to just take off the upper timing belt covers. Turn the engine to TDC and check the timing marks per below pics

2.4L engine:

2fffec1.gif
3.0L engine


aa0c80e.gif

Oct 01, 2010 | 1996 Dodge Caravan

1 Answer

Do 1994 dodge caravans have crank senoers?


YES IT DOES ***.2.5L ENGINE CKP SENSOR LOCATED UNDER THE DISTRIBUTOR NEAR THE TRANSAXLE BELL HOUSING.*** ENGINES 3.0L 3.8L CKP SENSOR LOCATED IN THE TIMING BELT COVER.

Sep 09, 2010 | 1994 Dodge Caravan

1 Answer

I need the belt diagram for a 3.0 liter v6 1994


cb71570.jpg

Fig. 14: Sprocket timing for belt installation-3.0L engines

Jun 08, 2010 | 1994 Dodge Grand Caravan

2 Answers

I need the belt diagram for a 3.3 liter V6 1994 dodge grand caravan le


Heres a belt diagram for your 1994 dodge grand caravan with a 3.3 engine, hope this helpful.1312666.gif

Jun 01, 2010 | 1994 Dodge Grand Caravan

2 Answers

Is the water pump on a 96 grand caravan 3.3L run by the timeing belt


Good morning! The water pump on this model is not run by the timing belt. The 3.3 liter engine uses a timing chain. Hope you find this information useful!

Nov 11, 2009 | 1996 Dodge Caravan

3 Answers

How do you change the timing belt on a 1994 dodge grand caravan with a 3.0 Liter Eng.


If this is the 3.0L double overhead cam chrysler engine it is more complicated than some of the others, After disconnecting the battery, set the timing to number one cylinder cause alignment of timing belt is critical. you have to remove all the drive belts, the a/c stuffk, the alternator, power steering stuff, ac bracket, belt tensioner, all that stuff in front of engine cause you have to remove timing cover. you need to remember where everything goes back... After you get the power steering and all that other stuff off, your next thing is to remove the crankshaft pulleys and front engine mount. Then you have to remove all the upper and lower timing belt covers & keep track of where the fastners go. Then of course you have ato losen the timing belt tensioner bolt, belt & crankshaft flange shield. Do not let the cam sprockets move, make something to hold them or buy the tool. instillation,reverse of above, timing belt tensioner counterclockwise, tighten so tht you can put belt on... belt on crank pully first, etc. timing marks on cams are triangle with scribe mark on engine block; on crank it lines up with mark on oil pump... rotate engine a few turns after installing belt so that marks line up every time again, so that you dont have to take it apart. now put all the accessory and so forth stuff back on... This is probably an all day job... Hope this helps you, Rick

Apr 27, 2009 | 1994 Dodge Grand Caravan

Not finding what you are looking for?
1994 Dodge Caravan Logo

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

83850 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...