Question about 2000 Jeep Grand Cherokee

1 Answer

Pwertech inline six

To my understanding my truck has 3.73 gears in the rear..will i have to change them

Posted by on

  • daddy_phat_s Nov 22, 2008

    one more question if you dont mind?...... first of all u have been very helpful and i apreciate it. what about the transmission what should i do to it...just have the fluid changed and leave it at that....or what do you suggest....just doing my homework

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 242 Answers

You should not have to change any of your gears unless they are stripped. As long as you don't hear something that sounds like when you put your finger in a fan blade, it should be fine.

Posted on Nov 21, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want to replace5.4L in my 03 f150 with a non triton engine ..what can i use? is there a 4.7L i want to do away with triton engine...could i put inline 6 in it?


the major problem with fitting different engines is the transmission housing compatibility
if the bolt pattern is different, the cost of obtaining an adaptor plate makes the different engine fitment expensive
there is a technical division in ford motor company that you can contact for advice and they will be able to advise which engines have the same bolt patterns that will allow the change over
of course the other method is to change the engine / transmission as an assembly so if you want to put a inline six in use the inline six transmission as well

Dec 11, 2016 | 2003 Ford F-150

1 Answer

Need to change head gasket on 2007 chevrolet trailblazer with 4.2 inline six


if you need advise to do ,don't seek help from a expert or some one
that can personally help you, this is a major job,

Mar 27, 2014 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

If timeing gear goes bad will the valvs be hit by the piston


Niether the 4.0 inline six or either of the v-8s are interference motors.The pistons will not contact the valves.

Feb 19, 2011 | 1995 Jeep Grand Cherokee

1 Answer

My 81 f100 inline six Runs rough at idle while under load. i have the idle high in park, but damn near stalls when I put in gear or stop at a light.


have you given it a tune up latley? is it carb ot throttle body. check distributer cap inside for corrosion or moisture. fuel filter another possibility

Jan 30, 2011 | 1981 Ford F 100

1 Answer

What is the sparkplug gap for the 2002 jeep grand cherokee inline six cylinder


on four cylinders and inline sixes the gap is .035 as reccomended. but if the plugs are platinim, do not try to reset for they are set at factory. have a good day !!

Jan 08, 2011 | 2002 Jeep Grand Cherokee

2 Answers

When i start in the morning,the engine won't idle and when i drive,gear change is very,very slow.wen it warms up its OK, I have a 1996 toyota royal crown with a 3l, six cly inline, petrol engine


Change a sensor for fuel mixture preparation.Also colled ECT /engine coolant temperature/sensor.There is two sensors-one is for fuel gauge on an instrument panel-change another.

Dec 08, 2009 | 1996 Toyota Avalon

1 Answer

2004 avalance chevy


When was the last time you checked, the rear end to see if you either need to fill or change the gear oil in the rear end of your truck, it needs to bee checked every six months.

Sep 12, 2009 | 1991 Toyota Pickup

1 Answer

No spark inline six turns over strong, has fuel,


take the cap off of the distributer grab the rotor and make sure it does not spin freely if it dooes the pin had sheared off the gear if not replace the ignition module on the distributer if if there you should see it if not it will be on drivers fender

Aug 09, 2009 | 1988 Ford F 150

2 Answers

1998 ford motor swap 8cyl to a six inline


Unfortunately, You will need to Change it all. None of the V8 Components will Transfer to the Inline 6. Please Rate My Response! Thanks!

Feb 02, 2009 | 1998 Ford F150 Regular Cab

1 Answer

4.0ltr powertech inline six


It shouldn't be a problem, just clearance issues might be a problem in turns making it a pain to park

Nov 20, 2008 | 2000 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

71231 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7001 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...