Question about 1995 Pontiac Grand Am

3 Answers

Turn signals I just bought a 1995 grand am gt and the turn signals wont work at all..I had the fuse looked at and its good that was it...but I was curious due to the fact that they dont work at all not even light up it's like they are totally dead...what could be the problem? everything else as far as lights work fine...

Posted by on

  • 1 more comment 
  • scdjcd Dec 13, 2008

    Also have a 95 Pontiac. Right signal works fine, left signal - one bulb in back and one small white bulb in front will go on when the turn level is pulled down so I can (kind of) manually work a left turn signal. Emergency flashers don't work at all. Very seldom, all lights will go out until the lever is frantically jiggled.

  • Anonymous Dec 27, 2008

    mis luses lateral no funcionan que puedo hacer

  • Anonymous Mar 06, 2009

    Turn signals will not work. Fuse is good. Bulbs are good. Turn signal lever seems to be working properly, its not loose.

×

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Pontiac Master
  • 1,779 Answers

Replace the turn signal flasher. Located left side of steering column bracket, behind instrument panel. Pull out to remove, push in to install. Let me know if u need more help w/ it.

Posted on Nov 20, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 68 Answers

Well u could have a cut wire somewhere if the fuzes where good or ur light bulbs for the signals could be blown or the fuze is to big for them and it over loades them and blows them,. i hope that helps

Posted on Nov 20, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Replace the turn sidnal switch on the steering colum

Posted on Nov 20, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jeep 2007 no turnsignals work but fashers work


turns dead on 4 corners???????????????
HAZ flasher, works.
check fuses first. many cars run 2 fuse here, 1 for each.
also alldata.com has the schematic , look there if fuse is good.
there are 2 fuse boxes, look in both,(allcars) look both.
on about 1996, all cars, then started to move fuse forward due
to insane increases of in car electrics. (space limits)

Jan 16, 2014 | 1997 Jeep Grand Cherokee

1 Answer

Turn signals wont work bulbs ok dont have a manual to the car dont know wich fuse goes to the turn signals


pickup a test light and check all the fuse if the fuses are good then you probably have a bad signal flasher.make sure you change the signal flasher and not the emergency flasher as they look the same.

Jul 30, 2011 | 1995 Ford Mustang

2 Answers

I have a 1995 grand prix Blinkers dont work but, other lights do.


First check turn signal fuse and relay if, they are good then try pressing on and off the hazard switch while turning the signal switch on.If signals start to work replace hazard switch.If hazard switch is good then replace turn signal switch.

May 02, 2011 | 1995 Pontiac Grand Prix

1 Answer

No turn signals or hazards???


Check the FLASHER unit; the turn signal flasher is mounted in a clip on the right side of the steering column support bracket. The hazard flasher is located in the component center, under the instrument panel, on the right side. Replace the flasher by unplugging the old one and plugging in the new one.

Hazard flasher -->> The Flasher is located: Front seating area, passenger side, under dash, below glove compartment, mounted in fuse panel

Turn signal -->> The Flasher is located: Front seating area, driver side, under dash, mounted on passenger side of steering column

Good luck (remember comment and rated this).

Apr 23, 2010 | 1995 Chevrolet Monte Carlo

3 Answers

Turn signals wont work fuses are good?


the hazard switch above the radio is your problem. if you put on your signals and they don't flash turn hazards on then off and they will flash. (changing this *** will fix your problem

Aug 30, 2009 | 1999 Pontiac Grand Am GT

1 Answer

Need turn signals to work


could be a fuse, if the fuse is good find out where the flasher relay is located and check to see if there is power there when the indicators are operated. hope this helps.

Apr 23, 2009 | 2000 Pontiac Grand Am GT

1 Answer

Turn singals & blower motor stop working at same time


look in your high current fuse box (distribution box) under the hood, inside the box are 4 relays and two rows of fuses, the center row of fuses the second fuse (next to starter/alt fuse if marked) is a 50 amp fuse for turn signals and blower motor, see if it is good, let me know what you find

Apr 13, 2009 | 1995 Mercury Grand Marquis

1 Answer

1995 Pontiac Grand Am - fuses


check fuse in your fuse box if all the fuse are good you may have different problem
1- loose fuse
2- loose wire
3-electrical switch panel light is bad

Apr 07, 2009 | 1995 Pontiac Grand Am

1 Answer

Turn signals wont work


First check the bulbs,fuse and the relay if they are fine then its the problem with turn switch......


Good luck....

Nov 20, 2008 | 1995 Pontiac Grand Am

Not finding what you are looking for?
1995 Pontiac Grand Am Logo

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...